DBUB-P2 Bluetooth Adapter User’s Manual This document provides safety instructions and describes the specifications. Read this document carefully before installing to ensure your safety and product performance.
Federal Communication Commission (FCC) Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Country Code selection feature to be disabled for products marketed to the US/CANADA. Operation of this device is restricted to indoor use only This device is intended only for OEM integrators under the following conditions: 1. The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2.
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Antenna information Type Connector Peak Gain(dBi) PIFA NO 2.
Industry Canada statement: This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
1) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne. Tant que les 1 condition ci-dessus sont remplies, des essais supplémentaires sur l'émetteur ne seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformité supplémentaires requis pour ce module installé.
show in this manual. Manuel d'information à l'utilisateur final L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à la façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intègre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et avertissements comme indiqué dans ce manuel. Antenna information Type Connector Peak Gain(dBi) PIFA NO 2.
Caution: Be aware of the following limits before using the Bluetooth Adaptor. Do not subject the Bluetooth Adaptor to high temperatures, direct sunlight or moisture. Do not bend, or subject the Bluetooth Adaptor to strong impacts. Do not disassemble or alter the Bluetooth Adaptor in any way. Do not attempt to install the Bluetooth Adaptor in any incompatible device. Do not remove the Bluetooth Adaptor from the TV’s during operations.
Setup the Bluetooth connection The Bluetooth adapter is pre-installed in the TV set. No extra installation steps are required for users. Follow the steps below to start using the feature of this adapter: 1. Turn on your TV. 2. Switch to the channel that delivers 3D contents. If you are watching a disc with 3D contents, you will also need to activate your player for playing the disc. 3. Turn on your 3D glasses. 4. The 3D glasses will pair with this Bluetooth adapter automatically and are now ready for use.
Specification Item Contents Frequency range: 2402-2480MHz Channel spacing: 1MHz Channel List: 79 channels Modulation type: GFSK, π/4 – DQPSK, 8DPSK Modulation technology: GFSK Conducted output power: 10dBm Antenna type: PIFA antenna Antenna gain(dBi): 2.68 Antenna connector: NA Operating temperature: 0~60℃ Power supply 3.3Vdc from host * Transfer rate are theoretical values; however, actual communication rate will vary according to communication environment or connected equipment.
