WLAN b+g mini-PCI Module RM1 OEM Installation Manual (The module is sold only to the OEM integrators & the manual is valid only for the OEM manufactures) Version: 1.
Copyright Statement No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, whether electronic, mechanical, photocopying, recording or otherwise without the prior writing of the publisher. Windows™ 98SE/2000/ME/XP are trademarks of Microsoft ® Corp. Pentium is trademark of Intel. All copyright reserved.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents Table of Contents ................................. 3 1. Introduction ..................................... 4 1.1 The WLAN 802.11b+g mini-PCI Module 4 1.2 Hardware Installation & Antenna Information 4 *Caution !! ........................................... 6 (1). This module cannot be bound in a tablet computer for RF exposure issues. (See label 1)6 (3). This module must be labeled with FCC ID. (See label 2) 6 (4).
1. Introduction 1.1 The WLAN 802.11b+g mini-PCI Module Thank you for purchasing the WLAN b+g mini-PCI Module that provides the easiest way to wireless networking. This User Manual contains detailed instructions in the operation of this product. Please keep this manual for future reference. SYSTEM REQUIREMENTS l Microsoft® Win™ 2000/ME/98 Second Edition/XP 1.2 Hardware Installation & Antenna Information l MODULE IS INSTALLED IN THE ROUTER. (SEE THE FOLLOWING DIAGRAMS).
l Antennas are embedded in the two sides (see the two antennas shown below) Aux Main Only the antenna type listed below can be used: (1) Vendor WanShih Electronic CO. Model: Wss002 Important Note: This module is restricted to mobile configuration. The antennas of module should be installed and operated with minimum distance 20cm between the radiator and all persons. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
*Caution !! (1). This module cannot be bound in a tablet computer for RF exposure issues. (See label 1) Label 1 (3). This module must be labeled with FCC ID.
(4). If the FCC ID is not visible when the module is installed inside another device, then the outside of device must also display a label referring to the enclosed module. The exterior label can be “ Contains Transmitter Module FCC ID:NKRRM1 ” or similar wording. (See label 3) Label 3 Please put Label 3 to the enclosure of end product to note the end user.
2.
3. Hardware Connections 1. Have your Access Point Prototyping Board ready. 2. Find the mini-PCI slot on the Prototyping Board.
3. Insert the WLAN 802.11g mini-PCI Module into the mini-PCI slot on the Prototyping Board. 4. Press down the Module until it is secured with the two latches on the Board. 5. Hardware Installation is completed.
4. Remove the Module 1. Release the two latches by gently remove them aside. 2. The module pops up. Remove the Module.
5. Basic Configuration of your Access Point This section gives you an example of the general basic configuration procedure for your Access Point. It describes how to set up the Access Point for Infrastructure BSS operation, and the configuration of the local LAN environment. Although the Command Line Interface (CLI) may also be used to configure the Access Point, the example we are using here is the browser-based configuration mechanism.
5.1 Logging On If you attempt to access a configuration item from the browser menu, an administrator login screen will appear, prompting you to enter the password in order to log on. If you are logging on for the first time, you should use the factory default setting “password”. The password is always displayed as a string of asterisks (“*”). Clicking the LOG ON button will begin the configuration session. 5.
5 . 2 . 2 D E V I C E I P S E T T I NGS The Device IP setting screen allows you to configure the IP address and subnet of the AP on the LAN. Although you can rely on a DHCP server to assign an IP address to the Access Point automatically, it is recommended that you configure a static IP address manually in most applications.
this device”, and then press Next to the next screen. Again, as a reminder, it is recommended that your Access Point should be assigned a static IP address in order for you to be able to manage it later on. 5.2.3 CONFIGURE YOUR WIRELESS LAN CONNECTION Network Name (SSID): The SSID is the network name used to identify a wireless network. The SSID must be the same for all devices in the wireless network. Several Access Points on a network can have the same SSID. The SSID can be up to 30 characters long.
searching for Access Points in the wireless network. Select Disable if you do not want the device to broadcast the SSID. Channel: Select the channel from the available list to match your network settings. All devices in the wireless network must use the same channel. Note: The available channel numbers are different from country to country. USA and Canada: CH01~11, Europe: CH01~CH13, Japan: CH01~CH14, France: CH10~CH13, Spain: CH01~CH13.
Note: If you change the AP’s IP address, as soon as you click on FINISH you will no longer be able to communicate with your Access Point. You need to change your IP address and then re -boot your computer in order to resume the communication.
