INSTALLATION & OPERATION MANUAL HMD SERIES HumidiHeat™ HOLDING & TRANSPORT CABINETS MODELS: 1826-5-HMD 1826-13-HMD 1826-15-HMD For additional information on Wittco or to locate an authorized parts and service provider in your area, visit our website at www.wittco.com WITTCO FOODSERVICE EQUIPMENT DIVISION OF ITW FOOD EQUIPMENT GROUP, LLC. www.wittco.
HMD SERIES F-41142 (10-09) IMPORTANT FOR YOUR SAFETY THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL ELECTRICAL EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD STARTUP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL. FOR YOUR SAFETY DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS OR LIQUIDS IN THE VICINITYOF THIS OR ANY OTHER APPLIANCE. WARNING IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE, OR MAINTENANCE CAN CAUSE PROPERTY DAMAGE, INJURY, OR DEATH.
HMD SERIES F-41142 (10-09) TABLE OF CONTENTS IMPORTANT FOR YOUR SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HMD SERIES F-41142 (10-09) GENERAL UNPACKING: The Cabinet was inspected before leaving the factory. The transportation company assumes full responsibility for safe delivery upon acceptance of the shipment. Immediately after unpacking, check for possible shipping damage to the cabinet. INTRODUCTION Wittco HumidiHeat™ Holding & Transport Cabinets are produced with quality workmanship and material.
HMD SERIES F-41142 (10-09) 8. Install tray slides in the cabinet. 9. Ensure that the hook on the end of the tray slide is up. ELECTRICAL REQUIREMENTS ELECTRICAL CODES & STANDARDS: The cabinet must accordance with: CLEANING: The cabinet should be thoroughly cleaned prior to putting into service. be installed in In the United States of America: 1. State and Local Codes. 2. National Electrical Code, ANSI/ NFPA-70 (latest edition.
HMD SERIES F-41142 (10-09) receptacle is not the proper grounding type, contact an electrician. DO NOT REMOVE THE GROUNDING PRONG FROM THIS PLUG. Verify that the power source matches the Serial Data Plate located on the lower back corner of the cabinet and the plug configuration before the connection is made. (Fig.1) Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance. (Fig.3) (Fig.
HMD SERIES F-41142 (10-09) OPERATION the temperature. Holding temperature range is from 80⁰F. to 200⁰F. CONTROLS OPERATING INSTRUCTIONS 1. Connect to proper electrical supply as indicated on data plate. 2. Fill water into Water Reservoir. (Reservoir holds approx. 1 gallon or 3.78 liters of water.) The water level can be observed through the sight glass. (Fig. 4) To avoid lime build-up, it is recommended that you use only distilled or softened water. WATER RESERVOIR Located on top of cabinet.
HMD SERIES F-41142 (10-09) As humidity is increasing to the desired setting, the Humidity Control Sensor Light will be lit RED. When the desired humidity has been reached, the light will change to GREEN. CLEANING Always ELECTRICAL POWER before cleaning. UNPLUG SUPPLY DAILY: NOTE: The temperature in any heated cabinet will fluctuate as the heating element(s) cycles on and off. The thermostat setting will provide an average temperature in the cabinet.
HMD SERIES F-41142 (10-09) HEAVY-DUTY CLEANING: For heavy-duty cleaning, use warm water, a degreaser, and a plastic, stainless steel, or Scotch-Brite pad. Never rub in a circular motion -- rub gently in the direction of the steel grain. Always rinse thoroughly. STAINLESS STEEL CARE 4. Never rub in a circular motion. Always rub gently in the direction of the steel grain. 5. Never leave any food products or salt on the surface. Many foods are acidic. Salt contains chloride.
HMD SERIES F-41142 (10-09) TROUBLESHOOTING SYMPTOMS Cabinet not operating POSSIBLE CAUSES Cabinet not connected to power source. REMEDY Connect Cabinet to power source. Check circuit breaker Check GFCI No power. GFCI or Ground Fault Damaged element, wire, Circuit Indicator power cord, etc. tripped. Contact Authorized Service Provider. Cabinet is connected to power source, Damaged element, wire, circuit breaker is ON, power cord, etc. GFCI is ON, but cabinet is not heating.
HMD SERIES F-41142 (10-09) SPECIFICATIONS HEIGHT MODEL No. IN (mm) DEPTH IN (mm) WIDTH IN (mm) 1826-5-HMD 32.375" 34.25" 25.125 1826-13-HMD 59.375" 34.25" 25.125" (1700mm) (857mm) (724mm) 34.25" 25" 1826-15-HMD 65" (1702 mm) (857mm) (724mm) SHIPPING WT. Lb.
HMD SERIES F-41142 (10-09) WIRING DIAGRAM 11