INSTALLATION & OPERATION MANUAL DRAWER WARMERS CHIP WARMERS MODELS: CHIP WARMERS: 200-1-CW 200-2-CW DRAWER WARMERS: CAFÉ: 200-1R-C 200-2R-C 200-3R-C 200-4R-C CAFÉ; BUILT-IN: 200-1R-BI-C 200-2R-BI-C 200-3R-BI-C 200-4R-BI-C SLIMLINE LOW PROFILE : SLIMLINE BUILT-IN : 200-1-SL-LP 200-2-SL-LP 200-1-SL-BI 200-2-SL-BI R-SERIES : R-SERIES BUILT-IN : 200-1R 200-2R 200-3R 200-4R 200-1R-BI 200-2R-BI 200-3R-BI 200-4R-BI WITTCO FOOD SERVICE EQUIPMENT DIVISION OF ITW FOOD EQUIPMENT GROUP, LLC www.wittco.
DRAWER & CHIP WARMERS F-41015 (03-14) IMPORTANT FOR YOUR SAFETY THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL ELECTRICAL EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD STARTUP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL. FOR YOUR SAFETY DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS OR LIQUIDS IN THE VICINITYOF THIS OR ANY OTHER APPLIANCE. Improper installation, adjustment, alteration, service, or maintenance can cause property damage, injury, or death.
DRAWER & CHIP WARMERS F-41015 (03-14) TABLE OF CONTENTS IMPORTANT FOR YOUR SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DRAWER & CHIP WARMERS F-41015 (03-14) GENERAL If the warmer is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery. INTRODUCTION WITTCO Drawer Warmers and Chip Warmers are produced with quality workmanship and material. Proper installation, usage, and maintenance of your warmer will result in many years of satisfactory performance. Carefully unpack warmer and place in a work accessible area. 1. Remove banding holding the carton to the pallet. 2.
DRAWER & CHIP WARMERS F-41015 (03-14) TRIM KIT INSTALLATION 2. Place Trim Kit flush with the front of the Drawer Warmer. 3. Trim Kit has 4 mounting holes. There are two holes on the bottom and two holes on the top. Models: 200-1R-BI-C, 200-2R-BI-C, 200-3R-BI-C, 200-4R-BI-C, 200-1R-BI, 200-2R-BI, 200-3R-BI, 200-4R-BI. Built-in Drawer Warmers come with a “trim kit.
DRAWER & CHIP WARMERS F-41015 (03-14) Please refer to the Electrical Requirements in the Installation & Operation Manual.” 6. Slide/install Warmer wall/cabinet opening. into 7. Reinstall drawer assemblies into warmer – Top to Bottom ELECTRICAL REQUIREMENTS ELECTRICAL CODES & STANDARDS: The warmer must accordance with: be installed All warmers are equipped with a three-prong plug. It is imperative that this plug must be connected into a properly grounded three-prong receptacle.
DRAWER & CHIP WARMERS F-41015 (03-14) OPERATION POWER LIGHT CONTROLS The Warmer and its parts are hot. Be very careful when operating, cleaning, or servicing the warmer. The warmer Control Panel contains an operating indicator light and a full range thermostat. (Fig.2) THERMOSTAT DIAL: The thermostat also acts as the On/Off switch to the warmer system. Turning the thermostat counter clock-wise until it stops will turn the warmer off.
DRAWER & CHIP WARMERS F-41015 (03-14) approximate temperatures is below. (Fig. 4) Thermostat Setting 1 2 3 4 5 6 7 8 9 10 (Fig. 3) THERMOMETER Approximate Temperature 100⁰F (37⁰C) 110⁰F (43⁰C) 120⁰F (49⁰C) 130⁰F (54⁰C) 140⁰F (60⁰C) 150⁰F (66⁰C) 160⁰F (71⁰C) 170⁰F (77⁰C) 180⁰F (82⁰C) 190⁰F (88⁰C) (Fig. 4) The greater the thermostat number setting, the higher the temperature. The lower the thermostat number setting, the lower the temperature.
DRAWER & CHIP WARMERS F-41015 (03-14) CLEANING STAINLESS STEEL CARE The Warmer and its parts are hot. Be very careful when operating, cleaning, or servicing the warmer. CLEANING: Stainless Steel contains 70 – 80% iron, which will rust if not properly maintained. Stainless Steel also contains 12 – 30% chromium, which forms an invisible passive, protective film that shields against corrosion. Unplug electrical power supply before cleaning. DAILY: 1. Unplug electrical power supply. 2.
DRAWER & CHIP WARMERS F-41015 (03-14) HEAT TINT: Darkened areas, called “heat tint,” may appear on stainless steel exposed to excessive heat. Excessive heat causes the protective film to thicken. This is unsightly, but is not a sign of permanent damage. PRESERVING & RESTORING: Special stainless steel polishing cleaners can preserve and restore the protective film.
DRAWER & CHIP WARMERS F-41015 (03-14) TROUBLESHOOTING SYMPTOMS POSSIBLE CAUSES Warmer not operating REMEDY Warmer not connected to power source. Connect cabinet to power source. No power Check Circuit Breaker and/or check GFCI switch on outlet. GFCI or Ground Fault Circuit Indicator tripped Moisture problem. Shorted element Pinched/damaged wire. Damaged power cord. Dry moisture problem. Contact Authorized Service Provider. Contact Authorized Service Provider. Contact Authorized Service Provider.
DRAWER & CHIP WARMERS F-41015 (03-14) 11
DRAWER & CHIP WARMERS F-41015 (03-14) 12
