WT-1010SA S ST TA AN ND D--A ALLO ON NE EG GS SM MA ALLA AR RM MS SY YS ST TE EM M User Manual W R R R W T U A C O P O A T O N S D N B H D WIIIT TU UR RA AC CO OR RP PO OR RA AT TIIIO ON NS SD DN NB BH HD D
WT-1010SA USER MANUAL Sketch of the WT-1010SA LCD Display Display Signal Strength, Programming Status and etc. SIM Card Holder Insert SIM here GSM Module GSM Transmission Lithium-Ion Battery Back-up when Power Failure Connector Block All wiring must be connected here Antenna The antenna must be well connected before turn on the terminal Connection Diagram WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.
WT-1010SA USER MANUAL Please check the following packing list: Name WT-1010SA Main Unit Telephone line Power adapter Lithium-Ion Back-up Battery 5m GSM terminal antenna User’s Manual Quantity 1 1 1 1 1 1 Unit set set set set set set Contents 1. Introduction to WT-1010SA GSM Alarm System………………………………………………………………………5 2. Main Features of the WT-1010SA……………………………………………………………………………………………………5 3. Installation Instruction……………………………………………………………………………………………………………………6 3.
WT-1010SA USER MANUAL 6. Miscellaneous Settings……………………………………………………………………………………………………………………32 7. Technical Specifications………………………………………………………………………………………………………………………………41 WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.
WT-1010SA USER MANUAL 1. Introduction to the WT-1010SA GSM Alarm System The WT-1010SA GSM Alarm System provides the ideal solution for residential, commercial applications, rural and farm security where traditional telephone lines are not available for security system communications. When no telephone service is available from your home, it ensures that critical alarm information reaches the central station.
WT-1010SA USER MANUAL 8. Most of the countries, GSM Mobile operator offer cheaper call plan compared to telecom landline. It can connect to the basic telephone to make call and if any intruder, the WT-1010SA will cut the telephone call and send the alarm messages first. 9. In order to prevent professional thief to disconnect GSM by using “GSM Jammer”, the WT-1010SA will transmit the alarm if signal drop immediately and trigger the siren 10.
WT-1010SA USER MANUAL 3.2) WT-1010SA Inputs and Outputs Wiring Instructions RLY1 (OUT1), RLY2 (OUT2), RLY3 (OUT3) Remote Controlling Outputs These open collector outputs can be turned on and off remotely through a SMS. Remote control will be reachable by sending a SMS with a certain command. Note: When sending normal SMS with command below, the WT-1010SA will turn On / Off the output relay and reply a message of output has turned On / Off to a programmable phone numbers.
WT-1010SA USER MANUAL 3.3) Installing the SIM Card Note: Installing the SIM Card. Please be sure the initial 4 digit PIN code of SIM card is disabled. This can be done by placing it in an unlocked Mobile phone and first checking if the SIM requested any PIN code. If this is the case the PIN code can be disabled using the security settings on the phone. Warning! The WT-1010SA identifies only 3V SIM Card. Proceed as follows: 1. 2. 3. 4.
WT-1010SA USER MANUAL 3.5) Dialing a number from the attached telephone set After the GSM module is connected to the GSM network, an attached fixed line phone can be used to make calls. If you pick up the phone, you will hear a dial tone. Simply dial the number you want to call (as if you are dialing from a normal fixed line phone). You can also dial the WT-1010SA unit’s phone number from another phone, and its attached phone will ring as a normal landline phone would.
WT-1010SA USER MANUAL 4. WT-1010SA Programming Instructions (Via Fixed Line Phone) 4.1 Introduction The WT-1010SA can be programmed manually by a connected normal telephone. Note: Before commencing programming it is advisable to read the below programming setting instructions thoroughly. To start with programming, user must plug-in a normal single line phone to TEL1 (Port 1) Step 1. Enter Programming Mode Pick up the handset or press hands free, press **123456# to enter programming mode.
WT-1010SA USER MANUAL HAND FREE… Programming Mode Step 2. Reset the WT-1010SA Unit To reset the unit, you can press *15* to proceed. REST ON&OFF: REST ON&OFF: 1 Then press 1# to reset REST ON&OFF: 1 OK Note: It is advised that you should reset the WT-1010SA unit before proceeding to the below programming section Step 3.
WT-1010SA USER MANUAL TEL: OK Number has programmed successfully You may continue to program administrator number 2, 3, 4, 5, 6, 7 and 8 by pressing *2* , *3* , *4* , *5* , *6* , *7* , *8* Step 4. Setting the Recipient that will receive Alert Messages The unit can send text alerts to 1 or all 8 of the programmed administrator’s numbers. To do this setting, you can press *18* to proceed.
WT-1010SA USER MANUAL NEW AREA: 03 Enter area code 03 for example and ended with # NEW AREA: 03 OK Area code has programmed successfully Step 6. Setting the Function of Adding Area Code when Transmitting an Alarm To turn on/off this function, you can press *14* to proceed. AREA ON&&OFF: AREA ON&&OFF: 1 To turn on this function simply press 1# To turn off this function simply press 0# AREA ON&&OFF: 1 OK Default Value: 0 Step 7.
WT-1010SA USER MANUAL DTTRANSMIT: 07 Example: To set the required delay time at 7 seconds Simply press 07# DTTRANSMIT: 07 OK Note: The Delay Time is a 2 digits value range from 00 – 59 seconds (Default: 00 seconds) Step 8. Setting for calling a group of Administrator numbers To program the unit to dial a certain group of numbers for PSTN/AC failure or Auto Test, you can press *29* to proceed.
WT-1010SA USER MANUAL TIME: 08 : 30 : 00 Example: To set the time at 8.30am Simply input digits and ended with # TIME: 08 : 30 : 00 9.2) OK Setting the Auto Test Report Time Section 1 The system has the function of sending the test report to the administrators at the programmable time section. The time is entered in 24 Hour format. To program the auto test report time section 1, you can press *17* to proceed. DSTM1: : : DSTM1: 12 : 00 : 00 Example: To set the auto test report time at 12.
WT-1010SA USER MANUAL DSTM2: : : DSTM2: 18 : 00 : 00 Example: To set the auto test report time at 18.00pm Simply input digits and ended with # DSTM2: 18 : 00 : 00 OK Note: Skip this setting if only 1 time section is needed. 9.4) Setting the Auto Test Report Time Section 3 The system has the function of sending the test report to the administrators at the programmable time section. The time is entered in 24 Hour format. To program the auto test report time section 3, you can press *43* to proceed.
WT-1010SA USER MANUAL 9.5) Enable/Disable the function of dialing the programmed Administrator number for Auto Test To turn on this function, you can press *27* to proceed. DTIMEC ON&&OFF: DTIMEC ON&&OFF: 1 To turn on this function simply press 1# To turn off this function simply press 0# DTIMEC ON&&OFF: 1 OK Default Value: 0 9.6) Enable/Disable the generation of SMS Report for Auto Test To turn on this function, you can press *28* to proceed.
WT-1010SA USER MANUAL Step 10. Setting for PSTN Failure To turn on this function, you can press *30* to proceed. PST: ME: CA1: OU: CA2: PST: ME: 1 OU: 1 CA: 1 AL: AL: 1 CA2: 1 Example: Setting the unit to generate an Alert Message, call the administrators, generate a pulse (+V) and sound the audible alarm when PSTN failed. Simply input 11111# PST: ME: 1 OU: 1 CA: 1 CA2: 1 AL: 1 OK Description: “ME” stands for generation of SMS when PSTN failed.
WT-1010SA USER MANUAL Step 11. Setting for AC Failure To turn on this function, you can press *31* to proceed. ADC: ME: AL: CA1: CA2: ADC: ME: 1 AL: 1 CA1: 1 CA2: 1 Example: Setting the unit to generate an Alert Message, call the administrators, generate a pulse (+5V) and sound the audible alarm when AC failed. Simply input 1111# ADC: ME: 1 AL: 1 CA1: 1 CA2: 1 OK Description: “ME” stands for generation of SMS when AC failed. Default: 0 “AL” stands for sounding the audible alarm when AC failed.
WT-1010SA USER MANUAL Step 12. Setting for Overcoming GSM Jammers & GSM Tower Failure 12.1) Enable/Disable the function of Activate Output Relay 1 when GSM Jammer is detected To turn on this function, you can press *38* to proceed. NETWORK ON&&OFF: NETWORK ON&&OFF: 1 To turn on this function simply press 1# To turn off this function simply press 0# NETWORK ON&&OFF: 1 OK Note: Alarm siren connected to PIN6 & PIN7 will sound when jammer is detected 12.
WT-1010SA USER MANUAL Description: “NETDT1” stands for network failure time range from 00 – 59 seconds. Default: 6 seconds. “RLY1” stands for turn on time of Relay 1 when network fails (00 – 59 seconds), 00 means RLY1 will stay ON permanently. 12.3) Enable/Disable the function of Activate Output Relay 2 when GSM Tower Failure To turn on this function, you can press *40* to proceed.
WT-1010SA USER MANUAL NETDT2: 06 RLY2: 10 OK Description: “NETDT2” stands for network failure time range from 00 – 59 seconds. Default: 6 seconds. “RLY2” stands for turn on time of Relay 2 when network fails (00 – 59 seconds), 00 means RLY2 will stay ON permanently. Step 13. Input Settings 13.1) Turn on the function of Inputs To turn on the function of input number 1, you can press *24* to proceed.
WT-1010SA USER MANUAL You may continue to activate Input 2, Input 3 and Input 4 functions by pressing *25*, *26* or *46* Note: Please refer to programming instructions via SMS for editing the Input Alert messages on page 27 Step 14. Arm and Disarm the System (Via Fixed Line Phone) To arm the system, you can press *10* to proceed.
WT-1010SA USER MANUAL Step 15. Enable the Remote Control The WT-1010SA also comes with a RF remote control. It allows you to arm or disarm the system easily from a close distance. To enable the remote control, you can press *45* to proceed.
WT-1010SA USER MANUAL Step 16. Setting the Automatic Call Answering Feature The WT-1010SA can be programmed to answer all incoming calls automatically even there is no fixed line phone attached to it. When the call is answered, it allows the owner to arm or disarm the system by entering a command from their phone’s keypad. To turn on this function, you can press *35* to proceed.
WT-1010SA USER MANUAL 5. WT-1010SA Programming Instructions (Via SMS) Programming the WT-1010SA can also be done via SMS commands using your phone. Any programming command sent by SMS must be in CAPITAL letters. The fields between square brackets are parameters; do NOT enter the square brackets. When you send a command, you will receive the answer for the first time even if your GSM number is not in the administrator list.
WT-1010SA USER MANUAL XXXXXX… stands for message contents Example: If you want the SMS Report to display “Status:Online”, you would send the following SMS message to the unit. *TSMS#Status:Online Return Message TSMS=Status:Online 5.3 Editing the Inputs Alert Messages (When High Pulse) The Input Alert Message can be edited and programmed up to 50 characters. You can change the displayed text by sending the following commands by SMS message to the unit.
WT-1010SA USER MANUAL XXXXXX… stands for alert message content Example: If you want the alert message to display “Garage Closed!” when input 1 triggered; you would send the following SMS message to the unit. *USC1#Garage Closed! Return Message USC1=Garage Closed! 5.5 Output Settings 5.5.1 Activate Output Relay to Stay On for a Specific Time To activate the output relay, you can send a text command via SMS specifying the number of seconds the output should stay on to the unit.
WT-1010SA USER MANUAL 5.6 Arm and Disarm the System (Via SMS) It is possible to arm and disarm the system by SMS. You can send the following text command to unit. Text Command: *DARM#X X stands for ON (1) or OFF (0) value Example: To arm the system, you can send the following text message to the unit. *DARM#1 Return Message ARM To disarm the system, you can send the following text message to the unit. *DARM#0 Return Message DISARM WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.
WT-1010SA USER MANUAL 6. Miscellaneous Settings Inquire All Programmed Administrator Number via Voice To inquire all administrator numbers, you can press *32* to proceed. ADMIN: 1: 1234567890 All the administrator numbers will be displayed in sequence Deleting the Administrator Number via Voice Example: To delete the programmed administrator number 1, you can press *1* to proceed. TEL: 1# TEL: 1# Simply press # to delete DEL1: OK WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.
WT-1010SA USER MANUAL Changing the Programming Mode Password via Voice To change the 6 digits programming mode password, you can press *0* to proceed. NEW PASSWORD: NEW PASSWORD: 654321 Input new password and ended with # NEW PASSWORD: 654321 OK Inquire the status of the Recipients that will receive Alert Messages via Voice To inquire the status of the recipients, you can press *19* to proceed.
WT-1010SA USER MANUAL Setting the Waiting Time for Engaged Call via Voice In the event the administrator has not answered the call or engaged, it could take a while for the WT-1010SA to call the next number. You can shorten the time for every call by programming the waiting time. Press *12* to proceed.
WT-1010SA USER MANUAL OK Note: The Arm Time is a 2 digits value range from 00 – 59 seconds (Default: 00 seconds) Enable/Disable System Power Up SMS Notification The system is able to generate SMS notification whenever the WT-1010SA is turned on. To enable this function, you can press *48* to proceed.
WT-1010SA USER MANUAL To enable this function simply press 1# To disable this function simply press 0# ARM MESSAGE ON&&OFF: 1 OK Default Value: 0 Disable the Remote Control To disable the remote control, you can press *50* to proceed.
WT-1010SA USER MANUAL IN2D TIME: 60 Example: To set the alarm delay time for 60ms Simply input 60 and ended with # OK Note: The Alarm Delay Time is a 2 digits value range from 00 – 99ms (Default: 00ms) You may continue programming Input 3 and Input 4 Alarm Delay Time by pressing *52* or *53* Activate Output Relay to stay on for a specific time via Voice To activate output relay 1 to stay on for a specific time, you can press *21* to proceed.
WT-1010SA USER MANUAL Setting the Alarm Time for Audible Alarm via Voice To set the alarm time for audible alarm, you can press *33* to proceed.
WT-1010SA USER MANUAL DEL-NUM: 2 OK Note: The value is 0 – 4 (Default: 0) Adjusting the Speaker and Microphone Volume level via Voice To adjust the speaker and microphone volume level, you can press *11* to proceed. SPK: MIC: SPK: 3 MIC: 3 Example: To adjust the speaker volume to 3 and microphone volume to 3 Simply press 33# SPK: 3 MIC: 3 OK Note: Both SPK and MIC volume level range from 1 – 4 (Default: 1).
WT-1010SA USER MANUAL Inquire All Programmed Administrator Number via SMS To inquire all the programmed administrator number, you can send the following SMS command to the unit. Text Command: *ADM?# Example of Return Message 1: 13256997049 2: 15915325252 3: 13456679988 4: 5: 6: 7: 8: Checking the Signal Strength via SMS To check the signal strength of the unit, you can send the following SMS command to the unit.
WT-1010SA USER MANUAL Changing the Programming Mode Password via SMS It is possible to change the login password by sending the following SMS command. Text Command: *PAWO#XXXXXX XXXXXX stands for 6 digits New Password Example: To change the password to 654321, you would send the following SMS command to the unit. *PAWO#654321 Return Message: PAWO-OK Inquire the Status of Inputs, PSTN and AC To inquire the status of inputs, PSTN and AC, you can send the following SMS command to the unit.
WT-1010SA USER MANUAL *ALNF#X X stands for ON (1) or OFF (0) value When *ALNF#1 is applied, means audible alarm will sound. When *ALNF#0 (Default) is applied, means audible alarm will turn off. Reset the WT-1010SA unit via SMS To reset the unit, you can send the following command by SMS to the unit. Text Command: *REST#XXXXXX XXXXXX stands for 6 digits password based on *PAWO# (Default: 123456) and it can be changed anytime. Return Message REST-OK 7. Technical Specifications 1.
WT-1010SA USER MANUAL Warranty Witura Corporation Sdn Bhd guarantees all WT-1010SA GSM Fixed Wireless Terminal against defective parts and workmanship. Witura Corporation Sdn Bhd shall, at its option, repair or replace the defective equipment upon the return of such equipment to any Witura branch.