WT-1041 3 3G GC Ca am me erra a User Manual W R C O R O R O N S D N W T U A P A T B H D OR NS DN NB WIIIT TU UR RA AC CO RP PO OR RA AT TIIIO ON SD BH HD D
WT-1041 3G Camera INTRODUCTION Your WT-1041 3G Camera is a smart monitor device, which is used in 3G network. You can conveniently monitor your home or any place via a simple SMS command. With the built in 1.3 million pixels camera, you can catch every wonderful time in your life. FEATURES Multi share numbers setting (50 at most) Password setting Real-time monitor Video recording Photo taking (1.
WT-1041 3G Camera TABLE OF CONTENTS 1. Important Precaution…………………………………………………………………………………………………5 Precaution………………………………………………………………………………………………………………5 Battery and power transformer……………………………………………………………………………6 Use precaution………………………………………………………………………………………………………7 2. WT-1041 3G Camera…………………………………………………………………………………………………8 Front view………………………………………………………………………………………………………………8 Rear view………………………………………………………………………………………………………………9 Bottom view……………………………………………………………………………………………………………9 3.
WT-1041 3G Camera 1. IMPORTANT PRECAUTION Before using WT-1041 3G Camera, please read the following precaution first to avoid shock, fire and device damage. Precaution Do not use the product in damp place. This device is a wireless communication application, pay attention to the place where you use, don’t use when prohibited. Follow the entire safety usage guide applied on wireless communication device; breaking the rules may be dangerous or illegal.
WT-1041 3G Camera Battery And Power Transformer WT-1041 3G Camera use the rechargeable battery. Every changing take about 22.5 hour. When the operating time is noticeably shorter than normal, don’t attempt to replace the battery, contact after sales service center for replacement. About battery maintenance, Please refer to page 5 Maintenance Precaution and the State in the last page. Do not connect or disconnect AC power transformer with wet hands, or it will cause shock.
WT-1041 3G Camera Use Precaution Do not place the product before the light source to avoid over light-exposing. Do not place any things within 1 meter before the product. (The shot video may be unclear.) Do not place the device in the area with poor signal. Do not cover the device with any stuff on the product when the product works, it may influence the video quality. Do not cover any thing containing mental material on the product, because it may influence the signal strength.
WT-1041 3G Camera Real View Bottom View 3. TALKING THE FIRST STEP Your WT-1041 3G Camera is smart monitor device, which can only be used in 3G networks and can be set by message. Suggest being store the commonly used SMS command in your phone. Install USIM Card Before use, you must insert USIM card into WT-1041 3G Camera USIM card contains the number you want to dial WT-1041 3G Camera WT-1041 – User Manual – Rev.1.2 - Technical Support: technical@witura.
WT-1041 3G Camera Note: Before installing USIM card, please make sure that the power switch is set off. If you don’t insert USIM card, WT-1041 3G Camera will not work properly. At this moment, the green light will flash quickly (one time per 0.5 second). If you want to insert or pull out USIM card, please power off and disconnect the charger first. USIM socket is located on the bottom of the product. Please insert the USIM card as the arrow shows. After insert the USIM card, please switch USIM card.
WT-1041 3G Camera Note: Please do not pull the USIM card out when the charger is connected. When the product is powered on, it can detect that charger is inserted. At this time, the battery indicator lights red. If the battery indicator (red) flash quickly (per 0.5 second), it means that the power is low. When the power is low to some extent, the product will be powered off automatically. At this time, please plug in the charger and continue to use.
WT-1041 3G Camera 4. GETTING STARTED Host Number Setting 1) Insert a 3G SIM Card into the WT-1041 3G Camera Note: Before installing the SIM Card make sure that the power switch is set off. 2) Connect to charger Note: Do not pull the SIM Card out when the charger is connected When products is powered on, it can detect charger is inserted.
WT-1041 3G Camera >> Type following message via the phone: In English: set host “set host” your phone num 8888(original password) >> Sent the message to the to the SIM Card of the WT-1041 3G Camera >> If succeed it will reply the SMS “Set Host Number OK” or “Failed to Set Host Number” >> Now you can test by making a video call to the WT-1041 3G Camera and it will enter the monitor mode.
WT-1041 3G Camera 3. If succeed, WT-1041 3G Camera will return a message “Delete Share Number OK”, or it will return a message “Failed To Delete Share Number”. Delete All Share Numbers 4. Input the following message: In English: del all share*password 5. 6. Send the message to WT-1041 3G Camera If succeed, WT-1041 3G Camera will return a message “Delete all Share Number OK”, or it will a message “Failed to Delete All Share Number”. List All Share Numbers 7.
WT-1041 3G Camera Master Reset The Master Reset function allow to make the device return to factory settings, like clearing both the Host and Share numbers ready set in the device, and set the password to default 888888 as before; 1. Input the following message via phone: In English: Master Reset *Password 2. Send the message to WT-1041 3G Camera If succeed, WT-1041 3G Camera will return a message “Master Reset OK” 5.
WT-1041 3G Camera Note: If the video or audio recording is paused by the video call, the recording will continue after recording ends and is saved as another file different from the saved recording If the host makes a video call when WT-1041 3G Camera is taking photo, WT-1041 3G Camera will finish the photo taking and save it, and then get through the video call If the host or the share number sends the photo taking, video/audio recording order when WT-1041 3G Camera is in the course of video call,
WT-1041 3G Camera Begin Video Recording 1. Input the following message via the phone: In English: begin video rec 2. Send the message to WT-1041 3G Camera 3. If succeed, WT-1041 3G Camera will return a message “Video Recording Activated”, otherwise it will return a message “Failed To Activate Video Recording”. Begin Video Recording In Night Mode (When In Low Light) 1. Input the following message via the phone: In English: begin video rec m 2. Send the message to WT-1041 3G Camera 3.
WT-1041 3G Camera Note: Infrared mode can be used in no light environment. The distance with best effect for normal Infrared can reach is around 200 centimeters. Exposal will happen if the camera is too close to the target under Infrared condition, while or the other hand, too far away will lead the Infrared lose effect because of the mono color generated by Infrared light. Begin Infrared Video Recording In The Night Mode 1. Input the following message via the phone: In English: begin video rec mf 2.
WT-1041 3G Camera Note: During Video recording, 3G Camera will send the alert message to host if low power and will not give further warning if the Host doesn’t handle in time till 3G Camera lost all the power. After 3G Camera retrieve the power, it will continue to perform the Video Recording command and save the recorded data in two files. At the session, if the host number is changed, the previous Video Recording command still valid until the new host send the stop command.
WT-1041 3G Camera 3. If succeed, WT-1041 3G Camera will return MMS with photo format 800x600, or it will return a message “Photo Taking Failed”. If MMS sending fails, then it return a message “MMS Sending Failed”. Note: Night mode is applied in low light condition and used to increase the brightness to get the best taking effect. One-Time Infrared Photo Taking (No Light) 1. Input the following message via the phone: In English: take photo f 2. Send the message to WT-1041 3G Camera 3.
WT-1041 3G Camera 3. If succeed, WT-1041 3G Camera will return MMS with photo format 800x600, or it will return a message “Photo Taking Failed”. If MMS sending fails, then it returns a message “MMS Sending Failed”. Note: For above mentioned Photo Taking modes, If succeed, 3G Camera will return the MMS and the interval time depending on the network. Audio Recording The host and share number can begin/end audio recording via the message. Begin Audio Recording 1.
WT-1041 3G Camera Note: Video recording, photo taking and audio recording have the priority as follows: video recording> photo taking>audio recording. That is: 1. When the video recording activates, 3G Camera will neglect the message to activate the photo taking and audio recording. 2. When the photo taking activates, 3G Camera will neglect the message to activate audio recording, but response the message to activate video recording. 3.
WT-1041 3G Camera Note: When the memory is full, 3G Camera will send a memory full alert message to the host for one time. Low Power Capacity When the battery power is low, WT-1041 3G Camera will automatically send a message to the host:”Low power, Please Charge the Battery”. Delete Memory Date The host can delete the phone memory data via the message. 1. Input the following message via the phone: In English: Del memory*password 2. Send the message to WT-1041 3G Camera 3.
WT-1041 3G Camera Get Password Only the host number can get the password of WT-1041 3G Camera via the message. 1. Input the message via the phone: In English: Get password 2. Send the message to WT-1041 3G Camera 3. If succeed, WT-1041 3G Camera will return the password, example:888888 Help Because the above message are hard for us to remember, WT-1041 3G Camera offers the help function. 1. Input the message via the phone: In English: Help 2. Send the message to WT-1041 3G Camera 3.
WT-1041 3G Camera m. Take photo: take photo n. Take photo night mode: take photo m o. Take photo infrared mode: take photo f p. Take photo night & infrared mode: take photo mf q. Begin audio record: begin audio rec r. Begin audio record: end audio rec s. End audio record: Report status t. Command help: Help u. Delete memory: Del memory*password v. Delete T-card memory: Del tcard memory*password w. Get password : Get password x.
WT-1041 3G Camera 7. Troubleshooting Before you make a call to customer center, please refer to the following possible troubles. They may be helpful. Wrong Operation Prompt Possible reason Measurement Not insert USIM card. Please insert the USIM card. The inserted SIM card has PIN code or PIN2 Please unlock the PIN or PIN2 code in code. other phone.
WT-1041 3G Camera Battery Indicator Lights Red And Flash Quickly Possible reason Not connect the charger to the product correctly . Measurement make sure that charger Please has connected to the product correctly and insert the socket for at least 3 hours. Please close the power , disconnect the _____ charger and restart the product after 10 seconds. Message Fails To Feedback Possible reason _____ Measurement Please close the power , disconnect the charger and restart the product after 10 seconds.
WT-1041 3G Camera 8. GLOSSY 3G: The third generation wireless mobile communication system. 3G stands for the new generation wireless mobile communication system base on the seconds’ generation one. 3G system supports the real time communication service and highspeed data packet service. In Europe, 3G refers to the UMTS developed on the basis of GSM. PIN: The identity code offered by WT-1041 3G Camera. It can support the video call service. UMTS: The global mobile telecommunication system.