VERSION: 1.2 UPDATED: AUG 2013 WT‐1672B GSM Wireless Alarm System USER MANUAL WITURA TECHNOLOGY SDN BHD | WT‐1672B GSM Wireless Alarm System User Manual V2.
INTRODUCTION One of the most popular do‐it‐yourself home security solutions is the installation of a wireless alarm system. Affordable and easy to install, wireless systems are highly recommended to anyone who wants to avoid drilling into walls or who wants to bypass complicated wiring instructions without compromising security.
Step 1 ‐ The simplest set up methods to set up Administrator number Applied the “KISS Principle”, keep it simple, stupid. The GSM Remote Control Switch is easy to setup and use. Insert the SIM card, simply use your mobile phone call to the unit, your mobile phone number will automatically register as the 1st Administrators You will receive the following SMS message from the unit – Administrator: 1: 18617185300 (your phone number) 2: 3: 4: 5: You already finish the set up.
Factory Reset If you required to change the administrator number in the future, simply press the button “FACTORY” at the mother board until you hear the “du~” . This means the unit back to the factory default This means you already reset the unit to factory default. Now you can start to call again to set the administrator. This method of setting is only allowed to set 1 administrator number.
Step 2 ‐ Advance Set Up NO. Description 1 First Step of programming, you must enter the factory passwords of 1234 and go inside the programming mode. Programming Code *0*1234# SMS Texts Respond You get administrator privileges! 2013‐10‐09 00:33 Wed When you enter *0*1234#, you enter into the programming mode. You must perform the next command in 10 minutes. If you did not do anything, the system will exit from programming mode.
Check the relay status in ON or OFF Mode. *4* Master relay 2013‐10‐10 16:10 Thu 7 Check Signal Strength *5* CSQ<28> 2013‐10‐10 16:11 Thu The unit will return Master relay if the relay is on. The unit will return Master relay if the relay is off. You must confirm the signal strength at site before you install the unit. If the signal too weak, the unit will not function properly. CSQ 5 – 12 Signal too weak, system not function CSQ 13 ‐ 24 Signal Good.
11 Delete the list of Remote Control List in the system *9*N# Controller: 1:373f00 2: 3: 4: 5: N = 1 to 5 (N is numbering in the list of Remote Control in the system) For example, if you want to delete list no 2.
14 Main message switch *21*N# Message switch Main message switch 2013‐10‐10 17:06 Thu N=0 OFF N=1 ON 15 To receive SMS Reply Message or not to receive SMS Replay Message when the system trigger by phone call *22*N# After sending command *22*0# Status switch 2013‐10‐10 17:10 Thu： After sending command *22*1# Master relay 2013‐10‐10 17:08 Thu： 16 Security mode/ Open Mode *23*N# When Setting as Security Mode *23*1# Mode switch 2013‐10‐10 17:13 Thu When Setting as Open Mode *
18 Call alert to Admin Number when turn on / off the alarm equipment *25*N# When Setting as *25*5# Call switch: wireless alarm 2013‐10‐10 17:18 Thu N=0 means switch off all alarm alert, which means any alarm alert from the equipment, it will not call admin number when the N=1 means equipment is switch on, it will call admin number N=2 means when the equipment is power outage, it will call admin number N=3 means when the equipment is line cut trigger, it will call admin number N=5 means when the 9 channe
20 Check input messages programmed in the system and the 9 channels wireless alarm alert messages *27*NN# When Setting as *27*00# Startup user defined information: The equipment has already started! 2013‐10‐10 17:36 Thu When Setting as *27*01# Wireless 1 defined information: The door closed! 2013‐10‐10 17:40 Thu 21 Delete input messages programmed in the system and the 9 channels wireless alarm alert messages *28*NN# When Setting as *28*00# Delete OK! NN=00 means Check Input Alert Message for system
22 High / low alarm settings for Line Cut Alarm Alert *31*N# When sending *31*1# Line alarm: High level 2013‐11‐30 09:42 Sat N=0 means low alarm when Line Cut Alarm (which means connect the 2PIN at the J16 port) N=1 means high alarm when Line Cut Alarm (which means disconnect the 2PIN at the J16 port) Factory Default as N=0 where the 2PIN at the J16 port connected 23 Restart System *33* Restart System 24 Pairing Remote Control Press either 1 button at the Remote Control, and press Controller butt
Step 3 ‐ Installation Insert the SIM card, to access the SIM card carrier gently push the button adjacent to it, insert the SIM card and carefully close the carrier Connect the cable to terminals 220V & N ensuring positive is connected to terminal 200V, switch on the power supply , the red power LED will light indicating power is present, the blue network LED indicator will initially flash quickly, once logged onto the network , it will flash more slowly approximately one every 3 ‐4 seconds It is recommend
Example Wireless And Wireless Sensor with WT‐1672B Production Specifications Operation Voltage Operating Current Relay Contacts GSM Frequency MHz Humidity Operating Temperature Physical Size Protection Approvals WITURA TECHNOLOGY SDN BHD | 12 volts DC Maximum 500mA, typically 55mA 2amps GSM900/1800Mhz, or GSM850/900/1800/1900Mhz Less Than 80% RH ‐20c to 55c 6.8cm x 4.1cm x 12.5cm IP 65 Weather Proof Casing C.E, FCC, ETSI WT‐1672B GSM Wireless Alarm System User Manual V2.
Preparing the SIM card All new SIM cards have to be registered with the network provider before they can be used, usually by calling the network provider or registering on their website please refer to the instructions supplied with your SIM card. During the registration procedure a confirmation code or text message is usually sent to the SIM cards telephone number, to be able to read and react to the message you will need to insert the SIM card into an unlocked mobile phone.
Troubleshooting Ensure that your DC power supply is connected 1. Red power LED not alight correctly, positive (+) to terminal 220v and negative (‐) to terminal N. Verify 12 volts is present using a volt meter Ensure your SIM card has been activated and that the 2. Blue network LED flashing every one second PIN request has been disabled.
Warranty Witura Technology Sdn Bhd warrantees the WT‐1672B GSM Wireless Alarm System against defective parts and workmanship. Witura Technology Sdn Bhd shall, at its option, repair or replace the defective equipment upon the return of such equipment to any Witura branch.
