User Manual ---Apply to R200/R520 Industrial 3G/4G Router V3.0 http://www.wlink-tech.
Industrial Cellular Router User Manual Copyright © Shenzhen Wlink Technology Company Limited 2012 ～ 2014 Without our written approval, Anyone can’t extract, copy whole or part of content of this file and can’t spread out in any format. Caution Due to product updates or functional upgrading, we may renew the content of this file, and this file only for reference. All statement, information, suggestion.
Industrial Cellular Router User Manual Contents 1 Product Introduction..................................................................................................................... 4 1.1 Product overview................................................................................................................4 1.2 Model introduction..............................................................................................................4 1.3 Product Appearance...............................
Industrial Cellular Router User Manual www.wlink-tech.
Industrial Cellular Router User Manual 1 Product Introduction 1.1 Product overview Wlink industrial Router use industrial grade design, high-powered 32bit MIPS network processor, embedded industrial grade, high powered, multi-band frequency mobile 3G+ communication module, support WCDMA, HSPA+、TD/FDD-LTE、EVDO（CDMA 2000） etc.
Industrial Cellular Router User Manual Table 1-1 Router model table www.wlink-tech.
Industrial Cellular Router User Manual www.wlink-tech.
Industrial Cellular Router User Manual 1.3 Product Appearance Table 1-2 Wlink Router Appearance Series R200 R200－W（G） R520－（G） R520－D Appearance Ports Product 1*LAN 1*LAN + 1*WAN + 1*WAN + 4*LAN + 1*WAN + 4*LAN + 1*WAN GPS or WLAN(11n 1T1R) GPS or WLAN(11n 1T1R) single module/doulbe SIM, double module/double SIM Single port router Single port Wi-Fi（GPS）router Multi-port Wi-Fi router multi-port double-link router category 1.
Industrial Cellular Router User Manual Figure 1-1 Network Topology Wlink industrial router is based on mobile wireless public network or private network, build wireless data channel in mature network, to lower down the cost of wireless data transmission and technique. 1.5 Features Various cellular module optional, LTE/HSPA+/EVDO/CDMA2000 optional Support IEEE802.11b/g/n Wi-Fi AP function, extended support to Wi-Fi terminal, WDS bridging, support WEP, WPA/WPA2 Personal/Enterprise, TKIP/AES, etc.
Industrial Cellular Router User Manual 2 Hardware Installation This chapter is mainly for installation introduction, there would be some difference between the scheme and real object. But the difference doesn’t have any influence to products performance. 2.1 Panel: Table 2-1 WLR200 -Structure Wlink Tech. R200 series Front Rear Table 2-2 WL-R520 Structure Wlink Tech. R520 series Front Rear www.wlink-tech.
Industrial Cellular Router User Manual There are some different for Antenna interface and indicator light for the expanded Wi-Fi, GPS series. Table 2-3 Router Interface Port Instruction Remark USIM Plug type SIM Slot, support 1.
Industrial Cellular Router User Manual silk-screen LAN color status Indication Green Dark WLAN port isn’t opened Green Solid light connect ok Green Blinking Data Sending Green Dark Not connected There are some difference among the LED indicator of expanded Wi-Fi, GPS function and single module/double SIM, double module/double SIM series products. 2.3 Dimension Figure 2-2 R200 Series Router Dimension Figure Figure 2-3 R520 Series Router Dimension Figure www.wlink-tech.
Industrial Cellular Router User Manual 2.4 How to Install 2.4.1 SIM/UIM card install If use dual SIM/UIM card router, you may need insert dual SIM before configure it. After installation, please follow below steps to connect the router. Before connecting, please disconnect any power resource of router 2.4.2 Ethernet Cable Connection Use Ethernet cable connect the cellular Router and computer directly, or transfer by a switch. 2.4.
Industrial Cellular Router User Manual 3 Router Configuration This Chapter introduces the parameter configuration of the router, the router can be configured via web internet explorer, or Firefox, chrome. We take GUIs 7 system and Internet Explorer 9.0 as sample. 3.1 Local Configure The router supports configurated by local Ethernet port, You could specify a static IP or DHCP get IP for your computer. The default IP address is 192.168.1.1，subnet mask is 255.255.255.
Industrial Cellular Router User Manual User should use default user name and password when log in for the first time Figure 3-5 User Identify Interface ----END 3.2 Basic Configuration Different software version have different web configuration interface, below take R20 2.6.0.1 version as example. After visit the WEB interface, you can check the current status of Router, or modify router’s configuration via web interface, below is the introduction for the common setting. www.wlink-tech.
Industrial Cellular Router User Manual Figure 3-6 Router Status GUI 3.2.1 Cellular Network Configure Step 1 Single Click Basic Network-> Cellular, you can modify relevant parameter according to the application. www.wlink-tech.
Industrial Cellular Router User Manual Figure 3-1 Cellular Settings GUI Table 3-1 Cellular Setting Parameter Instruction Parameter Instruction Enable Enable SIM card dial ICMP check To enable or disable ICMP check rules. Enable the ICMP check and setup a reachable IP address as destination IP. Once ICMP check failed, router will switch SIM card.
Industrial Cellular Router User Manual 【SIM2 Only】Just SIM2 is available. 【Backup】SIM1 is the primary SIM. Once SIM1 is failed, it will switch to SIM2 and work on SIM2 within the defined time. Once the time is over, it will switch back to SIM1. Step 2 After Setting, please click “save” icon. ----End 3.2.
Industrial Cellular Router User Manual parameter Instruction IP Address Range IP address range within LAN Lease The valid time Step 2 After setting, please click “save” to finish, the device will reboot. ----End www.wlink-tech.
Industrial Cellular Router User Manual 3.2.3 Dynamic DNS Setting Step 1 Single click “ Basic Network->DDNS to open the DDNS setting GUI. Figure 3-4 Dynamic DNS Setting Table 3-3 DDNS Setting Instruction parameter Instruction IP address Default is standard DDNS protocol. for customized protocol, pls contact our engineer. Usually, use default IP 0.0.0.
Industrial Cellular Router User Manual Figure 3-5 WLAN Basic Settings GUI Table 3-4 Basic Setting Instruction Parameter Instruction Enable wireless Enable or Disable the Wireless Wireless mode Support AP, AP+WDS, Bridge, Client, WDS Wireless Network protocol Support Auto, IEEE 11b/g/n selectable SSID The default is router, can be modified Channel The channel of wireless network, suggest keep the default Channel Width 20MHZ and 40MHZ alternative Security Support various encryption method Ste
Industrial Cellular Router User Manual Figure 3-6 Wireless Client Filter Setting GUI The Wireless Filter enable to set the permitted client or prohibit the specific client to connect the WiFi, However, this feature is invalid for wired connection application.
Industrial Cellular Router User Manual Figure 3-7 Port Forwarding GUI Table 3-6 “Port Forwarding” Instruction parameter Instruction Proto Support UDP, TCP, both UDP and TCP Src. Address Source IP address. Forward only if from this address. Ext. Ports External ports. The ports to be forwarded, as seen from the WAN. Int. Port Internal port. The destination port inside the LAN. If blank, the destination port is the same as Ext Ports.
Industrial Cellular Router User Manual Figure 3-8 DMZ GUI Table 3-7 “DMZ” Instruction parameter Instruction Destination Address The destination address inside the LAN. Source Address If no IP address inside, it will allow all IP address to access. Restriction If define IP address, it will just allow the defined IP address to access. Leave Remote Access Step 2 Please click ”save” to finished ----End 3.4.
Industrial Cellular Router User Manual Figure 3-9 Firewall Setting GUI Table 3-8 “Firewall” Instruction parameter Instruction Applies To White list. Blocked Resources Black list. Step 2 Please click ”save” to finished 3.4.4 GPS Setting Step 1 Please click “Advanced Network> GPS” to view or modify the relevant parameter. www.wlink-tech.
Industrial Cellular Router User Manual Figure 3-10 GPS Setting GUI Table 3-9 “GPS” Instruction parameter Instruction Bind Port Local port for GPS data. Server IP and Port GPS server IP address and port. Socket type GPS data protocol. Socket Timeout The timeout for socket connection. If socket is not established, it will reconnect after the timeout time. Serial Timeout No serial port data, GPS module will send GPS data after the timeout time. Packet Payload The max packet for GPS data.
Industrial Cellular Router User Manual Figure 3-11 GRE Setting GUI Table 3-10 “GRE” Instruction parameter Instruction Remote IP Address GRE peer IP address. Usually a public IP address Local IP Address Local IP address for LAN. Tunnel Local IP address GRE Tunnel local IP address which is a virtual IP address. Remote LAN IP Address GRE Tunnel remotel IP address which is a virtual IP address. ICMP Check IP Address It’s a reachable IP address. Once the ICMP check is failed, GRE will re-established.
Industrial Cellular Router User Manual parameter Instruction Password As the configuration requested. Encryption As the configuration requested. Stateless MPPE As the configuration requested. Accept DNS As the configuration requested. Remote Subnet As the configuration requested. Create NAT on Tunnel As the configuration requested. Step 2 Please click ”save” to finished. 3.6 System Management 3.6.
Industrial Cellular Router User Manual parameter Instruction the domain of WAN, no need to configure for most users. Step 2 Please click ”save” to finished ----End www.wlink-tech.
Industrial Cellular Router User Manual 3.6.2 Time configuration Step 1 Please click “Administrator> time” to view or modify the relevant parameter. Figure 3-13 System Configuration GUI If the device is online but time update is fail, please try other NTP Time Server. Step 2 Please click “save to finish. ----End www.wlink-tech.
Industrial Cellular Router User Manual 3.6.3 Admin Access Setting Step 1 Please click “Administrator>Admin” to view and modify relevant parameter. In this page, you can configure the basic web parameter, make it more convenient for usage. Please note the “password” is the router system account password. Figure 3-14 Admin Setting GUI Step 2 Please click save iron to finish the setting ----End www.wlink-tech.
Industrial Cellular Router User Manual 3.6.4 Backup Setting Step 1 Please click “ Administrator> Back up Configuration ” to do the backup setting Figure 3-15 Backup and Restore Configuration GUI Restore Default would be lose all configuration information, please be careful. Step 2 After setting the backup and restore configuration. The system will reboot automatically. ----End www.wlink-tech.
Industrial Cellular Router User Manual 3.6.5 System Log Setting Step 1 Please choose “Administrator> Logging” to start the configuration, you set the file path to save the log (Local or remote sever). Figure 3-16 System log Setting GUI Step 2 After configure, please click “Save” to finish. ----End www.wlink-tech.
Industrial Cellular Router User Manual 3.6.6 Firmware upgrade Step 1 Please click “Administrator>firmware upgrade” to open upgrade firmware tab. Figure 3-17 Firmware Upgrade GUI When upgrading, please don’t cut off power of router. 3.6.7 System Reboot Step 1 Please click “Administrator>Reboot” to restart the router. System will popup dialog to remind “Yes” or “NO” to carry out the operation.
Industrial Cellular Router User Manual 3.7 “RST” Button for Restore Factory Setting If you can’t enter web interface because of other reasons, you also can use this way. For R200 Series, “RST” button is on the left or Ethernet port, for R520 Series, the button is on the left of NET light. This button can be used when the router is in use or when the router is turned on. Press the “RST” button and keep more than 8 second till the NET light stopping blink. The system will be restored to factory.
