5G Internet Gateway Outdoor Mounting Kit Installation Guide (LV55IHP) Version 1
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
RF Exposure Statement To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons (indoor), at least 54cm from all persons (outdoor), and must not be co-located or operating in conjunction with any other antenna or transmitter. Safety Warnings Adapter Do not use any other power adapter except the one that accompanies this unit or a power adapter identified in the list below.
Table of Contents Chapter 1 Introduction ..................................................................................................................................... 1 1.1 Unboxing Information........................................................................................................................... 1 1.2 Key Features ......................................................................................................................................... 1 1.
Chapter 1 Introduction Verizon’s 5G Internet Gateway provides Verizon’s customers with a better solution for 5G home service. The innovative design of the 5G Internet Gateway allows customers to connect their favorite devices to Verizon’s 5G/LTE Network. 1.
1.3 Bottom Panel (without Enclosure) RJ45-Outdoor LED-Outdoor Part Description RJ45-Outdoor Connect the Gateway to the surge protection unit (SPU) via an Ethernet cable. LED-Outdoor The LED will light up in different ways to indicate the connectivity status of the 5G Internet Gateway.
1.4 Bottom Panel (with Enclosure) 1.
1.6 LED Notification Guide Status Bottom LED Device is powering up Soft fade in-out blue Bluetooth® pairing mode (INSTALLATION MODE) Pairing starts automatically once the device is powered on. Bluetooth® is paired LED stops blinking blue Activation complete (INSTALLATION MODE) The device has successfully activated and established an LTE connection, and will start searching for a 5G signal. No 5G signal (INSTALLATION MODE) The Gateway did not immediately detect a 5G signal after activation.
Chapter 2 Installing the 5G Internet Gateway This section describes how to install the 5G Internet Gateway in an outdoor configuration, which is adopted when the indoor configuration is unable to detect a usable 5G signal. Outdoor installations must be carried out by professional, trained technicians. 2.1 Ground Installation Step 1: Pry off the I/O cap covering the bottom of the Gateway’s mounting collar. Step 2: Unscrew the four M2 screws securing the mounting collar to the Gateway.
Step 3: Grab the front end of the collar and pull it off the Gateway. Step 4: Use a screwdriver to press down on the two snap-fits pictured below to allow the front cover to be removed from the Gateway.
Step 5: Pry off the front cover (the side with the logo) of the Gateway. Step 6: Place the Gateway into the waterproof enclosure. Make sure the side with the connectors is aligned with the side of the enclosure with the cable access hole.
Step 7: Install the rear cover of the waterproof enclosure. Make sure the pole slot on the rear cover is aligned with the side of the enclosure that has the cable access hole.
Step 8: Latch the protruding side of the four side covers of the waterproof enclosure to the rear cover, then press downward on the side covers until a secure fit is achieved. Step 9: Use four screws to securely affix the side covers to the enclosure.
Step 10: Take one end of an Ethernet cable and run it through the cable gland parts in accordance with the image below. Step 11: Plug the Ethernet cable mentioned in the previous step into the RJ45-Outdoor port of the Gateway. Step 12: Use a wrench to secure the screwing gland to the cable access hold of the enclosure. Tighten the screwing gland to 25–27 kgf-cm torque. Step 13: Wedge the seal gasket and clamp ring into the screwing gland.
Place the seal cap over the clamp ring, then use a wrench to tighten the seal cap to 15 kgf-cm torque. Step 15: Place the enclosure on a suitable location on the ground. 2.2 Wall Installation Step 1: Once you have completed steps 1 to 12 in section 2.1, find a suitable installation location on the wall. Step 2: After the aforementioned location has been found, use four screws to affix the wall mounting bracket to the wall.
Step 3: Adjust the mounting pole until the desired angle is achieved, then tighten the hinge screws on the pole to 100 ± 10 kgf-cm torque. Note: Use a spirit level to ensure that the mounting pole is perpendicular to the ground.
Step 5: Once the pole is in the slot, place two M10-1.5 screws into the screw holes shown in the image below, then tighten the screws to 60 ± 10 kgf-cm torque. Step 6: Use the cable management clips on the mounting pole and wall mounting bracket to route the Ethernet cable (refer to images below).
Step 7: Use a M4-0.7 screw to attach the grounding cable to the rear cover of the enclosure. Tighten the screw to 10 kgf-cm torque. Step 8: Route the grounding cable through the cable management clips on the pole (refer to the image below).
Step 9: Place the plastic bracket cover over the wall mounting bracket (refer to the image below). Make sure the cables are going straight down. Step 10: Check the LED indicator on the Gateway to make sure it is functioning normally.
Chapter 3 Connecting the 5G Internet Gateway This section describes how to set up and configure your 5G Internet Gateway. 3.1 Setting up the 5G Internet Gateway 1. Complete the steps in section 2.1 of chapter 2 (if installing the Gateway on the ground) or the steps in section 2.2 of chapter 2 (if installing the Gateway on a wall). 2. Plug the Ethernet cable coming from the Gateway into the Ethernet port on the surge protection unit (SPU). 3. Use an Ethernet cable to connect the SPU to a Router. 3.
Chapter 4 Product Specifications 1. 5G 5G n260/n261 5G n2/n5/n66 4G LTE CAT16, Band 2/4/5/13/48/66 IoT Bluetooth® 5.0 Memory CPE: DDR4 RAM 1GB Storage CPE: NAND 1GB Dimensions 265 x 265 x 100 mm 265 x 265 x 145.57 mm (with rear cover) Weight 4.8 Kg Connector 2.
