5G Internet Gateway User Guide (LV55IHP) Version 6 Section 2.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
RF Exposure Statement To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons (indoor), at least 48cm from all persons (outdoor), and must not be co-located or operating in conjunction with any other antenna or transmitter. Safety Warnings Adapter Do not use any other power adaptor except the one that accompanies this unit or a power adaptor identified in the list below.
Table of Contents Federal Communication Commission Interference Statement ............................................................... i RF Exposure Statement .............................................................................................................................. ii Safety Warnings ............................................................................................................................................ ii Caution ....................................................
Chapter 1 Introduction Verizon’s 5G Internet Gateway provides Verizon customers with an improved solution for 5G home service. The innovative design of the 5G Internet Gateway allows customers to connect their favorite devices to Verizon’s 5G Network.
Bottom and Side Panel Side panel LED ● Multipurpose sync button Bracket Bottom panel RJ45 Ethernet port DC jack Reset pin hole Part Description LED The LED lights up in different ways to indicate the connectivity status of the 5G Internet Gateway. Multipurpose Press this button once to connect the 5G Internet Gateway to Wi-Fi Extender sync button or Wi-Fi Extender Mini devices via WPS or Bluetooth®. After the pairing is successful, the LED light will stop blinking blue.
LED and Audio Behavior Status Front LED Device is booting up Sound Not Applicable Soft Fade in-out White Bluetooth® pairing mode Not Applicable (Default-automatic) Starts automatically when power is on Bluetooth® pairing mode Not Applicable (Manual option) Single press the multifunction sync button to establish connection WPS/Bluetooth® is paired Click sound Blue blinking ceases Plays once immediately after establishing connection Activation completed Click sound INSTALLATION MODE Plays once
Passing 5G signal Good signal INSTALLATION MODE sound Good 5G signal has been detected for Plays once installation. immediately after switching to operational mode and finding passing signal Firmware update/Factory reset in Not Applicable progress Error (Fault) Error sound Hardware or software issue INSTALLATION MODE Plays once immediately after incident Not Applicable Working as advertised REGULAR USAGE MODE Device setup is completed and Internet is active.
Chapter 2 Self-Setup and Activation Installation, Activation, and Setup Please download the My Verizon Mobile app for installation, activation and setup of your 5G Internet Gateway. Take out the set up guide print from the gift box. Back side Front side This side should be printed with URL/QR code Please do not remove anything from the box yet. Scan the QR code to visit the URL on your mobile device or access http://setup.verizon.
When installing the 5G Internet Gateway, make sure that the back side of the device faces towards the direction of the 5G signal. Back side: Front side: This side should face the 5G signal This side should face inside the home.
WPS Connection WPS can be used to pair your 5G Internet Gateway to the Wi-Fi Extender or Extender Mini by following these steps: 1. Short press the multipurpose sync button on your 5G Internet Gateway. 2. Short press the multipurpose sync button on the Wi-Fi Extender or Extender Mini, making sure the device is within range of the 5G Internet Gateway. 3. The 5G Internet Gateway will play a sound to indicate pairing success.
Chapter 3 Accessing the Web User Interface Login After connecting and turning on the 5G Internet Gateway, a Sign In screen will appear. Enter your admin password to log into the Home Page of the 5G Internet Gateway’s Web GUI. If you forget your password, you can answer one of the security questions to reset the password to factory default settings. You can find the default password on the label under the 5G Internet Gateway.
Home Page/Main Section After logging in, the Home Page of the 5G Internet Gateway will appear. The Home Page is where users can check the connection status between the 5G Internet Gateway and the Internet/mesh network, conduct network speed tests, and adjust settings such as Wi-Fi options, parental controls, and more. In the upper right panel of the screen, the Network Map presents a list of devices that are currently connected to the 5G Internet Gateway.
3.2.1 Network Map (Speed test, Mesh network) The Network Map is located in the upper-right section of the Home Page. The lines between the 5G Internet Gateway and the Internet/mesh network/devices on the map indicate the connection status between them. A solid green line indicates a wired connection, a dashed line indicates a Wi-Fi connection, and a gray line with a red x in the middle indicates that there is no connection.
In the Security Questions section, you can choose three security questions, then enter the answer for each question. If a user forgets his/her admin password, one of the questions will be used to revert the admin password to factory default settings. Click Save to save your changes. Click Close to close the Admin Settings window. 3.2.3 My Verizon You will be directed to My Verizon, where you can manage your account online.
Wi-Fi Settings Click the > arrow on the bottom-right side of the Wi-Fi column in the Home Page to bring up the Wi-Fi page. On this page, you can adjust settings for the Primary Wi-Fi Network, Guest Wi-Fi Network, WiFi Advanced Settings, and WPS.
3.3.1 Primary Wi-Fi Network Slide the Enable switch to the right to activate the Primary Wi-Fi network. The switch will turn blue to indicate that the selected Wi-Fi network is turned on. To turn off the Primary Wi-Fi network, slide the switch to the left.
1. Wi-Fi name (SSID) The Wi-Fi name (SSID) is the name of the wireless network broadcasting from the 5G Internet Gateway. In order for devices to connect to the local network over a wireless link, they must select this network name from the list of detected wireless networks in the area. 2. Password Specify a password for your wireless network. Click the icon to display the selected password for the SSID. 3. New Password Enter a new password here for the SSID. 4.
3.3.2 Guest Wi-Fi Network Slide the Enable switch to the right to activate the Guest Wi-Fi network. The switch will turn blue when the guest network is enabled. To turn off the Guest Wi-Fi network, slide the switch to the left. 7. Wi-Fi name (SSID) The Wi-Fi name (SSID) is the name of the wireless network broadcasting from the 5G Internet Gateway.
11. Broadcast Wi-Fi Name (SSID) Check the box if you want to broadcast the SSID. The SSID will be displayed when you search for available networks. 12. Wi-Fi network encryption Select one security method from the drop-down menu. The encryption types include None, WEP-64, WPA2-Personal, and WPA-WPA2-Personal. 3.3.3 Wi-Fi Advanced Settings 13. Wi-Fi Network Operation Mode On this page, you may adjust the operation mode, channel, and bandwidth for the 5 GHz and 2.
14. Airtime Allocation Slide the Enable switch to the right to activate this function. The switch will turn blue when airtime allocation is enabled. To disable airtime allocation, slide the switch to the left. When ATF is enabled, the system needs to be restarted for it to take effect. In the Airtime Allocation Policy pull-down menu, two policy options are available: Fair and Strict.
3.3.4 WPS 16. Primary Wi-Fi WPS WPS allows rapid wireless connection between the 5G Internet Gateway and other WPS-compatible devices. You can trigger the WPS function on Primary Wi-Fi by clicking on the Primary Wi-Fi WPS button.
Connected Devices This section displays information about the devices connected to the APs, illustrated through a Network Map, as well as the AP list and Connected Devices table. 3.4.1 Network Map The Network Map illustrates the mesh network comprising the connected APs, their names, as well as their respective connection status. The number in the circle indicate the number of clients currently connected to the AP. 3.4.
3.4.3 Connected Devices The name of each device that has been connected/is currently connected to the 5G Internet Gateway is displayed here. Also displayed are the health of their connection status, their IP addresses, which AP a device is connected to, and the restriction policies related to each device (if any).
The Delete Device button enables you to remove the selected device which has connected to the 5G Internet Gateway. Once removed, the computer/device will not be displayed on this page. The Block Device switch allows you to block or allow computers or devices from establishing a connection to the 5G Internet Gateway. To block a device, slide the Block Device switch to the right. The switch will be blue when the feature is enabled.
This section enables you to set restriction policies for the selected device. You can specify the time during which the selected device will not be able to access Internet. Alternatively, you may also specify the time during which the selected device will be able to access Internet. The settings you can perform in this section include the name of the schedule and the time period for the restriction policy. Click Save to save your settings. The permanently.
3.5.1 Port Forwarding Port Forwarding can be used to open certain ports of a device to communicate with an Internet service. To turn on Port Forwarding, slide the Port Forwarding switch on the bottom right of the General Information page to the right. The switch turns blue to indicate that the function is turned on. To turn off this function, slide the switch to the left. To access this page, click Port Forwarding on the General Information page.
Choose the protocol to be used for port forwarding. 20. IP Address The local server’s IP address. 21. To Port Type the value of the LAN port to which you want to receive the forwarded packets. Configured Ports This table displays the ports that have been configured. 22. Application The created rule name will be displayed here. 23. Port From This shows the value of the start port. 24.
This shows the protocol selected for the corresponding port forwarding rule. 25. IP Address This shows the local server’s IP address. 26. Port To This shows the value of the end port. 27. Enabled The icon indicates that the corresponding port forwarding rule has been enabled. 28. Remove Click on the x icon to delete a port forwarding rule. 3.5.
Parental Controls By creating Internet access policies, Parental Controls allow you to control and monitor Internet access. Parental Controls can be activated on the Home page by sliding the Filters switch in the Parental Controls column. You can also enable or disable the function after you enter the Parental Controls page. Slide the Parental controls switch to the right. When the switch is blue, parental control of websites and devices is enabled. To turn off this function, slide the switch to the left.
System Settings Internet Gateway 3.7.1 General Information The General Information page provides device information on the 5G Internet Gateway, including the device name, IMEI, model, and more.
3.7.2 History Log The History Log page provides various activity records of your 5G Internet Gateway. To access this page, click History Log on the General Information page. 3.7.
The Backup & Restore page covers functions for backing up/restoring the settings on your 5G Internet Gateway and resetting it to factory settings. To access this page, click Backup & Restore on the General Information page. 3.7.4 LAN Settings The LAN Settings page includes settings to configure advanced LAN settings (e.g., IP address, Subnet mask, DHCP) for your 5G Internet Gateway. To access this page, click LAN Settings on the General Information page.
The subnet mask along with the previously configured IP address defines the network. The default value for subnet mask is 255.255.255.0. 31. DNS Server Use this function to toggle whether the DNS server is set automatically or manually. DHCP DHCP assigns LAN IP addresses for connected devices. You can specify the range of IP addresses the 5G Internet Gateway may assign to devices. Click the DHCP switch to turn the DHCP function on or off.
Diagnostic You can perform a throughput test between two APs here. Select AP1 and AP2 and click the Run button to begin the throughput test. The results will be displayed in the Results section, which also shows Ping, throughput from AP1 to AP2 and vice versa.
Chapter 4 Product Specifications 5G n260/n261 5G n2/n5/n66 4G LTE CAT16, Band 2/4/5/13/48/66 Wi-Fi 2.4GHz 802.11ax 2x2 MIMO 5GHz 802.11ax 4x4 MIMO Backward compatible with 11ac/11n/11b IoT Bluetooth® 5.0 Memory 5G Internet Gateway: DDR4 RAM 1GB Router: DDR4 RAM 1GB 5G Internet Gateway: NAND 1GB Router: NAND 1GB Dimensions 220 x 220 x 86 mm Weight 1.9 KG Connector 2.
Appendix Installation Guide Operational Communication Signal 33
Self-installation - Quick Start Guide Initial Installation Step 1 – Attach the bracket to the 5G Internet Gateway before plugging in the power cable.
Step 2 & 3 – Attach the power cable to the AC adapter and plug the cable into an electrical outlet.
Boot up & Paring LED indicator will turn soft fade in-out White. Signal Scanning Hold the 5G Internet Gateway close to the window to perform signal scanning.
Step 1 – Confirm the signal orientation.
Window Installation Step 1 – Use window wipes to clean the chosen installation location. Step 2 – Press the bracket for 30 seconds to make sure that it is fully adhered to the window.
Step 3 – Adjust the angle of your 5G Internet Gateway.
Turn the tab at the bottom to lock the 5G Internet Gateway in a specific angle.
