30" HEAVY DUTY MISTING OSCILLATION WALL FAN ITEM NO.: FAN-OW30M 120V / 60Hz, 2A READ & SAVE THESE INSTRUCTIONS Questions, problems, missing parts? Before returning the product, please e-mail our customer service by hicfm@outlook.
READ AND SAVE THESE INSTRUCTIONS To prevent serious injury or property damage, read and understand owner's manual before operating. This prodct can be used indoor or outdoor with a proper GFCI plug. SAFETY INFORMATION 1. Unplug the fan before moving it or performing maintenance. Don't operate the fan when your hands are wet. 2. Do not disassemble, repair or rebuild the fan. 3. Unplug the fan when it is not in use. 4. Do not unplug the fan by holding the cable cord. Unplug by holding the plug. 5.
ASSEMBLY INSTRUCTION 1. Mark the mounting hole locations by using the holes in the bracket as a guide, then drill the holes. A. For concrete wall installation, after drilling, you would insert the wall anchors and tap them flush with the wall, position the bracket and then screw the two bolts into the anchors, securely attaching the bracket to the wall. B.
ASSEMBLY INSTRUCTION 3. Remove four sets of hexagonal nuts, spring washers, and flat washers from the motor, save them for step 4. 4. Set the rear guard in the proper position and affix it to the motor using the hexagonal nuts, spring washers, and flat washers.
ASSEMBLY INSTRUCTION 5. Assemble the fan blade onto the motor shaft by tightening the two screws. Make sure the crews are tightly secured. 6. Attach t he front guard to the rear guard and secure them together by using the clips on the front guard.
ASSEMBLY INSTRUCTION 7. Secure the assembly on the front guard and rear guard by tightening the screw, washer and nut at the bottom of the fan guards. 8. Insert the swivel bracket into motor Z brackets and fasten it with bolt (a), flat washer (b), spring washer (C) and nut (d). Fasten the bolt (f) with the knob (e) for adjusting the tilt angle of the fan or fix the tilt angle of the fan.
ASSEMBLY INSTRUCTION 9. Assemble the swivel bracket with wall bracket and fasten with hexagon screw, flat washer, spring washer and nut. 10. Loosen the knob (g) and adjust until the fan head is at the desired angle. Tighten the knob (g) back.
ASSEMBLY INSTRUCTION 11.Connect the misting switch (1) to the water pipe (2) and tighten it. Turn the switch (open) to open the misting function. Turn the switch (close) to close the misting function. ② ① Loose 3/4" Water Pipe Terminal 3/4"-11.5 External Thread 3/4"-11.
OPERTATING INSTRUCTIONS 1. Test GFCI(Ground Fault Circuit Interrupter) plug BEFORE EACH USE. Plug GFCI into power outlet. Press RESET button(b). Indicator(a) should turn red. Press TEST button(c). Indicator (a) should turn off. GFCI plug is tripped. DO NOT USE FAN IF ABOVE TEST FAILS. Call customer service for aaaistance.
CARE AND MAINTENANCE Unplug the appliance before cleaning. Don’t use any water for cleaning metal surfaces. Slightly moisten a cloth and then wipe off the surfaces of the fan. In order to remove dust from the grill, use a vacuum cleaner or remove the front grill by removing the securing screws on the edge of the grill. After cleaning, remount the grill. After doing this, fasten the screws on the edge of the grill.
Installation -- Secondary Safety Support Cable Warning: Use of secondary safety support cable does not guarantee protection against injury of persons. Mounting of both the circulator and cable could fail if subject to abuse, neglect or if improperly installed. To avoid personal injury, circulators must be supported anytime angle is adjusted. Secondary Support Cable Wall, Ceiling or Post Bracket PARTS SPECIFICATION QTY Φ3*3050 1 M5*13 2 ST8*50 1 Φ8*Φ24*δ2 1 Φ10*60 1 3.
