Speed Oven Installation Guide SPECIFICATIONS, INSTALLATION, AND MORE
Speed Oven Contents Important Note 3 Speed Oven To ensure this product is installed and operated as safely and efficiently as possible, take note of the following types of highlighted information throughout this guide: 4 Specifications 8 Installation 9 Troubleshooting Features and specifications are subject to change at any time without notice. Visit wolfappliance.com/specs for the most up-to-date information. IMPORTANT NOTE highlights information that is especially important.
Speed Oven Product Information Important product information, including the model and serial number, are listed on the product rating plate. The rating plate is located on the lower left side of the front face frame. The oven door must be open to view the rating plate. Refer to the illustration below. If service is necessary, contact Wolf Factory Certified Service with the model and serial number.
Specifications Installation Requirements The speed oven can be installed in a standard or flush inset application. INSTALLATION REQUIREMENTS BASE SUPPORT MIN Finish the edges of the opening. They may be visible when the door is open. 24" (610) Model 30" (762) Model 125 lb (57 kg) 125 lb (57 kg) For standard installations, the face trim will overlap stiles and rails. Refer to the chart. TRIM OVERLAP For flush inset installations, a minimum 1/8" (3) reveal is required on all sides.
Specifications Electrical Requirements Installation must comply with all applicable electrical codes. Locate the electrical supply as shown in the illustrations on the following pages. The receptacle may also be located in an adjacent cabinet within reach of the power cord. A separate circuit, servicing only this appliance is required. A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation. Refer to the illustration below for minimum power cord plug clearance.
Specifications Speed Oven STANDARD INSTALLATION 23" (584) OPENING DEPTH TOP VIEW E 17 11/16" (449) OPENING HEIGHT W OPENING WIDTH SIDE VIEW FRONT VIEW NOTE: 24" (610) and 30" (762) models require the same opening dimensions. OPENING WIDTH W 24" Model 221/8" (562) 30" Model 221/8" (562) 6 | Wolf Customer Care 800.222.
Specifications Speed Oven FLUSH INSET INSTALLATION 7/8" (22) 24" (610) FLUSH INSET DEPTH FINISHED CLEATS* TOP VIEW E 5/16" (8) 18 1/8" (460) FLUSH INSET HEIGHT** A 1/8" (3) W FLUSH INSET WIDTH** SIDE VIEW FRONT VIEW *Will be visible and should be finished to match cabinetry. **Dimension provides minimum reveals. FLUSH INSET WIDTH W A 24" Model 233/4" (603) 13/16" (21) 30" Model 301/8" (765) 4" (102) wolfappliance.
Installation Installation 1 Turn off power to the electrical outlet. 2 Move the unit near the opening. Remove and recycle packing materials. 3 The 30" (762) model is shipped with two shipping brackets located on each side, behind the front face. Remove both brackets, then reinstall the screws. Refer to the illustration below. 4 Plug the power cord into the grounded outlet. 5 Position the oven in the opening and slide back until the mounting flange is flush with the face of the cabinet.
Troubleshooting Troubleshooting IMPORTANT NOTE: If the speed oven does not operate properly, follow these troubleshooting steps: • Verify electrical power is supplied to the oven. • Verify proper electrical connections. • If the oven does not operate properly, contact Wolf Factory Certified Service. Do not attempt to repair the oven. Wolf is not responsible for service required to correct a faulty installation.
Horno de velocidad Contenido Aviso importante 3 Horno de velocidad Para garantizar que este producto se instale y opere de la forma más segura y eficiente posible, tome nota de los siguientes tipos de información resaltada en este manual: 4 Especificaciones 8 Instalación 9 Resolución de problemas Las características y especificaciones están sujetas a cambios sin previo aviso. Visite wolfappliance.com/specs para obtener la información más actualizada.
Horno de velocidad Información del producto La información importante del producto, incluidos el modelo y el número de serie de la unidad, se encuentra en la placa de datos del producto. La placa de datos se encuentra en el lado inferior izquierdo del marco de la cara frontal. La puerta del horno debe estar abierta para ver la placa de datos. Consulte la siguiente ilustración.
Especificaciones Requisitos de instalación El horno de velocidad se puede instalar en una aplicación estándar o empotrable. REQUISITOS DE INSTALACIÓN Dé el acabado a los bordes de la abertura. Pueden ser visibles cuando la puerta está abierta. Modelo de 24" (610) Modelo de 30" (762) Para instalaciones estándares, el ribete frontal se superpondrá a los largueros y guías. Consulte la tabla.
Especificaciones Requisitos eléctricos La instalación debe cumplir con todos los códigos eléctricos vigentes. Coloque el suministro eléctrico como se muestra en las ilustraciones de las páginas siguientes. El receptáculo también puede colocarse en un gabinete contiguo dentro del alcance del cable de alimentación eléctrica. Se necesita un circuito independiente que le suministre electricidad únicamente a este electrodoméstico.
Especificaciones Horno de velocidad INSTALACIÓN ESTÁNDAR 23" (584) PROFUNDIDAD DE LA ABERTURA VISTA SUPERIOR E 17 11/16" (449) ALTURA DE LA ABERTURA W ANCHO DE LA ABERTURA VISTA LATERAL VISTA FRONTAL NOTA: Los modelos de 24" (610) y 30" (762) requieren las mismas dimensiones de abertura. ANCHO DE LA ABERTURA W Modelo de 24" 221/8" (562) Modelo de 30" 221/8" (562) 6 | Atención al cliente de Wolf 800.222.
Especificaciones Horno de velocidad INSTALACIÓN EMPOTRABLE 24" (610) PROFUNDIDAD DE LA INSTALACIÓN 7/8" (22) EMPOTRABLE CORNAMUSAS TERMINADAS* VISTA SUPERIOR E 18 1/8" (460) ALTURA DE LA INSTALACIÓN EMPOTRABLE** 5/16" (8) A 1/8" (3) W ANCHO DE LA INSTALACIÓN EMPOTRABLE** VISTA LATERAL VISTA FRONTAL * Será visible y debe tener un acabado que haga juego con los gabinetes. **La dimensión especifica los márgenes mínimos.
Instalación Instalación 1 Desconecte la alimentación del tomacorriente eléctrico. 2 Mueva la unidad cerca de la abertura. Retire y recicle los materiales de embalaje. 3 El modelo de 30" (762) se entrega con dos soportes de embalaje que se encuentran a cada lado detrás de la cara frontal. Retire los dos soportes e instale los tornillos. Consulte la siguiente ilustración. 4 Conecte el cable de alimentación eléctrica en un tomacorriente con conexión a tierra.
Resolución de problemas Solución de problemas AVISO IMPORTANTE: Si el horno de velocidad no funciona correctamente, siga estos pasos para resolver los problemas: • Compruebe que el horno tiene corriente eléctrica. • Compruebe que las conexiones eléctricas estén correctas. • Si el horno no funciona correctamente, póngase en contacto con el centro de servicio autorizado de Wolf. No intente reparar el horno. Wolf no es responsable del servicio necesario para corregir una instalación defectuosa.
Four à cuisson rapide Table des matières Remarque importante 3 Four à cuisson rapide Pour s’assurer que ce produit est installé et utilisé en toute sécurité et aussi efficacement que possible, prenez note des types de renseignement mis en évidence tout au long de ce guide : 4 Spécifications 8 Installation 9 Dépannage Les caractéristiques et les spécifications peuvent être modifiées en tout temps sans préavis. Visitez wolfappliance.com/specs pour obtenir les renseignements les plus récents.
Four à cuisson rapide Renseignements sur le produit Des renseignements importants sur le produit, y compris les numéros de modèle et de série, se trouvent sur la plaque signalétique du produit. La plaque signalétique est située sur le côté gauche du cadre du panneau avant. La porte du four doit être ouverte pour voir la plaque signalétique. Reportez-vous à l’illustration ci-dessous. Si vous avez besoin de service, communiquez avec le service Wolf certifié par l’usine avec les numéros de modèle et de série.
Spécifications Exigences d’installation Le four à cuisson rapide peut être installé dans une application standard ou à affleurement. EXIGENCES D’INSTALLATION Finissez les rebords de l’ouverture. Ils peuvent être visibles lorsque la porte est ouverte. Modèle de 24 po (610) Modèle de 30 po (762) Pour les installations standards, la garniture frontale chevauchera les montants et les rails. Reportez-vous au tableau.
Spécifications Exigences électriques L’installation doit se conformer à tous les codes électriques applicables. Repérez l’alimentation électrique, comme il est montré dans les illustrations aux pages suivantes. La prise peut aussi se trouver dans une armoire adjacente à la portée du cordon d’alimentation. Un circuit séparé servant uniquement cet appareil est requis. Un disjoncteur de fuite de terre (GFCI) n’est pas recommandé et peut interrompre le fonctionnement.
Spécifications Four à cuisson rapide INSTALLATION STANDARD 23 po (584) PROFONDEUR DE L’OUVERTURE VUE DE DESSUS E 17 11/16 po (449) HAUTEUR DE L’OUVERTURE W LARGEUR DE L’OUVERTURE VUE DE PROFIL VUE DE FACE REMARQUE : Les modèles de 24 po (610 mm) et 30 po (762 mm) nécessitent les mêmes dimensions d’ouverture. LARGEUR DE L’OUVERTURE W Modèle de 24 po 221/8 po (562) Modèle de 30 po 221/8 po (562) 6 | Service à la clientèle de Wolf 800.222.
Spécifications Four à cuisson rapide INSTALLATION À AFFLEUREMENT 24 po (610) PROFONDEUR DE L’AFFLEUREMENT 7/8 po (22) TAQUETS FINIS* VUE DE DESSUS E 5/16 po (8) 1/8 po (3) 18 1/8 po (460) HAUTEUR DE L’AFFLEUREMENT** A W LARGEUR DE L’AFFLEUREMENT** VUE DE PROFIL VUE DE FACE *Seront visibles et doivent avoir une finition correspondant à l’ébénisterie. **La dimension fournit des jeux minimums.
Installation Installation 1 Coupez le courant vers la prise électrique. 2 Déplacez l’unité près de l’ouverture. Retirez et recyclez les matériaux d’emballage. 3 Le modèle de 30 po (762) est expédié avec des supports d’expédition situés de chaque côté, derrière la face frontale. Retirez les deux supports, puis réinstallez les vis. Reportez-vous à l’illustration ci-dessous. 4 Branchez le cordon d’alimentation dans la prise mise à la terre.
Dépannage Dépannage REMARQUE IMPORTANTE : Si le four à cuisson rapide ne fonctionne pas correctement, suivez les étapes de dépannage suivantes : • Vérifiez l’alimentation électrique du four. • Vérifiez les connexions électriques. • Si le four ne fonctionne pas correctement, communiquez avec le centre de service Wolf certifié par l’usine. Ne tentez pas de réparer le four. Wolf n’est pas responsable du service requis pour corriger une installation défectueuse.
WOLF APPLIANCE, INC. P.O. BOX 44848 MADISON, WI 53744 9021482 REV-B 4 / 2021 WOLFAPPLIANCE.COM 800.222.