Technical Specifications

Step 2 – Perform a Splash Test:
Once wood is dry to touch, sprinkle several handfuls of
water on a few distinct areas of the surface. If the water
spreads and begins to dry within 20 minutes, the surface
is ready to be coated. If the water beads, puddles or does
not dissipate and begin to dry within this timeframe, re-
apply surface prep product and repeat Splash Test.
Recommended Application Method
Homeowner/DIY’er:
Stain Pad – Synthetic short nap style.
Brush – Synthetic bristle.
Always work from end to end on one board at a time. When
using a pad or brush, make long, even strokes, avoid back-
and-forth movements and maintain a wet edge. Work from
dry surface into wet coating to help avoid lap marks. Cut in
with brush where pad will not reach.
Pump Style Sprayer – NOT recommended for exotic
hardwood coating.
Professional Contractor:
Airless Sprayer – Use 4-5 inch fan, .013-.015 inch, 250-500
psi, and pad or brush along grain any drips, runs, uneven
coverage or surface puddles before they dry, especially on
vertical surfaces.
Application Instructions
Before You Start – Prior to project start date, perform a
trial brush-out in several inconspicuous areas to ensure
the desired color is achieved. (Color appearance will vary
depending on wood species, age and surface porosity). Make
sure entire wood surface is dry free of dust, dirt and debris.
Cover all surrounding areas not intended to be coated.
Intermix multiple gallons of the same product in a separate
container to ensure a uniform color. Mix thoroughly before use
and stir with a lifting motion periodically during application. Do
not tint, dilute or mix this product with any other product.
Important: If the surface is in direct sunlight and hot
to the touch, liberally dampen surface with fresh water
to cool. Remove any standing water before beginning
application.
Weather Conditions – For best results, apply when outside
temperature is between 50 ° F and 90 ° F, and when no
precipitation is expected for 24 hours. Do not coat wood that is
in direct sun and hot to the touch – work earlier or later in the
when surface temperature is cooler, or dampen surface with
water to cool.
Recommended Number of Coats – APPLY ONLY ONE
(1) COAT. DO NOT OVER-APPLY. DO NOT PUDDLE.
Clean up over-spray, drips or spatters with water as soon as
possible.
CAUTION: BARE WOOD OR COATED SURFACES
CAN BECOME SLIPPERY WHEN WET. Use caution
when walking on wet surfaces.
Coverage Rate – Approximately 300-350 sq. ft./gallon for
one coat. Actual coverage will vary depending on wood age
and species, surface porosity, method of application.
Dry Time – Because temperatures and humidity fluctuate,
allow a minimum 24 hours before using deck or sitting on
outdoor furniture. Avoid dragging furniture across deck surface.
Clean Up – Clean tools and equipment immediately after use
with water. Clean up over-spray, drips or spatters on
surrounding surfaces with fresh water before they dry. If dried,
use mineral spirits or lacquer thinner.
Storage – KEEP FROM FREEZING. Keep container closed
when not in use.
Technical Data
Weight per Gallon: 8.4 +/- 0.2 lbs.
Solids by Weight: 12.98%
Solids by Volume: 11.15%
Viscosity Range: 14 – 17 seconds #2 Zahn
V.O.C. Content: Max. 2.1 lbs./gal. 250 g/l
Meets federal and all states V.O.C.
requirements.
Flash Point: None
Compatibility: Do not apply over a painted, stained or
sealed surface.
Precautions
CAUTION: May cause eye and skin irritation. Avoid eye
contact. Avoid prolonged or repeated contact with skin. Wear
appropriate eye protection and protective clothing. Wash
thoroughly after handling. Do not take internally. Avoid
breathing vapors and mists. Use only with adequate ventilation.
KEEP OUT OF THE REACH OF CHILDREN.
Limited Warranty
The Company warrants Wolman
®
E-H-T
TM
Exotic Hardwood
Treatment (Product) will perform as claimed if directions are
followed. This warranty applies to Product applied to newly
installed or pre-existing wood surfaces only if the surface has
been properly prepared and the Product has been properly
applied in accordance with directions on the Product Label.
Label directions are as complete as possible but cannot
encompass all conditions, applications and /or surfaces, all of
which are beyond manufacturer’s and seller’s control. This
warranty does not apply to use of the Product in
combination with other materials. See Product label for
warranty remedy instructions.