Use and Care Manual

ManualsBrandsWolman ManualsPaint1-gal. F&P Golden Pine Exterior Wood Stain Finish and Preservative (4-Pack)

TECHNICAL DATA

WOL-03

WOLMAN

F&P

FINISH AND PRESERVATIVE

Form: GDH-18

Rev.: 032113

].DESCRIPTION AND USES .

Wolman

F&P

Finish and Preservative is designed to

beautify and protect new or weathered wood from rot and

decay due to mold, mildew, premature graying from UV

exposure, and water damage caused by moisture

absorption. This product is suitable for use on all species

of pressure-treated lumber, Cedar, Redwood, Poplar,

Hickory, and North American hardwoods.

Wolman F&P Finish and Preservative will enhance the

color of wood and protect newly installed or existing

decks, fences, siding or roofing shakes and shingles,

clapboard, exterior doors, window frames and trim, boat

docks, boardwalks, arbors and trellises, storage sheds

and other outdoor equipment and furniture.

Important! –Do not use on wood which will come in

contact with food. Keep container closed when not in use.

Wear goggles, rubber gloves and protective clothing when

applying or handling treated lumber. Use only in a

ventilated area. Keep contents and freshly treated articles

away from food and living plants.

.PRODUCTS .

1-Gallon 5-Gallon Description

14426 14425 Golden Pine

14396 14395 Natural

14416 14415 Cedar

14406 14405 Redwood

.PRODUCT APPLICATION .

SURFACE PREPARATION

Conduct a splash test on bare wood to confirm water

absorption before applying this product. Note: Chlorine

bleach cleaners alone are not recommended. These

products degrade the wood structure, interfering with

penetration and adhesion of protective coatings. To

conduct a Splash Test, sprinkle several handfuls of water

on a few distinct areas of the bare wood surface. If the

water absorbs rapidly, the surface is ready to be coated. If

the water beads, puddles or is not absorbed, an internal or

external barrier exists, which must be eliminated before

application of the preservative finish. Prepare the surface

with Wolman

DeckBrite

™

(Powder Concentrate), Deck &

Fence Brightener (Liquid Concentrate) or DeckStrip

products and repeat the splash test to confirm water

absorption before applying this product..

PRODUCT APPLICATION (cont.) .

UNCOATED, NEW WOOD: It is important to open wood

pores and remove any surface barrier which would

prevent the proper penetration or adhesion of a new

coating. If the wood is pressure-treated lumber, excess

surface wax or excessive internal moisture content may be

present. If new wood is Cedar or Redwood is used, “mill

glaze” on the surface is a common condition. Use either

Wolman DeckBrite powder concentrate or Deck & Fence

Brightener liquid concentrate according to label directions,

then conduct a Splash Test. If absorption is not improved,

allow the wood to dry a minimum of 30 days in temperate

weather (70°F and 50% RH), longer in cooler or more

humid conditions. Test for absorption again before

applying this product.

UNCOATED, WEATHERED WOOD: Before coating,

weathered wood must be thoroughly cleaned to remove

the grayed, UV damaged wood surface, ground-in dirt,

mildew and algae stains, and other surface contaminants.

Use either Wolman DeckBrite powder concentrate or Deck

& Fence Brightener liquid concentrate according to label

directions to prepare the surface.

PREVIOUSLY COATED, WEATHERED WOOD: Previous

coatings should be removed before application of this

product. If pigmented oil or latex coating exists, use

Wolman DeckStrip Stain & Finish Remover according to

the label directions to prepare the surface. Acrylic coatings

may require a paint stripper. If coated with a clear sealer

or the remaining finish contains little to no pigment, use

Wolman DeckBrite powder concentrate or Deck & Fence

Brightener liquid concentrate, followed by pressure

washing to restore the surface and remove and residual

coating or water repellent.

Before applying this oil-based product, wait at least 24

hours after cleaning, stripping or power-washing to

allow the water-soaked wood to dry out thoroughly.

Oil-based finishes will not properly penetrate wood

that is water soaked.

APPLICATION

BEFORE YOU START: Prior to project start date, perform

a trial brush-out in several inconspicuous areas to ensure

the desired color is achieved. Color appearance will vary

depending on wood species, age and surface porosity.

Replace rotted, extremely weathered or warped boards.

This product will not repair existing wood damage such as

cracking, checking, splintering or splitting. Make sure

entire wood surface is dry and free of dust, dirt and debris.

Cover all surrounding areas not intended to be coated.

Intermix or box multiple gallons of the same product color

in a separate container to ensure a uniform color. Do not

tint, dilute or mix this product with any other product. Mix

product thoroughly before use and stir occasionally during

application.

Summary of content (3 pages)

PAGE 1
TECHNICAL DATA WOL-03 WOLMAN® F&P® FINISH AND PRESERVATIVE ].DESCRIPTION AND USES ® PRODUCT APPLICATION (cont.) . UNCOATED, NEW WOOD: It is important to open wood pores and remove any surface barrier which would prevent the proper penetration or adhesion of a new coating. If the wood is pressure-treated lumber, excess surface wax or excessive internal moisture content may be present. If new wood is Cedar or Redwood is used, “mill glaze” on the surface is a common condition.
PAGE 2
TECHNICAL DATA WOLMAN® F&P® FINISH AND PRESERVATIVE PRODUCT APPLICATION (cont.) . Apply when outside temperatures are between 50-90°F (10-38°C) and when no precipitation is expected for 24 hours. Do not apply to wood that is hot to touch or in direct sunlight to prevent premature evaporation of solvent. Apply with a natural or synthetic bristle brush, paint pad, pump sprayer, or airless sprayer.
PAGE 3
TECHNICAL DATA WOLMAN® F&P® FINISH AND PRESERVATIVE ,PHYSICAL PROPERTIES PHYS IC FINISH & PRESERVATIVE Resin Type Alkyd Pigment Type Inorganic Solvents Weight Solids Mineral Spirits Per Gallon 9.4 lbs. Per Liter 1.13 kg By Weight 48-50% By Volume 46-48% Volatile Organic Compounds <280 g/l (15.0 lbs./gal.) Recommended Dry Film Thickness (DFT) Per Coat 3.0-4.0 mils Wet Film to Achieve DFT (unthinned material) 6.0-8.0 mils Theoretical Coverage at 1 mil DFT (25µ) 770 sq.ft./gal.