Technical Specifications

ManualsBrandsWolman ManualsExterior Paint & StainDuraStain® One Coat Chestnut Brown Solid Color Stain - 1 gal.

TECHNICAL DATA WOL-17

DURASTAIN

ONE COAT SOLID COLOR STAIN

1 Form: GDH-698

Rev.: 052418

.DESCRIPTION AND USES

Wolman

™

DuraStain

One Coat Solid Color Stain is a one coat,

water-based exterior wood stain designed to provide excellent

color retention, adhesion and protection against UV graying,

water damage and mildew. DuraStain decorates wood with a

deeply pigmented opaque color in a matte finish that enhances

wood texture and provides solid hide coverage over new or

previously coated, weathered wood.

The NeverWet

hydrophobic technology properties and superior

water repellency helps maximize resistance to wood cracking,

checking, splitting and warping. DuraStain One coat Solid Color

Stain is suitable for use on all types of pressure treated lumber,

Cedar, Redwood, Poplar, Hickory and other North American

hardwoods. It may also be used on wood composite lumber,

hardboard siding, plywood, T1-11 and MDO panel siding. It is

suitable for use on weathered wood, where hiding the signs of

aging is desired. Follow specific manufacturer’s

recommendation before applying to any composite decking.

Use DuraStain One Coat Solid Stain to beautify and protect

decks, porches, fences, shake, shingle and clapboard siding,

boat decks, boardwalks, outdoor furniture, gazebos, arbors and

trellises, storage sheds and more.

FOR CONCRETE: For use on broom swept or porous concrete

surfaces. Do not use on smooth or floated concrete. Do not use

on driveways, garages or other areas with vehicular traffic.

TINT BASE MUST BE TINTED BEFORE USE

Wolman DuraStain One Coat can be applied using a ⅜” nap

roller, a short nap stain pad or a synthetic paint brush. Do

not use a pump style sprayer or conventional sprayer.

..PRODUCTS .

SKU Description

288073 Neutral Base (1-Gallon)

288076 Chestnut Brown (1-Gallon)

288080 Natural Cedar (1-Gallon)

288092 Natural Redwood (1-Gallon)

288094 White Base (1-Gallon)

288095 Neutral Base (5-Gallon)

288103 Neutral Base (5-Gallon)

..PERFORMANCE CHARACTERISTICS .

 One coat application

 Ready for use in 48 hours

 Mildew resistant coating

 Superior water repellency

 NeverWet properties

..PRODUCT APPLICATION .

SURFACE PREPARATION

REGARDLESS OF AGE OR SURFACE CONDITION,

FAILURE TO FOLLOW ONE OF THESE PREPARATION

METHODS WILL RESULT IN POOR ADHESION AND

POSSIBLE COATINGS FAILURE. NEW AND SEALED WOOD

DECKS NEED TO WEATHER AT LEAST 6 MONTHS

BEFORE APPLICATION.

Prepare the surface with Wolman DeckStrip

or DeckStrip

ASR, then use Wolman DeckBrite

™

or Deck & Fence

Brightener based on wood condition described below.

After preparation, conduct a Splash Test on bare wood

(described below) to confirm water absorption before applying

this product.

PREVIOUSLY COATED, WEATHERED WOOD

For best results, previous coatings such as paints, solid color and

semi-transparent stains, transparent stains, toners or clear

sealers in a weathered state, should be stripped to create a bare,

sound surface for maximum coating adhesion and durability. To

remove oil, alkyd or latex, water base stains, use Wolman

DeckStrip Stain & Finish Remover. For 100% acrylic solid or

semi-solid stains, use Wolman DeckStrip ASR Acrylic Stain

Remover.

Thoroughly clean with Wolman DeckBrite or Deck & Fence

Brightener to remove chalky paint residue, embedded dirt,

mildew and other contaminants, residual coating material and

water repellents. According to label guidelines, select the

appropriate cleaning product for your wood type, use according

to directions and rinse with a power washer for best results.

When dry, scrape off and sand any remaining loose flaking or

peeling coating using 50 or 60 grit sandpaper. After wood is dry,

conduct a splash test (described below).

UNCOATED, WEATHERED WOOD

Before staining, bare, weathered wood must be thoroughly

cleaned to remove ground-in dirt, mildew, mold and algae stains,

gray, UV damaged wood fibers any other surface contaminants.

According to label guidelines, select the appropriate product for

your particular wood type, either Wolman DeckBrite or Deck &

Fence Brightener; then follow usage directions on the label, rinse

and let dry. After wood is rinsed and dry, conduct a Splash Test

(described below).

UNCOATED, NEW WOOD

New wood decks need to weather at least 6 months before

application. After wood has weathered 6 months, it is important

to open wood pores and remove any surface barrier which would

prevent the proper penetration or adhesion of a new coating. If

pressure-treated lumber, excess surface wax or excessive

internal moisture content may be present. If new wood is Cedar

or Redwood, “mill glaze” on the surface is a common condition.

Summary of content (3 pages)

PAGE 1
TECHNICAL DATA WOL-17 DURASTAIN® ONE COAT SOLID COLOR STAIN .DESCRIPTION AND USES ™ ..PRODUCT APPLICATION . ® Wolman DuraStain One Coat Solid Color Stain is a one coat, water-based exterior wood stain designed to provide excellent color retention, adhesion and protection against UV graying, water damage and mildew. DuraStain decorates wood with a deeply pigmented opaque color in a matte finish that enhances wood texture and provides solid hide coverage over new or previously coated, weathered wood.
PAGE 2
TECHNICAL DATA WOL-17 DURASTAIN ONE COAT SOLID COLOR STAIN ..PRODUCT APPLICATION (cont.) ..PRODUCT APPLICATION (cont.) . . SURFACE PREPARATION (cont). APPLICATION (cont.) Eliminate these barriers by using either Wolman DeckBrite or Deck & Fence Brightener. According to label guidelines, select the appropriate product for your particular wood type, follow usage directions on label, rinse and let dry. After wood is rinsed and dry, conduct a Splash Test (described below).
PAGE 3
TECHNICAL DATA WOL-17 DURASTAIN ONE COAT SOLID COLOR STAIN PHYSICAL PROPERTIES . ONE COAT SOLID COLOR STAIN Resin Type Acrylic Polyurethane Pigment Type Titanium Dioxide, Iron Oxides and Mica Solvents Weight Solids Water Per Gallon 9.6-10.6 lbs. Per Liter 1.15-1.27 kg By Weight 43.6-49.2% By Volume 34.6-34.9% Volatile Organic Compounds <100 g/l (0.83 lbs./gal.) Recommended Dry Film Thickness (DFT) Per Coat 2.0 mils (50µ) Wet Film to Achieve DFT 6.0 mils (150µ) 560 sq.ft./gal. 2 (13.