Technical Specifications

ManualsBrandsWolman ManualsExterior Latex PaintApple Red Outdoor Furniture Paint- 1 qt.

TECHNICAL DATA WOL-22

DURASTAIN

OUTDOOR FURNITURE COATING

Form: GDH-1057

Rev.: 052418

DESCRIPTION AND USES .

Wolman

™

DuraStain

Outdoor Furniture Coating is a water-

based acrylic wood coating designed to refresh exterior wood

furniture, picnic tables, playsets and more. DuraStain Outdoor

Furniture is 4X thicker for enhanced durability and provides

excellent weather resistance in the harshest weather conditions.

It decorates wood furniture with deeply pigmented, bright color

that provides solid hide. Use on all species of pine, fir, Hem-Fir,

cypress, cedar, redwood, poplar, hickory and other North

American hardwoods.

Not for use on composite decking, concrete, fiberglass, tile

or metal surfaces. These surfaces will not allow for proper

adhesion. Do not use on driveways, garages or other

areas with vehicular traffic.

Wolman DuraStain Outdoor Furniture tint base must be

tinted at the store of purchase. DO NOT APPLY IF

PRODUCT HAS NOT BEEN TINTED. Wolman DuraStain

Outdoor Furniture can be applied using a ⅜” or ½” nap

roller or a synthetic paint brush.

. FEATURES .



4X thicker for enhanced durability



Excellent weather resistance



Waterproofing protection



Extends life of wood furniture

.PRODUCTS .

SKU Description

305230 Outdoor Furniture – 1-Gallon

305323 Outdoor Furniture – 1-Quart

COMPANION PRODUCTS ...

SKU Description

16116 Wolman Deck & Fence Brightener

14446 Wolman DeckStrip

PRODUCT APPLICATION .

The preparation process outlined below should be followed to

achieve optimum performance of this product. Long term

adhesion and durability can be impaired by an unsound or poorly

prepared surface.

REGARDLESS OF AGE OR SURFACE CONDITION,

FAILURE TO FOLLOW ONE OF THESE PREPARATION

METHODS MAY RESULT IN POOR ADHESION AND

POSSIBLE COATINGS FAILURE. NEW AND SEALED WOOD

NEEDS TO WEATHER AT LEAST SIX MONTHS BEFORE

APPLICATION.

READ ALL INSTRUCTIONS BEFORE BEGINNING

PROJECT.

PRODUCT APPLICATION (cont) .

SURFACE PREPARATION

Prepare the surface with Wolman DeckStrip or Wolman Deck &

Fence Brightener based on your wood condition. After

preparation, conduct a splash test by sprinkling water on the

surface. If the water absorbs rapidly into the wood, the surface is

ready to coat. If the water beads, puddles or is not absorbed, an

internal or external barrier exists and must be eliminated before

staining can begin.

PREVIOUSLY COATED, WEATHERED WOOD

For best results, previous coatings such as paints, solid color and

semi-transparent stains in a weathered state should be stripped

from the surface to create a bare, sound surface for maximum

coating adhesion and durability. To remove oil, alkyd or latex or

water-based stains, use Wolman DeckStrip Stain & Finish

Remover. For 100% acrylic solid or semi-solid stains, use

DeckStrip ASR Acrylic Stain Remover.

For previous coatings in sound condition, and for weathered

transparent finishes, toners and clear sealers, thoroughly clean

with Wolman DeckBrite powder concentrate or Deck & fence

Brightener liquid concentrate to remove chalky paint residue,

embedded dirt, mildew and other contaminates, residual coating

material and water repellents. Select the appropriate cleaning

product for your wood type, use according to directions and rinse

with a power washer for best results. When dry, scrape off and

sand any remaining loose, flaking or peeling coating using 50 or

60 grit sandpaper.

UNCOATED, WEATERED WOOD

Before staining, bare weathered wood must be thoroughly

cleaned to remove ground-in dirt, mildew, mold and algae stains,

gray UV damaged wood fibers and any surface contaminates.

Select the appropriate product for your wood type, either

Wolman DeckBrite powder concentrate or Deck & Fence

Brightener liquid concentrate. Follow usage directions on the

label, let dry and then conduct a splash test.

UNCOATED, NEW WOOD

It is important to open wood pores and remove any surface

barrier which would prevent proper penetration or adhesion of a

new coating. If pressure treated lumber is used, excess surface

wax or excessive internal moisture content may be present. If the

wood is new cedar or redwood, “mill glaze” on the surface is

common. Eliminate these barriers by using either Wolman

DeckBrite powder concentrate or Deck & Fence Brightener liquid

concentrate. Select the appropriate product for your particular

wood type, then follow usage directions on the label, let dry, and

then conduct a splash test.

Summary of content (3 pages)

PAGE 1
TECHNICAL DATA WOL-22 DURASTAIN® OUTDOOR FURNITURE COATING DESCRIPTION AND USES ™ PRODUCT APPLICATION (cont) . ® SURFACE PREPARATION Wolman DuraStain Outdoor Furniture Coating is a waterbased acrylic wood coating designed to refresh exterior wood furniture, picnic tables, playsets and more. DuraStain Outdoor Furniture is 4X thicker for enhanced durability and provides excellent weather resistance in the harshest weather conditions.
PAGE 2
TECHNICAL DATA DURASTAIN® OUTDOOR FURNITURE COATING PRODUCT APPLICATION (cont) . PRODUCT APPLICATION (cont) . SURFACE PREPARATION (cont.) APPLICATION Houses painted before 1978 may contain lead. TWO LIBERAL COATS OF WOLMAN DURASTAIN OUTDOOR FURNITURE ARE REQUIRED. WARNING! If you scrape, sand or remove old paint from any surface, you may release lead paint dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE; ESPECIALLY IN CHILDREN.
PAGE 3
TECHNICAL DATA DURASTAIN® OUTDOOR FURNITURE COATING PHYSICAL PROPERTIES . OUTDOOR FURNITURE Resin Type Water-based Acrylic Pigment Type A blend of Inorganic and Organic Pigments Solvents Glycol Ethers, Water Per Gallon 11.6-11.9 lbs Per Liter 1.39-1.43 kg By Weight 66.0-69.0% By Volume 53.4-54.4% Weight Solids Volatile Organic Compounds <50 g/l (0.42 lbs./gal.) Recommended Dry Film Thickness (DFT) Per Coat Practical Coverage at Recommended DFT 4 mils Approximately 80 sq.ft./gal.