Wolverine Data PASS-200 Portable Scanner User Manual V1.
Table of Contents 1. Before Using the PASS-200 Battery Powered Portable Scanner - 2 Having difficulty using this product? ------------------------------------- 3 2. FCC Notice --------------------------------------------------------------------- 4 3. Packaging Contents --------------------------------------------------------- 4 4. Component Guide ------------------------------------------------------------ 5 5. LCD Screen / Status --------------------------------------------------------- 6 6.
Thank you for purchasing Wolverine PASS-200 Portable Scanner. This handheld battery operated scanner gives you the freedom to scan documents, magazines, photos, newspapers, or books on the fly. PASS-200 Scanner has a unique double roller mechanism and produces easy and perfect scans every time. It saves all your scans directly to a Micro-SD or SDHC memory card; no computer or software is required. Please take a moment to read through this manual. Its contents may help you to get the best use of the scanner.
Do not move or disconnect the device from the computer while the device is reading/writing data. This may cause damage to the data and/or the device. Under no circumstances should user try to repair the device. Doing so may cause electrical shock and void the warranty. Warranty will be void if the device is mishandled. Please take care in handling the PASS-200 Portable Scanner. Wolverine Data is not responsible for consequential damages, including loss of data. Always back up all data.
E-mail or write to our technical support staff at support@wolverinedata.com or to our address: 9939 Muirlands Blvd. Irvine, CA 92618. 2. FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
4. Component Guide Item Name Functions 1 Battery door For 2xAA alkaline batteries 2 POWER/SCAN Power on/off: Press and hold this button for 2 - 5 seconds to turn power on or off. In power-on mode, press this button start scanning; press this button again to stop scanning. 3 ERR LED indicator Over speed: Red LED on Press SCAN button once to clear error 4 SCAN LED indicator Ready for scan: Green LED on 5 LCD screen Scan status display 6 C/BW button Select Color or Mono scan.
5. LCD Screen / Status Item 1 Function SD card indicator Description Files will be stored in MicroSD or SDHC memory card Storage: Micro-SD or SDHC Card, max.
6. Getting Started 6.1 Install battery 1) Slide battery door outward. Please see the picture. Insert 2 x AA batteries (not supplied) into the battery compartment according to the polarities shown in the compartment. 6.2 Power on/off the scanner 2) Press and hold Power/Scan button for 2~5 seconds to turn on/off the scanner. 6.3 Insert and format a MicroSD or SDHC memory card You need to use a MicroSD or SDHC card to record and store the scanned files. The scanner supports the capacity up to 32GB.
6.4 Set system date and time 1) 2) 3) Power on the scanner. Use the tip of a paper clip to press “TIME SET” hole. The item # has 1 to 5 in sequence, represents Year(1), Month(2), Day(3), Hour(4), and Minute(5) accordingly. Press C/BW (increasing) or DPI button (decreasing) to change the settings. After each item is set, press Scan button to confirm the change. When finished all 5 settings, use paper clip to press “TIME SET” hole again to complete the process. 6.
5) 6) 7) Don’t move the scanner and wait for the red LED to go off, and then slide the scanner across on the white area back and forth slowly and smoothly until the green LED goes off. The white color balance calibration is completed. Repeat the calibration process as needed. 6.6 Set color mode and resolution The default settings are in COLOR mode and LOW resolution. Press DPI button to select resolution in HIGH or LOW. And press C/BW button to select color in COLOR or MONO mode. 6.
6.8 LED light indication Both Green and Red LED off ---- Ready to scan. Press SCAN button to start a scan. Green LED on ---- Scanning in process Red LED on ---- Scanned too fast or having distortion. Press SCAN button once to clear error. 7. Connect to computer You may connect the scanner to your computer to upload files in the MicroSD or SDHC memory card. 1) Use the included USB cable to connect scanner to USB port on your computer. 2) Turn on the scanner.
8. Specifications Image sensor A4 Color Contact Image Sensor Number of sensor 5138 dots ( 1 -5104 dots available) Resolution Low resolution: 300x300 dpi (default) High resolution: 600x500 dpi Maximum scanning speed for Letter size document Color High resolution Mono High resolution Color Low resolution Mono Low resolution 13 seconds 6 seconds 3 seconds 2 seconds Capacity ( Based on 1GB card and Letter size images) 600dpi color 600dpi mono 300dpi color 300dpi mono 220 Photos (Min.
10. Troubleshooting Tips 1. Cannot turn on the scanner. 2. Battery power may be low or batteries were not installed properly. Check the polarities of the batteries or replace with new batteries. Cannot save scanned files. 3. MicroSD or SDHC card might not be formatted properly; MicroSD or SDHC card might be corrupted; the memory card might not be inserted properly, or the memory card might be full. Computer doesn’t recognize the scanner. 4. Check USB cable connection or restart the computer.
Damage due to shipping the product to you is covered under this limited warranty. Otherwise, this limited warranty does not cover damage due to external causes, including accident, abuse, misuse, problems with electrical power, servicing not authorized by Wolverine Data, usage not in accordance with product instructions, failure to perform required preventive maintenance, and problems caused by use of parts and components not supplied by Wolverine Data.
continental United States, where applicable. Shipments to other locations will be made freight collect. To obtain service, you must include: (a) a copy of your receipt or other comparable proof of purchase; (b) a written description of the problem; (c) your address and telephone number; (d) Write the RMA number on the outside shipping packaging. NOTE: Wolverine Data uses new and reconditioned parts made by various manufacturers in performing limited warranty repairs and building replacement products.
other peripheral equipment on PASS-200 scanner are excluded from coverage. Unauthorized Service or Modification. Defects or damages resulting from service, testing, adjustment, instillation, maintenance, alteration, or modification in any way by someone other than Wolverine Data are excluded from coverage. Altered Products.
Thank you for choosing Wolverine! Having difficulty using PASS-200 Scanner? Please try the following options: Call us at 949-458-9888 M-F 9:00-5:00 Pacific Time. Visit www.wolverinedata.com/support to find the latest documentation and other help tips. E-mail or write to our technical support staff at support@wolverinedata.com. Quick Start Guide 1. 2. 3. Slide battery door outward. Install 2 x AA batteries (not supplied). Power on the scanner - Press and hold POWER/SCAN button for 2~5 seconds. 4.