WIOS-5.8 SPEAKER SYSTEM User Manual Version 1.0 5.
INTRODUCTION The Wolverine WIOS-5.8 (5.8 GHz Digital All Wireless Outdoor/Indoor Dual Speaker System) allows you to enjoy the rich 5.8 GHz digital Hi-Fi and cinema-surround sound wirelessly throughout your house, in your yard, on the patio, by the pool, and on your boat or RV. With the optional Wolverine Colossal portable power pack, you can bring all the Wolverine fun to the park, to the camp, or to the job-site, where no electrical outlet is available.
SAFETY INFORMATION AND INSTRUCTIONS Please take the time to read and follow safety instructions in this Manual carefully. It will help you to use your new Wolverine® product properly and enjoy its features more. . . . . . . .. . . . . To reduce the risk of fire or electric shock, do not expose this product to rain, moisture, water dripping or splashing. Use care not to spill liquids into any part of the device.
PACKAGE CONTENTS 1. Speaker receivers 2. Transmitter 3. Remote control 4. Power adapters: DC 5V for transmitter DC 12V for speakers, 2 pieces 5. Audio cables: 3.5 mm to 3.5 mm stereo 3.5 mm to RCA (red and white) stereo OPTIONAL ACCESSORIES All additional speakers and optional accessories are available at www.wolverinedata.com. . . . 5 Additional speaker receivers Each WIOS-5.8 transmitter can hold up to 4 paired speaker receivers.
. COMPONENTS GUIDE Speaker Power LED SYNC (Synchronizing) LED Handle Pairing button Vol - button Power ON/OFF button Vol + button Light button Illuminated LED Remote control receiver Bottom cover Inside bottom cover Audio Channel Switch L S/M R 6-Battery Compartment L- left channel S/M- Surround and Mono R- right channel 3.5 mm DC Jack . Transmitter rear view Power connector 3.5 mm DC jack DC IN 5V ON/OFF AUDIO LINE-IN Power switch PAIRING Pairing button 3.
WIOS-5.8 OPERATIONAL PROCEDURES 1. Prepare Transmitter You can connect the transmitter to audio devices such as smart phones, tablet PC, MP3 players, or many others using Bluetooth connection or the included 3.5mm audio cable. . . . . . A. Connect transmitter with audio devices Plug the included AC/DC power adapter to an electrical wall AC outlet. Insert the AC/DC power connector into the DC female-jack located on the back of the transmitter.
2. Prepare Speaker receiver . A. Audio receiving Plug the supplied Power Adapter to an electrical wall outlet, insert the connector to the DC jack, or install 6 "AA" size quality ALKALINE batteries (not included) into the battery compartment with correct polarity, at the bottom of the speaker. Press and hold the POWER ON/OFF button to turn on the speaker. The Power LED will be on.
3. Pairing All new WIOS-5.8 Speaker System was pre-paired at manufacturing facility, pairing process is not needed. In any case if user wants to pair the system, please follow the steps below. Each transmitter can connect with more than one speaker (up to 8 speakers). You can pair additional speakers to the transmitter by following the steps: . . . . . . Connect power adapters to both transmitter and speakers and power them on.
Trouble shooting . .. . .. 1. No sound . Ensure the power adapter is fully inserted into the wall outlet, and the power connection is turn on. Ensure the speakers are ON. Speaker's battery capacity might be too low. Replace new batteries or use power adapter to the speaker instead. Ensure the audio cable or Bluetooth connection to the transmitter is well connected. Ensure the connected audio or video equipment is playing.
TECHNICAL SPECIFICATION Carrier Frequency : 5.8GHz Digital , CSR Bluetooth 4.
However, this is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna on your radio or TV. Increase the separation between the WIOS-5.8 and your radio/TV. Connect the WIOS-5.
If limited warranty service is required, Wolverine Data will issue a RMA (Return Material Authorization) Number. You must ship the products back to Wolverine Data in their original or equivalent packaging, prepay shipping charges, and insure the shipment or accept the risk of loss or damage during shipment. Wolverine Data will ship the repaired or replacement products to you freight prepaid if you use an address in the continental United States, where applicable.
. Altered Products Product or accessories with (a) serial numbers or date tags that have been removed, altered or obliterated; (b) broken seals or that show evidence of tampering; (c) mismatched board serial numbers; or (d) nonconforming or non-Wolverine Data parts or accessories, are excluded from coverage.
TABLE OF CONTENTS Introduction .. 3 Features .. 3 Safety information and instructions .. 4 Package contents .. 5 Optional accessories .. 5 Components guide .. 6 WIOS-5.8 operational procedures .. 7 1. Prepare transmitter .. 7 A. Connect with audio devices .. 7 B. Connect with bluetooth devices .. 7 2. Prepare speaker receiver .. 8 A. Audio receiving .. 8 B. Audio channel selection .. 8 C. Standby/Power off .. 8 D. Ambiance light .. 8 E. Carry handle .. 8 3. Pairing .. 9 4. Remote control ..