USER’S GUIDE V: 682-01 DS-843 Bluetooth Speaker System for iPod + iPhone For the most up-to-date version of this User’s Guide, go to www.iLiveElectronics.com ISPB592-682-01-IB-0802.
Warnings and Precautions • CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. • WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. • AVERTISSEMENT: Pour réduire le risque d’incendie ou de choc électrique, ne pas exposer cet appareil sous la pluie et l’humidité. • CAUTION: Use of any controls or adjustments or performance of procedures other than those herein specified may result in hazardous radiation exposure.
Important Safety Instructions 1. Read these Instructions. 2. Keep these Instructions. 3. Heed all Warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
Bluetoooth Speaker System for iPod + iPhone Features Included • • • • • • • • • • • • • • Made for iPod and iPhone Plays and charges docked iPod and iPhone Supports profile A2DP (Advanced Audio Distribution Profile) Wireless range: 33 feet Rotating dock for iPod and iPhone iPod and iPhone authentication IC Composite video output 3.
Table of Contents Bluetoooth Speaker System for iPod + iPhone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Features Included Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction Status Indicator Pairing indicator Dock for iPod + iPhone Power/Source Press to switch between iPod and iPhone, Line In and Bluetooth mode. Press and hold to turn the power off . Talk/End/Play/Pause Press to activate the speakerphone function and accept or end calls. Press to play or pause a docked iPod/iPhone or a connected Bluetooth device. TALK/END POWER/SOURCE VOLUME Volume Press to adjust the volume. Composite Video Output Pair Press to begin pairing a Bluetooth device. PAIR 3.
Mute Press to mute the volume of the speaker. Power Press to turn the speaker off or on. POWER Menu Press to move through the menus on a docked iPod or iPhone. MUTE MENU Arrows (▲▼) Press to navigate menus on a docked iPod or iPhone. ENTER Enter Press to select menu items on a docked iPod or iPhone. VOL VIDEO Video Press to switch to Video out mode and view video on a connected television. SOURCE REPEAT Repeat Press to cycle through repeat options on a docked iPod or iPhone.
Setup Power DC power input: requires an AC/DC power adapter (included) PAIR DC IN LINE IN VIDEO OUT Remote Remote control: requires a CR2025 battery (pre-installed) IU CR M B 2 AT 3V 025 TE RY CR2025 LIT H OPEN PUSH Status Indicator iPod/iPhone Mode Green light Bluetooth Mode Blue light Line In Mode White light 8 ISPB592-682-01-IB-0802.
iPod and iPhone Docking an iPod or iPhone 1. Use the included spacers as needed to fit your iPod or iPhone into the dock. 2. Connect the iPod or iPhone to the connector inside the Dock for iPod and iPhone. 3. When the speaker is plugged in, using AC power, the docked iPod or iPhone will charge. 2.8 MM A B 1.2 MM Rotating Dock The dock will rotate 90˚ to the right or left. Do not attempt to rotate the dock further than 90˚ to either side to avoid damaging the speaker.
3.5mm Audio Input & Composite Video Output Using the 3.5mm Audio Input Using the Composite Video Output Requires a 3.5mm audio cable (included) Requires an RCA composite video cable (not included) 1. 2. 3. Connect a 3.5mm audio cable to the 3.5MM Audio Input on the speaker and an audio output on an MP3 player or other audio source. Press the Source/Power button to switch to Line In mode. 1.
Bluetooth Pairing a Bluetooth Device Playing Audio Wirelessly 1. Power on the unit by pressing the Power button. 1. Follow the instructions for Pairing a Bluetooth Device. 2. Press the Source/Power button to switch to Bluetooth mode. 2. 3. Press the Pair button. Use the native controls on the connected Bluetooth Device to select a track. 4. The Pairing Indicator will flash blue quickly. 3.
Company Information International Support Green Initiative To download this User’s Guide in English, Spanish, or French, or to get answers to frequently asked questions, visit the support section at www.iLiveElectronics. com. Para descargar este Manual del Usuario en inglés, español y francés, o para obtener respuestas a preguntas frecuentes, visite la sección de apoyo en www.iLiveElectronics. com.
