Installation and Operation Manual BISTRO HOME 3030 WS-BH-3030-RFG Bistro Home Stone Hearth Cooking Appliance Gas-Fired Residential Models Jet Style Burner BISTRO HOME 4343 WS-BH-4343-RFG WS-BH-4343-RFG-W BISTRO 4355 WS-BH-4355-RFG WS-BH-4355-RFG-W BISTRO HOME 4836 WS-BH-4836-RFG enhance your food, home & lifestyle with a Wood Stone Home Oven An ongoing program of product improvement may require us to change specifications without notice. Wood Stone Corporation 1801 W. Bakerview Rd.
Table of Contents Bistro Home Oven Installation and Operation Manual Cautions and Warnings . . . . . . . . . . . . . . . . . . . . . . . . 3 Bistro Home 3030 Specs. . . . . . . . . . . . . . . . . . . . . . . . 5 Bistro Home 4343 Specs. . . . . . . . . . . . . . . . . . . . . . . . 6 Bistro Home 4355 Specs. . . . . . . . . . . . . . . . . . . . . . . . 7 Bistro Home 4836 Specs. . . . . . . . . . . . . . . . . . . . . . . . 8 Installation Clearances. . . . . . . . . . . . . . . . . . . . . . . . .
Cautions and Warnings Bistro Home Oven Installation and Operation Manual INSTALLATION AND OPERATION MANUAL FOR THE WOOD STONE HOME BISTRO STONE HEARTH COOKING APPLIANCE • • • • • • WS-BH-3030-RFG-(NG OR LP) WS-BH-4343-RFG-(NG OR LP) WS-BH-4343-RFG-W-(NG OR LP) WS-BH-4355-RFG-(NG OR LP) WS-BH-4355-RFG-W-(NG OR LP) WS-BH-4836-RFG-(NG OR LP) WOOD STONE HOME INTERNAL TRANSITION MODELS ADDITIONAL COPIES AVAILABLE AT WOODSTONEHOME.COM PLEASE READ THIS ENTIRE MANUAL BEFORE YOU INSTALL THE APPLIANCE.
Cautions and Warnings Bistro Home Oven Installation and Operation Manual WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electrical switch. • Do not use any phone in your building. • Immediately call your gas supplier from a neighbor’s phone. • Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department.
Bistro Home 3030 Specs Bistro Home Oven Installation and Operation Manual plan view 29 1/4" 740mm 29 1/4" 11 1/4"740mm 280mm 11 1/4" 280mm O 8" 200mm OD O 8" 200mm OD 6 1/4" 160mm 6 1/4" 160mm rear view 29 1/4" 29 1/4" 740mm 740mm 11 1/4" 4" 11 1/4" 280mm 100mm 280mm 4" 100mm a 4" 4" 100mm 100mm 20" 20" 510mm 20" a 20" 510mm 510mm 510mm 29 1/4" 29 1/4" 740mm 29 1/4" 29 1/4" 740mm 740mm 740mm 36 3/4" 36 3/4" 930mm 36 3/4" 36 3/4" 930mm 930mm 930mm O 8" 200mm OD O 8" 200mm OD G G G G 6 1/4" 6160mm
Bistro Home 4343 Specs Bistro Home Oven Installation and Operation Manual 42 1/4" 1070mm 42 1/4" view plan 1070mm 18 1/4" 460mm 18 1/4" 460mm O 10" 10" O 250mm 250mm 7 1/2" 190mm 7 1/2" 190mm O 10" 250mm G O710" 1/2" 250mm G flue collar b mantle c flame height control knob d timer e control panel 18 1/4" 460mm 42 1/4" 9 1/4" 1070mm 230mm 9 1/4" 18 1/4" 230mm 460mm rear view 9 1/4" 230mm 9 1/4" 230mm a 33 1/2" 850mm 33 1/2" 850mm 33 1/2" 850mm 50" 1270mm 50"a 1270mm G 190mm 7 1/2" 190m
Bistro Home 4355 Specs Bistro Home Oven Installation and Operation Manual plan view rear view 42 1/4" 1070mm 42 1/4" 1070mm 18 1/4" 18 1/4" 460mm 42 1/4" 460mm 42 1/4" 1070mm 1070mm 9 1/2"18 1/4" 18 1/4" 240mm 460mm 460mm 9 1/2" 240mm 9 1/2" 240mm 45 1/2" 1150mm 45 1/2" 1150mm O 10" 250mm OD O 10" 250mm OD 7 1/2" 190mm 7 1/2" 190mm a flue collar b mantle c flame height control knob d timer e control panel 45 1/2" a 1150mm 54 1/4" 1380mm O 10" 250mm OD O 10" 250mm OD 7 1/2" 190mm 1/4" G
Bistro Home 4836 Specs Bistro Home Oven Installation and Operation Manual plan view rear view 47 3/4" 1210mm 20 1/4" 520mm 47 3/4" 1210mm 13 3/4" 20 1/4" 350mm 47 3/4" 47 3/4" 520mm 1210mm 1210mm 20 1/4" 20 13 1/4"3/4" 520mm 520mm 350mm 13 3/4" 13 3/4"26" 350mm 350mm660mm O 10" 250mm OD G a 7 3/4" 10" 190mm O 250mm OD G GG 10" OD OD 7 3/4" O 10" O 250mm 250mm 190mm 7 3/4" 7 3/4" 190mm 190mm b a flue collar b mantle c flame height control knob d timer e control panel MUST BE LEFT REMOVA
Installation Clearances Bistro Home Oven Installation and Operation Manual IF THIS APPLIANCE IS NOT PROPERLY INSTALLED, A FIRE MAY RESULT. TO REDUCE THE RISK OF FIRE, FOLLOW THESE INSTALLATION INSTRUCTIONS. A MAJOR CAUSE OF APPLIANCE-RELATED FIRES IS FAILURE TO MAINTAIN REQUIRED CLEARANCES (AIR SPACES) TO COMBUSTIBLE MATERIALS. DO NOT PACK REQUIRED AIR SPACES WITH INSULATION OR OTHER MATERIALS. IT IS OF THE UTMOST IMPORTANCE THAT THIS APPLIANCE BE INSTALLED ONLY IN ACCORDANCE WITH THESE INSTRUCTIONS.
Installation Clearances Bistro Home Oven Installation and Operation Manual EXAMPLES OF NON-COMBUSTIBLE WALL CONSTRUCTION Metal studs faced with cement board Concrete block wall Poured concrete wall EXAMPLES OF COMBUSTIBLE WALL CONSTRUCTION REQUIRING 1 INCH SIDE CLEARANCE Note: For clearance purposes, fire-rated Drywall is the same as standard Drywall.
Venting Bistro Home Oven Installation and Operation Manual All of the combustion products and cooking vapors from the WS-BH-4343, WS-BH-4355 and WS-BH-4836 models pass through the 10-inch diameter flue collar. These models may be connected to an 8-inch duct. The WS-BH3030 models are equipped with an 8-inch collar located atop the exhaust transition. The WS-BH-4343-RFG-W and BH-4355-RFG-W models may burn up to 3 lbs. of wood per hour and must be vented as a solid fuel burning piece of equipment.
Moving the Bistro Bistro Home Oven Installation and Operation Manual IF YOU NEED TO DISASSEMBLE THE OVEN TO MOVE IT THROUGH A NARROW DOOR OR PASSAGEWAY, SEE DISASSEMBLY SECTION. Bistro models are shipped fully assembled. The oven can be moved into place with a pallet jack using the LOWER forklift pockets. If the oven is to be installed against a wall, you may need to leave access to the back of the oven to complete the utility connections. NOTE: Rear panel MUST be installed.
Disassembly Bistro Home Oven Installation and Operation Manual If you need to disassemble the appliance to move it through a narrow door or passageway... 1. Both the interlock connection to the relay and the leads to the Temp Limit switch will need to be disconnected. The Temp Limit switch is located beneath the oven, just forward of the burner. Remove the flexible gas connector. Unplug the Temp Limit switch wire and coil it to prevent damage.
Disassembly Bistro Home Oven Installation and Operation Manual 2. Remove the (3) nuts and (2) carriage bolts that hold the mantle in place, and remove the mantle. It may be necessary to cut the silicone at the joint between the mantle and the appliance. 3. Remove the control box from the appliance. carriage bolt nut An ongoing program of product improvement may require us to change specifications without notice. Wood Stone Corporation 1801 W. Bakerview Rd. Bellingham, WA 98226 U.S.A. 14 tf. 800.578.
Disassembly Bistro Home Oven Installation and Operation Manual Using the upper forklift pockets, support the appliance with a forklift or other suitable device. Remove the bolts that attach the appliance body to the stand. Lift the appliance off of the stand and place it on blocks as shown in Step 1 on the following page. For Bistro 3030 models: forklift pockets are on the front only and do not extend all the way through the appliance. Disassemble the stand if necessary.
Lifting the Bistro Bistro Home Oven Installation and Operation Manual Moving a disassembled Bistro oven through a narrow door or passageway using the optional lifting system An optional Lifting System is available from Wood Stone to facilitate tipping the oven body onto its back and lifting it. When turned on its back, the upper oven portion of Bistro or Phoenix models 4343, 4355 and 4836 will be approximately 32 inches wide. This will allow for easier access through small passages.
Lifting the Bistro Bistro Home Oven Installation and Operation Manual 10. Once the oven is on the other side of the passageway, attach strap to the clevises at the Lifting Holes on the Crosspiece and, with a gantry crane, lift the oven straight up. Remove pallet jack. Lower the oven onto 4x4" blocks. 6. Attach strap to the clevises at the top of each Pickeye Insert. Using an appropriate hoist or lift, tilt the oven on its back, onto 4x4" blocks. 11.
Exploded Parts View Bistro Home Oven Installation and Operation Manual heat shield doors flame guard appliance body door posts mantle control box front panel perforated toe kick front or rear cross member with fork pockets side panels rear panel All parts shown above, rear panel included, provided with the appliance MUST be installed to ensure the safety and proper operation of the appliance.
Assembly Bistro Home Oven Installation and Operation Manual Follow these instructions only if the Bistro was shipped disassembled. 1. Lay out pieces. 2. Use the 3/8" x 1" carriage bolts to assemble the stand on a level surface. Be sure to use the washers provided and to tighten nuts and bolts securely. insert 3/8" x 1" carriage bolts On 3030 Models only: Use 3/8" x 3/4" carriage bolts to attach the sides instead of the 3/8" x 1" long carriage bolts.
Assembly Bistro Home Oven Installation and Operation Manual 3. Using a forklift, carefully lower the body of the appliance on to the stand so that the bolt holes line up. While supporting the appliance with the lift, install the 3/8" x 1" carriage bolts. Use the washers provided and tighten all nuts securely. Be sure to use the forklift pockets when lifting the body of the appliance. (Bistro 3030 models: forklift pockets are on the front only and do not extend all the way through the appliance.) 4.
Assembly Bistro Home Oven Installation and Operation Manual 5. Remove the shipping panel from beneath the appliance. The shipping panel is secured with (2) screws in the front, and (2) screws in the back. Discard the shipping panel. 6. Attach the control box to the appliance using (4) 1/4-20 screws. The control box should be oriented so the Flame Height Control Knob is on the left side of the control box. An ongoing program of product improvement may require us to change specifications without notice.
Assembly Bistro Home Oven Installation and Operation Manual 7. Connect burner assembly components, thermocouple and Temp Limit switch wires at the rear of the control box. Use the flexible gas pipe provided to connect the burner. Tighten the fitting firmly. Plug in the Temp Limit switch wire here. Plug in the thermocouple wire here. SV-2 gas valve. Plug in the igniter wires from the burner here. Attach the flexible pilot tube here. Tighten the fitting firmly.
Assembly Bistro Home Oven Installation and Operation Manual 8. Install the mantle. Install the (3) threaded studs into the clips on the front of the appliance. Slide the mantle over the studs, then slip one washer onto each stud. Install and tighten the nut caps onto studs securely. nut cap washer threaded stud If the appliance has been supplied with a granite mantle, affix the granite slab to the mounting bracket using a generous amount of the adhesive provided.
Assembly Bistro Home Oven Installation and Operation Manual 10. Reinstall the burner guard and log set. The lower tab of the guard fits into the front of the burner opening. Check that this did not shift during shipment and installation. The log set pieces fit onto the studs on the burner guard, behind the opening in the guard, so the logs sit at the rear of the burner opening. Continued on following page. An ongoing program of product improvement may require us to change specifications without notice.
Utility Connections Bistro Home Oven Installation and Operation Manual 11. Make utility connections at the rear of the control box. Gas and electrical connections must comply with all relevant local and national codes, and in a manner acceptable to the authority having jurisdiction. Make the electrical connection to the terminals in this junction box. Note: Correct voltage is specified on this junction box and the equipment data plate. Connect the incoming gas supply to the 3/4 inch FNPT gas inlet.
Utility Connections Bistro Home Oven Installation and Operation Manual The installation must conform with local codes, or in the absence of local codes with the National Fuel Gas Code, ANSI 223.1, NFPA 54, or Natural Gas Installation Code, CAN/CGA-B149.1, as applicable. The appliance and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psi.
Utility Connections Bistro Home Oven Installation and Operation Manual Fan / oven interlock relay instructions The interlock relay system is an option available from Wood Stone. With the interlock relay option, when the oven is turned on, the interlock relay is energized, allowing power to flow to the exhaust fan serving the oven. The fan will turn on with the oven. * Relay rated for 10 A. If fan current will exceed 10 A, use an additional motor contractor, installed after the relay.
Storage Box Installation Bistro Home Oven Installation and Operation Manual Item Part Number Rev Description 1 002-434310 6 Storage Box 2 1640571 0 Storage Box Connector Material Qty 1 installation of optional storage box for models BH-4343, BH-4355 and BH-4836 3 1640572 0 Toe Kick w/Perf (Does not apply to BH-3030) Stainless Steel, 304 1 Stainless Steel, 304 1 1. Install Toe Kick (w/ perforations) using (3) provided 1/4-20 screws (a). 2.
Outdoor Installation Bistro Home Oven Installation and Operation Manual All Mountain Home ovens are approved for outdoor installation. The unit may be installed in a weatherproof enclosure. If so be sure to maintain all clearances and adhere to the installation requirements included in this manual.
Mantle Stone Installation Bistro Home Oven Installation and Operation Manual On-site installation of mantle stone Bistro Home ovens can be ordered with the optional Mantle Bracket to facilitate the installation of a custom granite (or similiar stone) mantle on-site. The installation process is described below. mantle bracket mantle bracket faceplate 1. Remove the two Swinging Doors by sliding them up over the Door Posts. Put in a safe place. 2.
Mantle Stone Installation Bistro Home Oven Installation and Operation Manual 3. Remove Door Post hardware by following the steps below. 3a. Remove the Set Screw from the top of each post. Put in a safe place. 3b. Pull ou the Door Restraining Pin. Put in a safe place. 3c. Slide the Brass Flange up to remove. Put in a safe place. 4. Dry fit the stone to ensure proper fit. Apply a generous amount of silicone adhesive to the top of the Mantle Bracket.
Mantle Stone Dimensions Bistro Home Oven Installation and Operation Manual Mantle stone dimensions Tolerances: Linear ±1/16 [±1mm], Angular ±2° Note: Because of the possibility of slight production derivations, we recommend using these dimensions as approximations, and taking final measurements on-site.
Controller Bistro Home Oven Installation and Operation Manual Hearth temperature The floor (hearth) temperature will be displayed here any time the unit is turned on. Sensor is embedded 1" below hearth surface. Display will read “LO” when the temperature is below 100 °F. Temperature units Press and hold to switch between Fahrenheit and Celsius. ON/OFF button Press to turn unit on and off. Flame Height Control Knob Use this knob to raise/lower the flame to control the appliance temperature.
Operation Bistro Home Oven Installation and Operation Manual NOTE: The ceramic materials used in the construction of your Wood Stone oven will absorb moisture if exposed to high humidity or damp conditions during shipment from the factory or extended periods of storage before installation. Occasionally, through the course of the initial startup, as the oven heats up it is possible that you will see some water dripping from the sides of the oven as this moisture is driven out of the ceramic.
Operation Bistro Home Oven Installation and Operation Manual GENERAL OPERATION The appliance floor temperature is displayed on the controller readout. 1. Turning on the appliance Push I/O button and turn the radiant flame to its highest setting. To set the appliance to turn on automatically using the programmable timer, see the programming section of this manual. 2. Heat-up The appliance should reach cooking temperatures of 550–575 °F in 3 to 3-1/2 hours.
Operation Bistro Home Oven Installation and Operation Manual 4. Cleaning the appliance interior As needed, use the natural fiber brush to sweep stray food debris to the corner near the doorway, where it can be easily removed when you are finished cooking or once the appliance is cool. As needed, swab the deck using a damp (not wet) rag wrapped around the floor brush. This is best to do when the appliance is hot. Take care to avoid brushing debris into the radiant flame burner.
Maintenance Bistro Home Oven Installation and Operation Manual Wood Stone recommends the use of the natural fiber brush for sweeping aside excess food particles that will accumulate on the floor of the appliance during use. The appliance floor can be cleaned with a damp rag. DO NOT USE ICE OR EXCESSIVE WATER ON THE FLOOR; THIS IS TO PREVENT THERMAL SHOCKING OF THE STONE. There is a stainless steel burner guard to prevent food from falling on and thereby obstructing the gas orifices of the radiant flame.
Wood Burning Bistro Home Oven Installation and Operation Manual Wood and Ash Wood should be stored and handled in accordance with the recommendations outlined in NFPA 96. The interior floor and dome of the appliance do not require creosote or soot removal. The appliance flue and exhaust system will require inspection and cleaning. The exhaust system should be inspected and cleaned per the manufacturer’s and or local code official’s recommendations. Dispose of ash per the following: 1.
Troubleshooting Guide Bistro Home Oven Installation and Operation Manual Problem Cause/Solution Controller will not turn on 1. Incoming power to appliance turned off. Check circuit breaker for circuit supplying the appliance. Check that any wall switches external to the appliance that control appliance power are turned on. Check that any interlocks external to the appliance are turned on. 2. If control still does not turn on, please contact Wood Stone for assistance. Flame does not light 1.
Programming Bistro Home Oven Installation and Operation Manual On/Off buttons display Hr/Mn buttons Clock/Timer Programming NOTE: If an exhaust fan is installed on the appliance ventilation system, it must be interlocked to the appliance. An unsafe condition will result if the appliance is programmed to start automatically without the exhaust fan running. If an exhaust fan is installed it must be running whenever the appliance is turned on. See the Interlock Relay section for a diagram.
Programming Bistro Home Oven Installation and Operation Manual Timer Mode Operation When the timer is programmed for “ON/OFF” mode operation and the time of day reaches the programmed 'ON' time, the appliance controls will be switched on and the clock face icon will flash until the off time is reached, at which time the clock face icon will go off.
Fuelwood Facts Bistro Home Oven Installation and Operation Manual What type of wood should you use to fire your solid fuel cooking equipment? The answer to this question depends on several considerations: geographical location, availability and relative cost of various fuelwood species and individual preferences regarding the flavor qualities of various wood types. There are a wide variety of good fuelwood species in all geographic locations. Each species of wood has different characteristics.
Electrical Diagram interlock diagram Bistro Home Oven Installation and Operation Manual Bistro with hot surface ignition and timer Single RFG XFMR Junction Box L N G CB 4A Blue or Pink Yellow GND 110-120 VAC 50/60Hz wired by others Clock / Timer Circuit Board Temperature Controller Control Panel Type 4 Thermo Couple - + 1 1 2 3 4 5 6 2 3 4 5 6 7 8 9 10 Red Yellow Red White Orange Brown White Brown Remote SV2 Radiant Bellingham, WA +1(360)650-1111 www.woodstone-corp.
Limited Warranty Bistro Home Oven Installation and Operation Manual ALL WARRANTY SERVICE MUST BE PRE-APPROVED BY WOOD STONE PLEASE CONTACT THE FACTORY FIRST Please call 800.578.6836 or 360.650.1111. Our normal business hours are 8am to 5pm (PST) with service hours until 4:30pm, Monday through Friday.