WOODBRIDGE R ELECTRONIC TOILET SEAT ( 9 : Installation Manual Thank you for choosing our products.Please read the instructions carefully before installation and keep it available for future maintenance or reference. Our company reserves the right of final interpretation for this manual. The manual is subject to change without notice.
READ ALL INSTRUCTIONS BEFORE UNPACKING THE PRODUCT INSTRUCTIONS THAT, IF IGNORED COULD RESULT IN DEATH OR SERIOUS INJURY CAUSED BY INCORRECT HANDLING OR INSTALLATION OF THE PRODUCT. THESE INSTRUCTIONS MUST BE OBSERVED FOR SAFE INSTALLATION.
IMPORTANT SAFEGUARDS When using electrical products, especially when children are present, basic safety precautions shouldalways be followed, including the following: 1.The appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction. 2.Children being supervised not to play with the appliance. 3.
IMPORTANT SAFETY INSTRUCTIONS CAUTION – Indicates that failure to follow the instruction may cause body injury or property damage. 1. Do not install or use the product in wet places as steam room etc.This product must be connected to properly grounded power outlet socket. 2. It is recommended to use water-proof electrical outlet which should be lnstalled in the place where is not easily got wet. 3. This product should be used with AC 110V-120V,50/60Hz electrical current only,load current is at least 15A.
Technical Specification Main Unit Rating pressure AC 110-120V,50/60Hz Rating power 1050-1250W Water pressure range Minimum water pressure 0.07MPa (20L/min. flowing pressure). Maximum water pressure 0.8MPa (Hydrostatic pressure) Electrical wire length is about 1.
Packaging List Remote Control Panel Parts USE R2 R1 USE DRY NT FRO R REA MAS SAG E N ITIO POS RE SSU PRE STO P SEAT ER WAT DRY LE NOZZ NING CLEA ENERGY SAVER Base plate pcs Base Plate Parts pcs pcs pcs pcs Water Supply Assembly pcs Installtion Manual Warranty Card Installation paperboard Main Unit 04 Installtion Manual Warranty Card Installation paperboard Installtion Manual Warranty Card Installation paperboard
Main unit identification Lid Water inlet connector Water discharging cover Side receiving window Main unit button Main unit disassembly button Socket Remote control receiving window Power indicator Energy saving indicator Wand Seat Hole for rear cleaning Drying device Base plate Night light Spray nozzle Hole for ladies’ front cleaning 05
Installation lnstruction Installation dimension Note:please check if the installation dimension matching the user’s toilet. Installation of mounting plate Press the expansion nuts into the installation holes in the toilet,then install the base plate, plastic plates,flat washers and bolt as per the drawing and tighten the bolts. The black pin frontward and groove upwards.
Installation and disassembly of main unit Disassembly Press the “removal button” on washlet, until a “click” is heard,and pull it out. Installation Push the washlet back onto the base plate until a “click” is heard. Installation Note: Before pulling out the washlet,release hand from “removal button”. Disassembly Connecting the water supply pipe 2.Bottom inlet:Connect water supply on 1.
Installation instruction Checking the power and water supply Connect the water supply hose and turn on the angle valve.Check if any leakage. Insert power plug into power socket. Indicator light Electric leakage test button Water tank Press protection switch Grounded outlet Protection switch Grounding pin CASE 1 NOTE: If it’s an electric leakage protection plug,press protection switch, indicator light is on which means there is electricity.
Function illustration of keys in main unit and actuator 1. Long press “Power” button to enter standby mode; and then quick press “Power” button to restore functional mode. 2. When people sit, press “Power” button to stop the Power function of rear, front cleaning or drying. When no one sits, press “Power” button to switch between function mode and power save mode.
Daily maintenance Main unit maintenance 1.Shut off power supply at maintenance. 2.Turn the seat upward open,press down the button located on the right side of main unit and pull out the seat.Wipe the stain with a soft damp cloth. 3.AfteX cleaning re-install the seat back to main unit. Note: Do not pour the water on the product at maintenance. Spray nozzle maintenance Do the following to clean the wand. 1.Press “nozzle cleaning” or “rear cleaning” button for a while and wand will come out.
Inlet filter cleaning 1.Pull out electrical plug,then shut off water supply valve and remove water supply hose. 2.Remove the filter.Use the brush to clean the filter. 3.Put the filter back into inlet after cleaning.Then connect the water supply pipe. Remove the filter. Use the brush to clean the filter. Tank anti-freezing and anti-bacterial maintenance When room temperature is under zero and electricity is disconnected,or user is away for a long time.The water inside the tank should be discharged.
Troubleshooting Guide Problem No flushing Cause Water supply hose buckling causes block The water is not hot Seat temperature is not hot Wind temperature is not hot No wind out Spray wand cannot retracted Spray wand cannot stretch out Controller cannot display Solve the buckling Fill valve is off Turn on the fill valve Water supply is cut off Connect water supply and wait for the water Solve the buckling Water supply hose buckling causes partial block Poor flushing Solution Fill valve is not ful
Please contact us if you have any questions. Customer Service Phone: 562-774-2284. Or email : help.woodbridge@gmail.com The picture of product may not entirely consistent with actual appearance and color because of products improvement, please in kind prevail.
