WS-TS-1500 WS-TS-2000 WS-TS-2500 www.woodprostoves.com 1-877-427-3316 www.woodprostoves.com www.woodprostoves.
SAFETY INSTRUCTIONS 1. The installation of this stove must comply with your local building code rulings. Please observe the clearances to combustibles (see reference ſIWTGU 4–8). Do not place fuel, furniture or any other objects within the clearance area. 2. Verify that the stove is properly assembled and installed before ſring the stove for the ſrst time.
SAFETY INSTRUCTIONS 18. During the ſrst 12 to 15 ſres the special paints and protective oils used in construction of your stove may give off some smoke and odor while they are curing. This should disappear after a short period of time and not occur again. Persons with lung conditions or owners of susceptible domestic pets (such as birds) should take prudent precautions. Open windows and doors as needed to clear smoke and/or odor. Paint discoloration will occur if the stove is ovGT ſTGF 19.
TABLE OF CONTENTS SAFETY INSTRUCTIONS ............................................................................. 1 – 3 TABLE OF CONTENTS ..................................................................................... 4 LOCATING THE STOVE ....................................................................................5 MINIMUM CLEARANCES with SINGLE-WALLED PIPE ...................................6 MINIMUM CLEARANCES ALCOVE and DOUBLE-WALLED PIPE ...................7 ASSEMBLY INSTRUCTIONS .......
LOCATING THE STOVE ſrmly hold the pipe sections together. DO 0OT 1. The stove must be placed on solid concrete, solid %100'%6 THIS STO8' TO #0; AIR DISTRIBUmasonry, or when installed on a combustible ƀQQr, 6+10 14 &7%6 5;56'/ on an Underwriters Laboratories Listed Type 2 ƀoor protector listed to UL standard UL 1618, such as 6. Recheck clearances from the stove, con Hy-C or Imperial Model UL4056BK.
Minimum Clearances for installation according to UL 1482 (US) & ULC-S627 (CAN) A 6
Top Alcove A A 7
BLOWER ATTACHMENT philips GASKET A (4 places) 8
WS-TS-2500 23 8 6 9
6 10
CONNECTOR PIPE SIZING NOTE: CONNECTOR PIPE IS NOT INCLUDED. TO PURCHASE, VISIT YOUR LOCAL HARDWARE, HOME, OR BUILDING CENTER. ADDITIONAL SPECIFICATIONS. Connector pipe is used to make the connection from the ſPCN positioning of your stove to an approved chimney. Connector pipe is NOT KPENWFGF as part of the stove. Connector pipe must be 6”/152mm diameter minimum of 24 MSG (minimum standard gauge) bNCck or 26 MSG bNWG UVGGN UVove pipe.
02%,/( +20( ,167$//$7,21 ,16758&7,216 ^ X']J = * * < + ! " # * ; =* ſVVGF # " $ %' _ * ~ '^X']J ' *+ ; < = >* ][' + + + ' _
CHIMNEY CONNECTIONS The stove must be connected to either a lined masonry or manufactured metal chimney built and tested VQ VJG URGEKſECVKQPU NKUVGF QP VJG RTevious pages. Chimneys perform two functions: . As a means of exhausting smoke and ƀWG gases which are the result of fuel combustion. . The chimney (only provides “draft” which allows oxygen to be continuously introduced into the appliance, so that proper combustion is possible. This stove relies on natural draft to operate.
...continued CHIMNEY CONNECTIONS MANUFACTURED CHIMNEY REFER TO CHIMNEY AND CHIMNEY CONNECTOR MAKER’S INSTRUCTIONS FOR INSTALLATION AND USE. Use only Ŋ OO FKCOGVGT OCnufCEVWTGF EJKOney sysVeO lisVed Vo UL 03 HT (US) oT ULC-S6 9 (CAN). %JKOPey OCFG VQ VJKU NKUVKPI is *KIJ TGORGTaVWTG TCVGF VQ u( uC. Use EJKOPey HTQO only one OCnufCEVWTGT. NevGT OKZ bTands. %CTGHWNN[ follow VJG EJKOPey OCnufCEVWTGTŏs UVCVGF TGSWKTGOGPVU and cleaTances.
...continued CHIMNEY CONNECTIONS VKſGF ChimnGy SwGGp, or a knoYNGFIGCbNG KPURGEVQr. Consult your insurCPEG EQORCny if you ECPPQV ſPF a SWCNKſGF GZRGrt. CAUTION: NOT ALL FIREPLACE CHIMNEYS ARE SUITABLE FOR CONVERSIONTO ACCOMMODATE CONNECTION TO A WOOD STOVE. CHECK WITH A QUALIFIED EXPERT. Many prGfabriEatGF ſrGplaEGs arG of thG “zGroENGCranEG ſTGplaEG” ECtGIory. ThGsG Eonsist of multi layGrGF mGtal EonstruEtion.
CHIMNEY CONNECTOR SYSTEMS & CLEARANCES NFPA 211 (US) NOTE: In Canada, installation must conform to CAN/CSA-B365 when passing through combustible construction. A. Brick Masonry Minimum Ŋ OO thick brick masonry all framed into combustible wall with a minimum of 1 Ŋ 305mm brick separation from clay liner to combustibles. The ſTGENay liner shall run from outer surface of brick wall to, but not beyond, the inner surface of chimney ƀWG liner and shall DG ſrmly cemented in place. B.
OPERATING INSTRUCTIONS CAUTION: HOUSE FIRE HAZARDS TOR, UNDERNEATH STOVEPIPE, OR ANYWHEREWITHIN MINIMUM CLEARANCES FROM COMBUSTIBLE SURFACES SPECIFIED FOR THIS STOVE. YOU ARE OVER FIRING IF A UNIT OR CHIMNEY CONNECTOR GLOWS RED. OPERATING SAFETY PRECAUTIONS 1. NEVER OVER FIRE THIS STOVE BY BUILDING EXCESSIVELY HOT FIRES AS A HOUSE/ BUILDINGFIREMAYRESULT.YOUARE OVER FIRING THE STOVE IF UNIT OR STOVEPIPE BEGINS TO GLOW OR TURN RED. 2.
OPERATING INSTRUCTIONS height, weather, log size, wood species and moisture content. Some experimentation will initially be required to ſnd that “sweet spot” where your stove performs best. The following will give you a starting point to ſPF your optimum settings. When ſrst loading fuel set the primary air inlet control (center) at the wide open (Pull out) position for at least 15–20 minutes (the high burn duct control should be closed – pulled out – when starting ſTGU .
OPERATING INSTRUCTIONS ...continued Fuel load size can vary but should be kept Ō Ŋ 7. Once fuel has been loaded, close the door and leave the air inlet control fully open until ſTG is well (25mm-50mm) below the secondary air tubes. Also established (at least 15–20 minutes) being careful position the fuel to leave space so the air from the inlet not to over ſTG (if any of the exterior parts of the can work between the pieces of fuel.
SERVICE HINTS WARNING: REPLACE GLASS ONLY WITH 4MM HIGH TEMPERATURE CERAMIC GLASS OF THE PROPER SIZE. DO NOT USE SUBSTITUTE MATERIALS SUCH AS TEMPERED GLASS OR DOUBLE THICKNESS WINDOW GLASS! CONTACT THE STOVE MANUFACTURER FOR REPLACEMENT GLASS. Gasket and Glass cleaning products are available at local retail home centers. Manufacturers of cleaning products include, A.W. Perkins Co. (www.awperkins. com) or Rutland Products (www.rutland.com).
BAFFLE REMOVAL 23
BAFFLE REMOVAL 24
SERVICE PARTS 25
SERVICE PARTS 26
SERVICE PARTS 27
SERVICE PARTS 28
SERVICE PARTS 29
SERVICE PARTS 30 WS-TS-2500
BLOWER MAINTENANCE & WIRING DIAGRAM BLOWER MAINTENANCE The optional blower is maintenance free other than cleaning. Lightly vacuum motor and air inlet to keep free of dust and dirt. DANGER:SHOCK HAZARD.DISCONNECT POWER SOURCE BEFORE INSTALLATION AND WHENEVER SERVICING BLOWER ASSEMBLY. CAUTION: MOVING PARTS CAN CAUSE INJURY. DO NOT OPERATE WITH COVER REMOVED. NOTICE: ANY REPLACEMENT WIRING MUST HAVE E Q U I VA L E N T I N S U L A TION AND TEMPERATURE RATING (105°C).
FLOOR PROTECTOR MATERIAL CALCULATIONS This stove has been tested for and must be installed on a ƀQQT protector with the proper Thermal Resistance or R-value as stated in step 1 of the installation instructions under “Locating Stove” section of this manual. If the ƀQQT protector materials listed in the instructions are not available, materials with an equivalent R-value may be substituted.
CHIMNEY & STOVE MAINTENANCE LOG DATE OF SERVICE 33 PERFORMED BY DESCRIPTION
Warranty WoodPRO Wood Secondary tubes, baŋĞ͕gaskets 3 34 Firebodž͕Ňue collar, front door,ash door
Warranty 35
www.woodprostoves.
