VR48A - SN 71111004 & After VR66A - SN 144591004 & After VR73A - SN 153661104 & After (Rev. 5/16/2008) MAN0357 VR84A - SN 330591004 & After Tested. Proven. Unbeatable.
TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Woods® dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual are completed before releasing equipment to the owner. The dealer must complete the Product Registration online at the Woods Dealer Website or complete the mail-in form included with the Operator’s Manual.
TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 SAFETY INSTRUCTIONS & DECALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIFICATIONS VR48A VR66A VR73A VR84A Drum Width 48 inches (129 cm) 66 inches (168 cm) 73 inches (186 cm) 84 inches (215 cm) Drum Diameter 23 inches (59 cm) 23 inches (59 cm) 23 inches (59 cm) 23 inches (59 cm) Drum Oscillation ±7.5° ±7.5° ±7.5° ±7.5° 3100 lbs. 3100 lbs. 3600 lbs. 3600 lbs. 2000 @ 21.3 gpm 2000 @ 21.3 gpm 2000 @ 21.3 gpm 2000 @ 21.3 gpm 24 gpm (64 lpm) 24 gpm (64 lpm) 24 gpm (64 lpm) 24 gpm (64 lpm) 16 oz. 20 oz. 24 oz. 28 oz.
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to provide safe equipment can be wiped out by an operator’s single careless act. In addition to the design and configuration of equipment, hazard control and accident prevention are dependent upon the awareness, concern, judgement, and proper training of personnel involved in the operation, transport, maintenance and storage of equipment.
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! (Safety Rules continued from previous page) Always wear relatively tight and belted clothing to avoid getting caught in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate. Be sure attachment is properly secured, adjusted, and in good operating condition.
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! MAINTENANCE Before leaving operator's seat, lower lift arms and put attachment on the ground. Engage brake, stop engine, remove key, and remove seat belt. NEVER GO UNDERNEATH EQUIPMENT. Never place any part of the body underneath equipment or between moveable parts even when the engine has been turned off.
SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! See exploded view drawing on page 16 for decal locations. 30 - Serial Number Plate MODEL NO. 52 - PN D0197 SERIAL NO. Woods Equipment Company Oregon, Illinois, U.S.A. 42 - PN 19924 WARNING HIGH-PRESSURE HYDRAULIC OIL LEAKS CAN PENETRATE SKIN RESULTING IN SERIOUS INJURY, GANGRENE OR DEATH. n Check for leaks with cardboard; never use hand.
OPERATION The Vibratory Roller is a hydraulically powered attachment intended to compact soil, stone, or fill material. The performance of the attachment can vary greatly depending on how it is used and operated. Therefore, the recommended operating procedures in this manual should be followed at all times for maximum productivity. When attaching the unit to the skid steer, ensure that all hydraulic hoses are coupled securely to the quick couplers. Prior to operating the attachment, read this entire manual.
OWNER SERVICE A WARNING ■ Before performing any maintenance or service on the unit, perform the mandatory safety shutdown procedure. MAINTENANCE Proper maintenance of the attachment will result in longer life and more productive and cost effective operation. DRUM REMOVAL 1. Securely support the roller chassis in the front and rear on both sides with the drum resting firmly on the shop floor. 2. Remove the motor guard and motor, and allow the lubricant to drain from the roller shaft. 3.
6. Remove the outer bearing housing mounting hardware (55 & 57). See page 16. 7. Slide the outer bearing housing (28) out of the drum. If needed, use threaded holes (1/2" UNC) in the housing to unseat it from the drum weldment, Figure 5. 8. Remove the outer bearing housing mounting hardware on the motor end. 9. Slide the bearing housing assembly and the shaft out of the drum. 14 Figure 2 4. Remove the shaft nut (13, using part number 1023106 socket), the shaft washer, and the tongued washer (27), Figure 3.
BEARING INSTALLATION 1. Apply a small amount of lubrication (oil or grease) to the outer bearing housing. 7. Insert the shaft into the drum and clamp the outer housing to the drum. 2. Assemble the outer bearings to the inner bearings using an industrial press. Figure 9 Figure 6 3. Install one of the housing assemblies to the shaft. 8. Clamp the remaining housing assembly together using washers and bolts in the threaded holes in the outer housing. Be sure bolts do not protrude through the outer housing.
Spring Retaining Ring DP13 Figure 13. Seal Removal Install Seal and Bearing DP11 1. Clean area in housing where seal outer diameter (OD) seats. Apply a thin coat of Permatex®. Figure 11. Remove Spring Retaining Ring 4. Firmly grasp the top of the shaft and pull assembly from motor. 5. Remove snap ring (Figure 12) from the shaft and slide spacer and bearing from shaft. Save snap ring and spacer for later use. 2. Inspect area of shaft where seal seats. Remove any burrs or nicks with an emery cloth. 3.
NOTES 14 Owner Service MAN0357 (Rev.
TROUBLESHOOTING PROBLEM PROBLEM CAUSE Insufficient compaction SOLUTION Loader “down pressure” insufficient Increase the “down pressure” by raising the front wheels off the ground (see Operation). Vibration circuit pressure insufficient Adjust the bypass pressure (screw on top of valve) to 1000-1100 psi (69-76 bar). See exploded view, page 16. Excessive vibration Vibration circuit pressure excessive Adjust the bypass pressure (screw on top of valve) to 1000-1100 psi (69-96 bar).
VIBRATORY ROLLER GENERAL ASSEMBLY REF PART QTY DESCRIPTION 1 105382 1 Chassis weldment, VR48A 1 105373 1 Chassis weldment, VR66A 1 105374 1 Chassis weldment, VR73A 1 105420 1 Chassis weldment, VR84A 2 102089 1 Attach frame, VR48A 2 101528 1 Attach frame, VR66A 2 101528 1 Attach frame, VR73A 2 101528 1 Attach frame, VR84A 3 101423 1 Bushing, 2.562 x 2 x 2.125 16 Parts (Rev. 4/4/2008) MAN0357 (Rev.
VIBRATORY ROLLER GENERAL ASSEMBLY REF 4 4 4 4 4 4 4 4 5 5 5 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 35 36 37 38 39 40 41 42 43 PART 101711 101434 101444 102832 101712 101713 101714 104047-1 102629048 102629066 102629073 102629084 102574 101234 101233 105801 101210 101217 101213 101208 106655 106730 313017 F1210 31982 B0624 1007697 1007698 1007696 1012105 61 102886 105671 106656 105800 105664 ----------------101232 106668 106669 M0036 101437 21660 M0008 * B162
OPTIONAL FLOW CONTROL KITS REF 1 PART 1007693 QTY 1 DESCRIPTION Priority flow 17 gpm (used in kit 1012103) 1 1007694 1 Priority flow 23 gpm (used in 1012104) 2 1007695 1 Priority flow block 3 1012100 1 Guard, valve VRA 4 F1025 1 Fitting, 8 OM x 8 FLM 90° 5 316017 2 Fitting, 12 OM x 8 FLM ST REF PART QTY DESCRIPTION 6 F1231 1 Fitting, 8 FLM x 8 FLF x 8 FLM 7 8 9 10 11 12 13 14 37501 1004288 62176 * H1252 H1256 565 * 835 * 31138 * 1 1 1 1 1 4 2 2 Fitting 12 OM x 8 FLM 90° E
BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly.
BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. SAE Bolt Thread Sizes 5/16 3/8 1/2 IN MM 5/8 3/4 7/8 1 2 3 4 5 6 7 25 50 75 100 125 150 175 Metric Bolt Thread Sizes 8MM 10MM 12MM 14MM 16MM 18MM ABBREVIATIONS AG .............................................................. Agriculture ASABE ....................American Society of Agricultural & Biological Engineers (formerly ASAE) ASAE.......
WARRANTY (All Models Except Mow’n Machine TM Zero-Turn Mowers and Woods BoundaryTM Utility Vehicles) Please Enter Information Below and Save for Future Reference. Date Purchased: ____________________________ From (Dealer): ___________________________________________ Model Number: ____________________________ Serial Number: ___________________________________________ Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship.
WARRANTY (Replacement Parts For All Models Except Mow’n MachineTM Zero-Turn Mowers and Woods BoundaryTM Utility Vehicles) Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship for a period of ninety (90) days from the date of delivery of the product to the original purchaser with the exception of V-belts, which will be free of defect in material and workmanship for a period of 12 months.
