(9/23/2005) MAN0472 For Woods BH70X, BH80X Backhoes HIS T E ! SAV NUAL MA e it withnual. a ud Incl khoe M fety, Bac ins sa epair r u yo conta and r not , It n n o o i i at rat ope inform other part und in ls. fo ua man Tested. Proven. Unbeatable.
TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Woods® dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual are completed before releasing equipment to the owner. The dealer must complete the Product Registration included with this manual. The customer must sign the registration which certifies that all Dealer Check List items have been completed.
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! ! LEA EL INSTRUCTIVO! Si no lee Ingles, pida ayuda a alguien que si lo lea para que le traduzca las medidas de seguridad. Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to provide safe equipment can be wiped out by an operator’s single careless act.
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! (Safety Rules continued from previous page) Always wear relatively tight and belted clothing to avoid getting caught in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate. Make sure attachment is properly secured, adjusted, and in good operating condition.
BACKHOE 3-POINT MOUNT INSTALLATION TRACTOR PREPARATION NOTE: For installing this 3-point mounting kit, reference to right, left, forward and rearward directions are determined from the operator’s position in the backhoe seat. TRACTOR HIGH STRENGTH TOP LINK PIN NOTE: Leave all hardware loose until mounting kit has been fit up. 40" Minimum Radius 1. Refer to the WOODS BH70X/BH80X Backhoe Operator’s Manual for backhoe assembly instructions. HEAVY-DUTY TOP LINK 2.
Attach Top Link Bars to Backhoe 1. Attach top link bar (3) to the main frame using cap screw (8), hardened flat washer (15), and hex nut (11). 2. Slide double top link (1) over top link bar (3) and secure using cap screw (10), hardened flat washer (15), and hex hut (11) through end hole on double top link. See Figure 3. 1. 1007345 Double top link 3. 1012532 Top link bar 8. 12558 3/4 NC x 4-1/2 HHCS GR5 10. 14334 3/4 NC x 3 HHCS GR5 11. 1450 3/4 NC Hex nut 15.
Attach 3-Point Mount to Backhoe 3. Attach lock bar (7) to right (4) and left (5) rear brackets using cap screws (9), four (two per side) hardened flat washers (15), and hex nuts (11). Do not tighten nuts at this time. 8 15 4. Swing lock bar up and attach it to the double top link bar using cap screw (8), hardened flat washer (15), and hex nut (11). See Figure 5. 11 7 11 4. 1012534 Right rear bracket 5. 1012535 Left rear bracket 7. 1012582 Lock bar 8. 12558 3/4 NC x 4-1/2 HHCS GR5 9.
Attach Backhoe to Tractor (Continued) 5. Connect tractor 3-point lower lift arms to the mounting pins on the backhoe. Secure using klik pin (14) and washers (17). Use washers to take up slack between klik pin and 3-point arm. See Figure 7. 6. Connect double top link bar to the tractor top link bracket. Use top link pin supplied with your tractor and sleeve (12). If necessary, separate and adjust top link bars IN or OUT to maintain the backhoe vertical position.
Remove Backhoe DANGER The only time the backhoe may be operated from a position other than the operator seat is during backhoe attachment and removal. Operator must • Read Mounting Kit Manual instructions on attaching and removing backhoe and use extreme care. • Always stand between rear tire and backhoe stabilizer arms or along side of tractor to avoid being trapped should the boom swing control be accidentally activated. BH1 6" Blocks Figure 9. Backhoe Storage Position (Typical) 1.
Attach Backhoe to Tractor DANGER This mounting kit is designed to provide secure mounting and adequate operator clearance when properly installed. Check clearance dimensions shown in Figure 1 to be sure you have installed mounting kit correctly. Follow all mounting instructions in this manual. Do not operate backhoe unless there is adequate clearance. Failure to check and comply with these instructions may result in serious injury or death. 1. Remove the backhoe seat assembly. 2.
Tractor Connections 2-1/2" Max. 1 There may be more than one hole provided in tractor top link attachment bracket. Select hole A, B, or C that most evenly distributes the load between top link bracket top and bottom mounting bolts. See Figure 10. 2 A For the Massey Ferguson 1455V tractor use hole position D. NOTE: The maximum width between tractor top link attachment plates must not exceed 2-1/2 inches. This will prevent excessive bending loads to the tractor top link pin.
1012552 3-POINT MOUNTING KIT 8 12 1 10 15 11 8 15 11 3 15 7 11 15 11 9 16 15 15 17 6 4 14 CD6779 13 5 REF PART QTY DESCRIPTION REF PART QTY DESCRIPTION 1 1007345 1 Double top link 10 14334 * 1 3/4 NC x 3 HHCS GR5 3 1012532 1 Top link bar 11 1450 * 5 3/4 NC Hex nut 4 1012534 1 Right rear bracket 12 30067 1 Sleeve, .765 x 1.0 x 1.
BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly.
BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. SAE Bolt Thread Sizes 5/16 3/8 1/2 IN MM 5/8 3/4 7/8 1 2 3 4 5 6 7 25 50 75 100 125 150 175 Metric Bolt Thread Sizes 8MM 10MM 12MM 14MM 16MM 18MM ABBREVIATIONS AG .............................................................Agriculture NC .................................................... National Coarse ATF ..............................
WARRANTY (All Models Except Mow’n Machine TM Zero-Turn Mowers and Woods BoundaryTM Utility Vehicles) Please Enter Information Below and Save for Future Reference. Date Purchased: __________________________ From (Dealer): ________________________________________ Model Number: __________________________ Serial Number:________________________________________ Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship.
WARRANTY (Replacement Parts For All Models Except Mow’n MachineTM Zero-Turn Mowers and Woods BoundaryTM Utility Vehicles) Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship for a period of ninety (90) days from the date of delivery of the product to the original purchaser with the exception of V-belts, which will be free of defect in material and workmanship for a period of 12 months.