CZ1736K 872291F 17HP KAW W/36” SIDE DISCHARGE CZ2048K 872298F 20HP KAW W/48” SIDE DISCHARGE CZ2252K 872299F 22HP KAW W/52” SIDE DISCHARGE CZ2361B 872404F 23HP B&S W/61” SIDE DISCHARGE CZ2461K 24HP B&S W/61” SIDE DISCHARGE REV A 12-2009 MAN0820 872405F RF4164852 (Rev.
CALIFORNIA WARNING Proposition 65 Warning Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects and other reproductive harm. The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.
WOODS IMPORTANT MESSAGE TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Woods® dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Set-Up instructions are completed before releasing equipment to the owner. The dealer must complete the Product Registration online at the Woods Dealer Website or complete the mail-in form included with the Operator’s Manual.
WOODS TABLE OF CONTENTS FIGURES PAGE SAFETY........................................................................................................................................................ 5-11 SET-UP INSTRUCTIONS...........................................................................................................................12-13 LABELS......................................................................................................................................................
SAFETY WOODS NOTICE !!! Unauthorized modifications may present extreme safety hazards to operators and bystanders and could also result in product damage. This symbol means: ATTENTION! BECOME ALERT! Your safety and the safety of others is involved. Woods strongly warns against, rejects and disclaims any modifications, add-on accessories or product alterations that are not designed, developed, tested and approved by Woods Engineering Department.
SAFETY WOODS PREPARING FOR SAFE OPERATION WARNING Operator preparation and training Read the Operation & Safety Manual - If an operator or mechanic cannot read English, it is the owner's responsibility to explain this material to them. If any portion of this material is unclear, contact your factory representative for clarification. - Become familiar with the safe operation of the equipment, operator controls and safety signs. Know how to stop the engine and attachments quickly in an emergency.
SAFETY WOODS Machine preparation OPERATING SAFELY - Check operator presence interlock system and brake operation. Adjust or repair any problems before using. In general - Use extra care when loading or unloading the machine into a trailer or truck. - Do not tamper with or defeat safety devices. Keep guards, shields and interlock safety devices in place and in proper working condition. They are for your protection. - Slow down and use caution when making turns and crossing roads and sidewalks.
SAFETY WOODS Starting Interrupting operation - Start only according to instructions in this manual or on the machine. - - Before attempting to start the engine, make sure: - the parking brake is on; - the PTO is disengaged; - the traction drive is in NEUTRAL. Before leaving the operator's position: - Park on level ground. - Disengage the PTO. - Set the parking brake. - Shut off the engine and remove the key.
SAFETY WOODS MANEUVERING SAFELY In general - Slow down before turning. - - Do not mow in reverse unless absolutely necessary. Always look behind and down for small children and pets before and during backing. Use extra care with grass catchers or other attachments. These can change the stability of the machine. - Remove obstacles such as rocks, tree limbs etc. - Avoid driving over obstacles such as ruts, holes, rocks and roots whenever possible. Be alert to dips and rises.
SAFETY WOODS WARNING MAINTENANCE SAFETY Blades In general - Mower blades are sharp and can cut. Use extra caution when handling. Remove obstructions with care. Wrap the blade(s) or wear gloves. - Be aware that rotating one blade on multi blade mowers can cause other blades to rotate. - Only replace blades. Never straighten or weld them. - Keep other persons away from blades. - Maintain machine according to manufacturer's schedule and instructions for maximum safety and best mowing results.
SAFETY WOODS BATTERY WARNING Battery acid is caustic and fumes are explosive and can cause serious injury or death. To reduce the risk of personal injury when working near a battery: - When working with battery acid, use protective equipment such as, but not limited to, goggles, face shield, rubber gloves and apron. - Avoid leaning over a battery. - Do not expose a battery to open flames or sparks. - Be sure batteries with filler caps are properly filled with fluid.
SET-UP INSTRUCTIONS WOODS Tools required for assembly - Wrecking bar Claw hammer Sockets: 1/2”, 15/16 Wrenches: 18mm, 1/2”, 9/16”, 3/4”, 15/16” Tire pressure gauge NOTE: All references below to the “right” or “left” are with respect to an operator at the controls. 1. UNCRATE UNIT a) Discard packing materials. Loosen the caster wheel axle bolts and bumper bolts to remove the shipping brackets. Discard shipping brackets. b) Re-install and tighten bumper bolts.
SET UP INSTRUCTIONS WOODS 4. FINAL PREPARATIONS - Check the engine and hydraulic oil levels. Top off with the correct oil if necessary. Use 10W30 motor oil for the engine. Use fresh, clean 20W50 motor oil for the hydraulic system. See engine operation manual for specified motor oil viscosity. - Charge battery and properly connect cables. See steps below. Battery acid is caustic. Fumes are explosive and can cause serious injury or death.
LABELS WOODS 14
LABELS WOODS 15
LABELS WOODS DECAL IS LOCATED UNDER FOOTPLATE.
LABELS WOODS 17
CONTROLS WOODS Keyswitch (K) - The keyswitch has three positions: OFF, RUN, and START. Insert the key and turn it clockwise to move the switch from OFF to RUN. Turn it further to START and hold to engage the starter. Release the key and the switch will return to RUN from START. Turn the key counterclockwise to OFF to stop the engine. Throttle (T) - Move the throttle lever forward to increase engine speed until the maximum governed engine RPM is reached.
CONTROLS WOODS FUEL SELECTOR VALVE (U) The fuel tank selector valve is located behind the seat. The fuel tank selector valve has three positions: Off: The tank selector is off when the lever points down. The selector should be off whenever the machine is transported or stands unused for any length of time. Shutting off the fuel supply avoids the possibility of flooding should any dirt get under the carburetor float needle.
CONTROLS WOODS Reverse movement - To move the machine straight back, pull both traction levers back equally from their neutral position. Reverse speed increases as the levers are moved back farther. Maximum reverse speed is reached when the levers hit the rear of the forward-reverse slot. When moving in reverse, pushing the levers forward slows the machine, and the machine stops when the neutral position is reached. NOTE: Reverse is spring loaded to return to neutral.
CONTROLS WOODS Parking brake (R) - Pull the parking brake lever up and back to put the parking brake ON. Push it forward and down to put the parking brake OFF. The parking brake must be ON to start the engine. It must also be ON to keep the engine running if the operator leaves the seat. The parking brake must be OFF to keep the engine running when a traction lever is moved out of neutral lock.
PRE-OPERATION CHECK LIST WOODS PRE-OPERATION CHECK LIST (OPERATOR’S RESPONSIBILITY) ___ ___ ___ ___ ___ ___ 22 Review and follow all safety rules and safety decal instructions. Check that all safety decals are installed and in good condition. Replace if damaged. Check to make sure all shields and guards are properly installed and in good condition. Be sure that either the discharge shield or complete vacuum attachment is installed. Check that all hardware is properly installed. and secured.
OPERATION WOODS FUELING - Fill fuel tank with good quality, clean, unleaded regular gasoline. Do not use hi-test fuel. Use a funnel to avoid spilling. WARNING OPERATOR PRESENCE Interlock System To start the engine: - The PTO switch must be OFF. - Both traction levers must be in the neutral lock position. - The parking brake must be ON. To operate the machine: 1. The operator must be in the seat or engaging the PTO will kill the engine. TO CHECK OR ADD FUEL: – Do it outdoors 2.
OPERATION WOODS OPERATING NOTES Driving - Practice at slow engine and travel speeds with the PTO off until fully familiar with the controls. 1. With the PTO disengaged, move the parking brake to OFF. - For normal cutting the throttle should be set at the full open position. By using the traction levers to speed up or slow down the machine during use, maximum control and cutting efficiency can be maintained. 2. Move both traction levers out of neutral lock.
OPERATION WOODS Cutting 1. Place the discharge chute in the down position or correctly fit a grass collector or mulcher plate. 2. Sit in the seat. 3. Start the engine. 4. Turn the blades on by pulling up on the PTO switch. Do not start the blades at full throttle. Instead, use the slowest throttle setting that will allow the engine to pick up the blade load to reduce the wear on the belts and electric clutch. 5. After the blades are rotating, set the throttle to maximum.
MAINTENANCE CHART WOODS MAINTENANCE OPERATION Maintenance is an ongoing job. These intervals are maximum times betw een maintenance operations. Perform more often under severe conditions.
MAINTENANCE RECORD WOODS NOTES ________________________________________________ ________________________________________________ ________________________________________________ ________________________________________________ ________________________________________________ ________________________________________________ ________________________________________________ ________________________________________________ ________________________________________________ _______________________________________
MAINTENANCE WOODS CHECK DAILY Operator Presence Interlock System - Start Operation For the engine to crank, the parking brake must be on, the PTO (blades) off and traction levers in the neutral lock position. Sit in the seat and check, one by one, if the engine will crank with the parking brake off, the blades on, and either traction lever out of neutral lock.
MAINTENANCE WOODS LUBRICATION Every 50 hours of operation, lubricate the following points (1-3) with grease: 1. Deck lift lever (1 point) 2. Deck lift pivots (4 points) 3. Pull arms (2 points located at the front of the cutterdeck) 4. Caster wheel pivots (2 points) (Lubricate every 500 hours or once a year) NOTE ON BLADE SPINDLES - The blade spindles on these machines use a superior sealed bearing that does not require relubrication.
MAINTENANCE WOODS ENGINE OIL Do not perform engine maintenance without the engine off, spark plug wires disconnected and PTO disengaged. AFTER FIRST FIVE (5) HOURS While the engine is warm: 1. Release the oil drain hose assembly from the engine clip J. Lay hose assembly over the frame edge or through the frame cutout, which ever is most convenient. 2. Remove the rubber cap D from the tip of the hose assembly and turn the drain valve to allow oil to drain from the engine.
MAINTENANCE WOODS AIR CLEANER Clean and replace the air cleaner element as specified in the service chart. Uneven running, lack of power or black exhaust may indicate a dirty air cleaner. 1. Unclamp end cover C and remove existing cleaner element A. 2. Insert new element A and replace cover C. Ensure breathing port B is pointing down and towards the front of the tractor. CLEANING MACHINE WASHING MACHINE Clean the machine after use.
MAINTENANCE WOODS ENGINE COOLING Continued operation with a clogged cooling system will cause severe overheating and can result in engine damage. - Daily: Clean air intake screen V. - Every 100 hours: Clean cooling fins beneath blower housing H with reference to information in the engine manufacturer's manual. SPECIFIC TORQUES B LADE BOLTS 70 FT-LBS (95 Nm ) WHEEL HUB NUTS 150 FT-LBS (203 Nm) ENGINE CRANKSHAFT BOLT 50 FT-LBS (68 Nm ) TRANSAXLE PULLEY NUT 28.3 - 41.
MAINTENANCE WOODS TRANSAXLES Inattention to proper safety, operation, or maintenance procedures could result in personal injury, or damage to the equipment. Schiller Grounds Care, Inc. recommends returning the machine to your authorized Schiller Grounds Care, Inc. dealer for service or repair. Perform transaxle maintenance with the engine off, spark plug wires disconnected and PTO disengaged. TRANSAXLE FLUID CHANGE Change the transaxle fluid every 200 hours of operation.
MAINTENANCE WOODS BLADE REMOVAL BLADE Balance Follow these instructions to prevent injury during blade removal: 1. Loosen with a box wrench or a socket and long breaker bar. To gain additional leverage, slip a long pipe or thick-walled tube over breaker bar or wrench. 2. Insert wood block A as shown, with grain perpendicular to blade, to prevent blade from turning when loosening. 3. Wear thickly padded gloves. Keep hands clear of blade path. Blades may rotate when bolt releases.
ADJUSTMENTS WOODS DECK LEVELING 1. Park the machine on a smooth, level surface. Raise the deck to the transport position. 2. Lower the deck onto a set of equal height blocks under the rear corners of the deck. Place another set of blocks under the front of the deck so that the deck top is pitched forward 1/8". NOTE: The front and rear of the deck are at different heights. 3. Measure the height of the blade cutting edge above the ground. Remove pin B and set the height of cut lever E to that height 4.
ADJUSTMENTS WOODS PARKING Brake FOR 36", 42", 48", AND 52" MODELS NOTE: There are 2 brakes, 1 on each transaxle. The parking brake should keep the machine from moving. To check the parking brake, park the machine on a level surface, open the bypass valves and set the parking brake to ON. Attempt to move the machine forward and backward by pushing it. If the machine moves, adjust the parking brake linkage as follows: 1. Move the machine to a flat horizontal surface. 2. Grip the flats on the brake rod A.
ADJUSTMENTS WOODS PARKING Brake FOR 61" MODELS NOTE: There are 2 brakes, 1 on each transaxle. The parking brake should keep the machine from moving. To check the parking brake, park the machine on a level surface, open the bypass valves and set the parking brake to ON. Attempt to move the machine forward and backward by pushing it. If the machine moves, adjust the parking brake linkage as follows: 1. Move the machine to a flat horizontal surface. 2. Grip the flats on the brake rod A.
ADJUSTMENTS WOODS HydrostatIC TRANSAXLE adjustmentS A turnbuckle style hydro stat neutral adjustment is provided. Neutral: 1. Support the machine with the rear wheels off the ground. Use jack stands or equivalent support. Do not rely only on mechanical or hydraulic jacks. 2. Move the traction levers out into the neutral lock position and raise the seat. 3. Disconnect the seat switch wire and temporarily connect the two terminals with jumper wire J as shown. 4. Start the engine and run at low speed. 5.
ADJUSTMENTS WOODS ARM REST HEIGHT ADJUSTMENTS 1. Remove acorn nuts 1, plastic washers 2, arm rest 3 and second set of plastic washers 4. C C B B A A 2. Adjust carriage bolts 5 to desired height A, B, or C by pushingg on the carriage bolts 5 until they are free from the locking slot, adjusting them to the desired height and then pulling the carriage bolts 5 into the desired locking slot A, B, or C. Bolts must be placed into slots a like heights or arm rest will not fit. 3.
BELT REPLACEMENT WOODS NOTE: Always use Woods replacement belts, not general purpose belts. Woods belts are specially designed for use on this mower and will normally last longer. Cutterdeck belt 1. Remove floorplate. 2. Set the cutterdeck in a middle height-of-cut position. 3. Use a 3/8" ratchet and extension to back tensioning idler off to remove belt from idler. Remove belt from cutterdeck pulleys. NOTE: Use the 3/8" ratchet in the square hole A on the idler. 2 SPINDLE DECK 4.
BELT REPLACEMENT WOODS HYDRO TRANSAXLE DRIVE belt 1. Remove cutterdeck belt (see cutterdeck belt replacement). 2. Disconnect wire I at clutch M. Remove bolts J and remove torque restraint. 3. Using a ratchet with a 9/16" socket, place over nut at location P. Use the ratchet to rotate it enough to remove the transaxle drive belt. 4. Install a new transaxle drive belt by performing these steps in reverse order. 5. Inspect the fans. Replace if worn or damaged. Torque transaxle pulley nut to 28.3-41.
NOTES WOODS NOTES ________________________________________________ ________________________________________________ ________________________________________________ ________________________________________________ ________________________________________________ ________________________________________________ ________________________________________________ ________________________________________________ ________________________________________________ ________________________________________________ ___
PARTS SECTION WOODS PARTS SECTION 43
FRAME-ENGINE/CLUTCH ASSY WOODS FIGURE 1 KAW ENGINE ONLY B & S ENGINE ONLY 10 16 15 17 1 16 JUMPER HARNESS 27 26 3 13 27 21 24 28 22 23 4 29 2 11 18 8 31 5 32 19 14 30 7 12 9 20 25 44 6 10
FRAME-ENGINE/CLUTCH ASSY WOODS ITM PART NO. 1 2 FIGURE 1 DESCRIPTION QTY 4164364 ENGINE-18HP KAW 4164365 ENGINE-20HP KAW 38666.W FILTER-FUEL 4164537 FILTER-OIL 4164329 FILTER-AIR (USED ON MODELS 9CZ2048K) 1 1 4164366 ENGINE-22HP KAW 4164367 ENGINE-24HP KAW 38666.W FILTER-FUEL 4164630 FILTER-AIR 4164631 FILTER-SAFETY 4164537 FILTER-OIL (USED ON MODELS CZ2252K & CZ2461K) 1 1 4163987 ENGINE-23HP B&S 38666.
TRANSAXLE ASSY WOODS FIGURE 2 42 46
TRANSAXLE ASSY WOODS ITM PART NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 FIGURE 2 DESCRIPTION QTY 4164049 S-FRAME W/LABELS 1 4162973 SHAFT-PULLARM MOUNT 1 4163957.7 WLDMT-PULL ARM 2 4163819 ARM-CONTROL 2 4156464 AXLE-LH 1 (INCLUDES ITEMS 4, 25, 26, 27, 32, 39 & 40) (USED ON 36", 48" AND 52" DECKS ONLY) 64163-29 WASHER 2 64123-68 BOLT-HEX 5/16-18X1 2 64025-02 NUT-HEX 5/16-18 2 64270-01 BOLT-MET, HEX M10-1.5x30 1 64123-54 BOLT, 5/16-18X3/4 HEX 2 64163-55 WASHER .328X.
FUEL TANK/BUMPER & CONTROL PANEL WOODS FIGURE 3 8 34 6 19 12 7 14 5 11 10 22 9 13 35 2 30 3 16 17 15 29 16 17 30 32 28 15 26 33 24 25 31 18 / 27 23 4 21 21 18 48
FUEL TANK/BUMPER & CONTROL PANEL WOODS FIGURE 3 ITM PART NO. DESCRIPTION QTY 1 4164049 S-FRAME W/LABS 1 2 4142840-3 TANK-FUEL RH 1 3 4142841-3 TANK-FUEL LH 1 4 4163041.7 BUMPER 1 (USED ON 36", 42", 48" AND 52" DECKS) 4164221.7 BUMPER 1 (USED ON 61" DECKS ONLY) 5 4164526 S-CONTROL PANEL 6 128010-03 S-COVERED KEY 7 128010-01 S-KEY SWITCH NUT 5/8-32 8 2721505 SWITCH-PTO 9 4130320 CAP-FUEL TANK 10 2188178 SWITCH-RETAINER 11 128010.
FUEL VALVE & COVER PLATE FIGURE 4 1 50 WOODS
FUEL VALVE & COVER PLATE WOODS ITM PART NO. 1 2 3 4 5 6 7 8 9 10 11 FIGURE 4 DESCRIPTION QTY 4164049 S-FRAME W/LABS 4142840-1 TANK-FUEL RH 4142841-1 TANK-FUEL LH 64197-001 BLT-TDFM 5/16-18X3/4 4164803.7 COVER-FRAME, REAR 88042N HOSE CLAMP 4162977-009 HOSE-1/4 FUEL LINE 24" 2188161 VALVE-TANK SELECTOR 4130320 CAP-FUEL TANK 4132325 GROMMET-FUEL TANK 4144213 TUBE-FUEL FEED ITM PART NO.
DECK LIFT ASSEMBLY WOODS FIGURE 5 28 30 1 32 9 25 10 16 8 34 24 10 20 22 33 21 29 27 19 16 21 11 6 19 11 7 11 31 14 2 15 5 14 14 18 26 23 4 14 6 3 16 17 2 13 15 14 14 12 12 11 11 CUTTERDECK 52 17 9
DECK LIFT ASSEMBLY WOODS ITM PART NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 4164049 64205-060 4164565.7 4163894.7 4109960 64221-02 4163891.7 2188143 64123-50 85010N 64229-03 2182356.7 64205-029 64246-04 2188127 64163-65 64221-04 4143575.7 2183071-03 4163893.7 64168-2 64188-53 4139785 2720544 64123-67 4126611 4162904.7 64163-31 64175-05 64123-82 4159060 2720743 4159284 64163-29 64018-3 FIGURE 5 DESCRIPTION QTY S-FRAME W/LABS BOLT-MET M12-1.
CASTER ASSEMBLY WOODS FIGURE 6 19 20 54
CASTER ASSEMBLY WOODS ITM PART NO. 1 2 3 4 5 6 7 8 9 FIGURE 6 DESCRIPTION QTY ITM PART NO. DESCRIPTION QTY 4164049 S-FRAME W/LABS 1 4162986 DUST COVER 2 85010N ZERK-1/4-28 2 64025-20 NUT-HEX 3/4-16 SLOT U 2 64163-26 WASHER 2 48043-03C CUP-OUTER BEARING 4 48043-04C CONE-OUTER BEARING 4 48480.W SEAL 2 4143675.7 WLDMT-CASTER 2 (USED ON 36", 42", 48" AND 52" DECKS ONLY) 2721306.
KICKPLATE/SEAT ASSEMBLY WOODS FIGURE 7 2 4 6 5 13 8 5 3 12 24 20 18 23 19 22 8 9 7 1 11 12 9 12 10 17 21 56 16 14 15
KICKPLATE/SEAT ASSEMBLY WOODS ITM PART NO. FIGURE 7 DESCRIPTION QTY 1 2 4164049 4163703 *4163703-01 *4163703-02 *4163703-03 *4163703-04 *4163703-05 S-FRAME W/LABS, SEAT ASSY. SEAT BACK SEAT BOTTOM ARM REST PAD LH ARM MOUNTING BRKT RH ARM MOUNTING BRKT 1 1 1 1 2 1 1 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 4163281.7 4124009 64268-02 33138-09 64144-30 4143354 64141-6 2722325 148082-20 64197-015 2188154 64123-16 64229-03 4164549.
STEERING FIGURE 8 58 WOODS
STEERING WOODS ITM PART NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 4144705 4156297.7 4156295 * 4156294 FIGURE 8 DESCRIPTION QTY GRIP-HANDLE LEVER-TRACTION CNTRL WLDMT-CONTROL BAR, RH WLDMT-CONTROL BAR, LH 2 2 1 1 4143673.7 WLDMT-CONTROL BOX RH 4143674.7 WLDMT-CONTROL BOX LH 108208.W SWITCH DBL POLE 64197-015 BLT-TDFM 10-32X1/2 TORX 4127142 BSHG-CONTROL ARM 64221-03 E-RING 19MM/.
PARKING BRAKE WOODS FIGURE 9 2 17 60
PARKING BRAKE WOODS ITM PART NO. FIGURE 9 DESCRIPTION QTY 1 2 4164049 S-FRAME W/LABST 4156464 TRANSAXLE, RH (USED ON 36", 42", 48", AND 52" ONLY) 1 1 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 64197-015 64168-2 4148697 4146187 64221-03 2188155 4163060.7 64163-34 64006-01 64123-89 2188156 4148698.7 2720977 64229-01 4163772 2 2 2 1 1 1 1 1 1 1 1 2 2 2 1 BLT-TDFM 10-32X1/2 TORX COTTER-HAIRPIN.08X1.19 ROD-BYPASS CONTROL BEARING-FLANGE E-RING 19MM/.
WIRE HARNESS WOODS FIGURE 10 1 2 20 2.0 EXP 15 3 11 ELECTRIC CLUTCH 4 STARTER GROUND 17 YB 16 B 14 GA 12.0 EXP 5.
WIRE HARNESS WOODS ITM PART NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 FIGURE 10 DESCRIPTION QTY 4154880 HARNESS-MAIN WIRE 148082-20 FUSE 20 AMP 30-419 CABLE-BATT 4 GA BLK 29" 4124009 SWITCH-SEAT NO 4136792 METER-HOUR 30-180 CABLE-BATT 4 GA RED 29" (USED ON 22HP, 23HP, AND 24HP ONLY) 1 2 1 1 1 1 2722227-02 CABLE-BATTERY W/COND (USED ON 18HP AND 20HP ONLY) 1 128010.
36" SIDE DISCHARGE WOODS FIGURE 11 15 16 17 5 36 15 14 10 16 9 4 5 11 24 10 25 6 12 8 6 4 27 28 29 32 18 36 14 26 13 7 30 43 19 38 42 17 42 43 46 44 1 44 31 21 21 41 21 45 21 23 2 20 21 37 64 39 34 33 37 31 37 40 16 37 35 22 TORQUE TO 70 FT-LBS 3
36" SIDE DISCHARGE WOODS ITM PART NO. FIGURE 11 DESCRIPTION QTY 1 2 3 4 5 6 7 4152858 S-36 DECK W/LABELS 4147115 CHUTE-RUBBER 112111-02KT2 BLADE 18.00 OFFST HLFT 4115850 S-ASSY SPINDLE OUTER 4144947 PULLEY-SPINDLE 128169 PULLEY, IDLER 5.
48" SIDE DISCHARGE WOODS FIGURE 12 57 66
48" SIDE DISCHARGE WOODS ITM PART NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 FIGURE 12 DESCRIPTION QTY 4146864 S-48 DECK W/LABELS 4146596.25 GUARD-LH 48" DECK 4146595.25 GUARD-RH 48" DECK 4147115 CHUTE-RUBBER 64123-50 BOLT-HEX 3/8-16X1 64018-11 BOLT-CRG 1/2-13X3LG 64229-03 LOCKNUT-NYLON 3/8-16 64205-029 BLT-MET M12X1.75X40 64246-04 NUT-WHIZ M12-1.75 2188127 CHAIN-6.35 (.250) 5 LINKS 4144947 PULLEY-SPINDLE 112111-01KT BLADE 16.25 OFFST HLFT 64262-012 BLT-FLG HD 3/8-16 X 1-1/4 64209-03 SPRING WASHER.
52" SIDE DISCHARGE FIGURE 13 68 WOODS
52" SIDE DISCHARGE WOODS ITM PART NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 FIGURE 13 DESCRIPTION QTY 4153817 S-52 DECK W/LABELS 4143552.25 GUARD-LH 52" DECK 4143553.25 GUARD-RH 52" DECK 4147115 CHUTE-RUBBER ASSY 64123-50 BOLT-HEX 3/8-16X1 64018-11 BOLT-CRG 1/2-13X3LG 64229-03 LOCKNUT-NYLON 3/8-16 64205-029 BLT-MET M12X1.75X40 64246-04 NUT-WHIZ M12-1.75 2188127 CHAIN-6.35 (.250) 5 LINKS 4144947 PULLEY-SPINDLE 112111-02 BLADE 18.
61" SIDE DISCHARGE WOODS FIGURE 14 40 19 18 11 70 27 55 41 66 17 25 15 54 38 30 29 4 57 58 62 44 21 11 34 57 59 6 3 38 39 35 43 53 7 65 20 45 53 7 45 35 35 37 69 45 16 47 40 53 47 47 9 13 35 35 56 5 61 46 46 49 53 42 48 53 53 48 53 7 12 TORQUE TO 70 FT.
61" SIDE DISCHARGE WOODS ITM PART NO. FIGURE 14 DESCRIPTION QTY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 4164130 S-61" DECK 4163809.25 BELT COVER RH 4163808.25 BELT COVER LH 38524.W KNOB-4 PRONG 3/8-16 4147399 CHUTE-RUBBER ASSY 64158-08 EYE BOLT 64229-03 LOCKNUT NYLON 3/8-16 64123-31 BLT-HEX 1/2-13X3 2721512 ROLLER-5X2.75 CENTERED 548138 BRG NDL.88 1.12 1.00 OPEN END 128169 PULLEY IDLER 5.50 112111-03KT BLADE 21.
BELTS-CUTTERDECK WOODS FIGURE 15 5 2 3 4 72
BELTS-CUTTERDECK WOODS ITM PART NO. 1 2 3 4 5 4144212 4143733 4147095 4163569 4147716 FIGURE 15 DESCRIPTION QTY BELT-36" CUTTERDECK BELT-52" CUTTERDECK BELT-48" CUTTERDECK BELT-61" CUTTERDECK BELT-42" CUTTERDECK ITM PART NO.
DECALS-POWERUNIT WOODS FIGURE 16 5 (UNDER SEAT) 16 4 7 2 6 9 8 1 18 18 4 10 14 17 12 11 74 13 3 (UNDER FOOTPLATE)
DECALS-POWERUNIT WOODS ITM PART NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 4144768 2000570 4164525 4152340 2000590 2000701 2000700 4126804 4147617 4164279 4164269 2720743 2000577 4126611 4146936 4133980 4152003 4164835 4164831 4164832 4164833 4164834 FIGURE 16 DESCRIPTION QTY LABEL-CONTROL PANEL LABEL-WARN FUEL PICT.
LIMITED WARRANTY (Mow’n Machine Zero-Turn Mowers and Woods Boundary Utility Vehicles) TM TM Please Enter Information Below and Save For Future Reference.
LIMITED WARRANTY (Mow’n Machine Zero-Turn Mower and Woods Boundary Utility Vehicle Replacement Parts) TM TM Woods Equipment Company (“WOODS”) warrants replacement parts for Mow’n Machine zero-turn mowers and attachments and Woods Boundary utility vehicles, accessories and attachments to be free from defect in material and workmanship for a period of ninety (90) days from the date of delivery of the product to the original purchaser.
Woods Equipment Company 2606 South Illinois Route 2 Post Office Box 1000 Oregon, Illinois 61061 800-319-6637 tel 800-399-6637 fax www.WoodsEquipment.com ©2008 Woods Equipment Company. All rights reserved. WOODS, the Woods logo, and “Tested. Proven. Unbeatable.” are trademarks of Woods Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual are the property of their respective companies or mark holders.
