Rev. 12/1/2006 MAN0118 FSW6000F FSW6000T Tested. Proven. Unbeatable.
TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Woods® dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual are completed before releasing equipment to the owner. The dealer must complete the Product Registration included with the Operator’s Manual. The customer must sign the registration which certifies that all Dealer Check List items have been completed.
TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . INSIDE FRONT COVER GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SAFETY DECALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! ! LEA EL INSTRUCTIVO! Si no lee Ingles, pida ayuda a alguien que si lo lea para que le traduzca las medidas de seguridad. Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to provide safe equipment can be wiped out by an operator’s single careless act.
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Look down and to the rear and make sure area is clear before operating in reverse. Do not operate or transport on steep slopes. Do not stop, start, or change directions suddenly on slopes. Use extreme care and reduce ground speed on slopes and rough terrain. Watch for hidden hazards on the terrain during operation. Stop power unit and equipment immediately upon striking an obstruction.
SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! DANGER DO NOT OPERATE - PUT SHIELD ON MODEL NO. 18869 SHIELD MISSING SERIAL NO. Woods Equipment Company Oregon, Illinois, U.S.A. 4 - PN 18869 BE CAREFUL! 1 - SERIAL NUMPER PLATE Use a clean, damp cloth to clean safety decals.
SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! 5 - PN 72803 2 - PN 18864 CAUTION DANGER PINCH POINT AVOID INJURY FROM FRAME PIVOT AND STOPS ROTATING DRIVELINE D KEEP HANDS AND FEET AWAY.
OPERATION Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to provide safe equipment can be wiped out by an operator’s single careless act. In addition to the design and configuration of equipment, hazard control and accident prevention are dependent upon the awareness, concern, judgement, and proper training of personnel involved in the operation, transport, maintenance, and storage of equipment.
Operate tractor engine at half throttle when de-thatching grass or sweeping dirt. Avoid sudden starts and stops when traveling up and down hill. Never sweep or back up steep hills. When de-thatching grass, stop tractor, disengage PTO, turn off key and check for grass wrap around PTO shaft and universal shaft every 30 minutes of operation. Move very slowly when turning or operating on slopes to reduce the possibility of unit tipping or loss of control. Use the gauge wheels only when de-thatching grass.
SERVICE A In addition to these lubrication points, lightly oil all roller chains periodically. CAUTION Check the oil level in gearboxes periodically. Maintain oil level to the bottom of fill plug hole. Use SAE 90W oil. Always wear relatively tight and belted clothing to avoid getting caught in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate.
ASSEMBLY DEALER SET-UP INSTRUCTIONS Assembly of this sweeper is the responsibility of the WOODS dealer. It should be delivered to the owner completely assembled, lubricated, and adjusted for normal cutting conditions. FIXED ANGLE MOUNT KIT INSTALLATION (Figure 2) Mark Sweeper input driveshaft at 6-1/2 inches from the center cross. Loosen the set screw retaining the rectangular shaft and remove it from the U-joint. Cut shaft to proper length and reinstall shaft and secure with set screws.
20 8--1/4 5 10 TRIM INPUT SHAFT 8 24 DRILL .343 (11/32) DIA HOLES IN SWEEPSTER SHIELD 21 9 7 23 22 6 24 4 2 22 CD4647A 11 3 1 1. Broom mount 7. 2-1/2" Clamp 21. 5/16" NC Flanged hex lock nut 2. 12V Actuator 8. Extension spring 22. 1/2 NC x 2-1/2 Hex head cap screw 3. Universal half sheet 9. Upper actuator mount 23. 1/2 NC x 3 Hex head cap screw 4. Universal half sleeve 10. Caster wheel assembly right 24. 1/2 NC Hex locknut 5. Power shaft shield 11. Caster wheel assembly left 6.
ATTACHING SWEEPER TO TRACTOR (Figure 4) Replace existing step on 2-way angle mount of tractor with shorter step supplied with sweeper. Remove cotter pin on end of step rod and slide out. Install shorter step and replace rod and cotter pin. Keep existing step for use with mower decks if desired. Attach sweeper mount (2) to the holes in tractor mounting bracket (1) that allow the broom mount assembly to set in a level position.
7 PURPLE IGNITION MALE SPADE CONNECTOR 5 FEMALE SPADE CONNECTOR MALE SPADE CONNECTOR 7.5 AMP FUSE BLACK BLACK 5 WAY FEMALE CONNECTOR TO RELAY. MOUNT RELAY TO SEAT HINGE CENTER MOUNTING BOLT.
DEALER CHECK LISTS PRE-DELIVERY CHECK LIST DELIVERY CHECK LIST (Dealer Responsibility) (Dealer Responsibility) ___ Inspect the Mow'n Machine and attachments thoroughly after assembly to be certain it is set up properly before delivering it to the customer. ___ Point out safety features of cutter. Explain the importance and meaning of all safety decals and the potential hazards when not followed. ___ The following check lists are a reminder of points to inspect.
2-WAY ANGLE SWEEPER ASSEMBLY 57 25 28 32 32 CD4646A 31 30 58 51 29 27 3 26 24 45 60 6 50 21 18 17 8 8 36 48 37 38 9 33 38 2 56 46 38 61 15 54 34 37 5 9 4 8 1 47 48 4 9 11 13 39 9 20 63 10 8 44 55 7 3 43 62 22 13 12 52 53 14 23 15 59 30 10 35 41 42 41 14 Parts 32 40 64 -- DECAL SET 17 18 16 MAN0118 (Rev.
2-WAY ANGLE SWEEPER ASSEMBLY REF PART DESCRIPTION REF PART DESCRIPTION - 73967 Sweepster® mounting kit 34 35197 Spring, complete .89 x .12 x 1.0 - 71965 Sweepster® broom head 35 72403 Pin, bent .5 x 1.
FIXED ANGLE SWEEPER MOUNT KIT ASSEMBLY 6--1/2 41 -- DECAL SET TRIM INPUT SHAFT 31 17 16 3 15 4 36 19 2 30 33 40 CD4649A 35 39 5 20 14 37 MANUAL PARTS.
2-WAY ANGLE SWEEPER WIRE DIAGRAM 7 PURPLE IGNITION MALE SPADE CONNECTOR 5 FEMALE SPADE CONNECTOR MALE SPADE CONNECTOR 7.5 AMP FUSE BLACK BLACK 5 WAY FEMALE CONNECTOR TO RELAY. MOUNT RELAY TO SEAT HINGE CENTER MOUNTING BOLT.
BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly.
BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. SAE Bolt Thread Sizes 5/16 3/8 IN MM 1/2 5/8 3/4 7/8 1 2 3 4 5 6 7 25 50 75 100 125 150 175 Metric Bolt Thread Sizes 8MM 10MM 12MM 14MM 16MM 18MM ABBREVIATIONS AG ............................................................. Agriculture NC .................................................... National Coarse ATF...............................
LIMITED WARRANTY (Mow’n Machine Zero-Turn Mower and Woods Boundary Utility Vehicle Replacement Parts) TM TM Woods Equipment Company (“WOODS”) warrants replacement parts for Mow’n Machine zero-turn mowers and attachments and Woods Boundary utility vehicles, accessories and attachments to be free from defect in material and workmanship for a period of ninety (90) days from the date of delivery of the product to the original purchaser.
LIMITED WARRANTY (Mow’n Machine Zero-Turn Mowers and Woods Boundary Utility Vehicles) TM TM Please Enter Information Below and Save For Future Reference.
MAN0118 Woods Equipment Company 2606 South Illinois Route 2 Post Office Box 1000 Oregon, Illinois 61061 815-732-2141 tel 815-732-7580 fax www.WoodsEquipment.com © 2001 WEC Company, d/b/a Woods Equipment Company. All rights reserved. WOODS, the Woods logo, and "Tested. Proven. Unbeatable." are trademarks of Woods Equipment Company.
