Company Yard Vacuum User Manual

ManualsBrandsWoods Equipment ManualsYard VacuumGILL STR48S-2

OPER ATOR'S MANUAL

Super Turf Renovator

& Seedbox

MAN0101

Rev. 3/09/2010

Tested. Proven. Unbeatable.

STR48S-2

STR60S-2

STR72S-2

Summary of content (28 pages)

PAGE 1
Rev. 3/09/2010 MAN0101 STR48S-2 STR60S-2 STR72S-2 Tested. Proven. Unbeatable.
PAGE 2
TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Woods® dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual are completed before releasing equipment to the owner. The dealer must complete the online Product Registration form at the Woods Dealer Website which certifies that all Dealer Check List items have been completed.
PAGE 3
TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 SAFETY DECALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 4
SPECIFICATIONS Super Turf Renovator STR48S STR60S STR72S Working Width 47" 59" 71" Overall Width 58" 70" 82" 1/2" x 1-3/4" 1/2" x 1-3/4" 1/2" x 1-3/4" Six 1" Six 1" Six 1" Roller Pins Bearing (Self-Aligning) Front Roller Positions Adjustable for Increased Agitation Roller Diameter: Front & Rear 8" 8" 8" Cat. I Cat. I Cat. I 65 HP Max. 65 HP Max. 65 HP Max. STR48: 565 lbs. STR60: 710 lbs. STR72: 855 lbs. Weight w/Seedbox STR48S: 820 lbs. STR60S: 920 lbs. STR72S: 1050 lbs.
PAGE 5
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to provide safe equipment can be wiped out by an operator’s single careless act. In addition to the design and configuration of equipment, hazard control and accident prevention are dependent upon the awareness, concern, judgement, and proper training of personnel involved in the operation, transport, maintenance, and storage of equipment.
PAGE 6
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! (Safety Rules continued from previous page) Watch for hidden hazards on the terrain during operation. Stop power unit and equipment immediately upon striking an obstruction. Turn off engine, remove key, inspect, and repair any damage before resuming operation.
PAGE 7
SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! MODEL NO. SERIAL NO. Woods Equipment Company Oregon, Illinois, U.S.A. 3 - Serial Number Plate 6 - PN 20106 Red Reflector 9 - PN 24611 Slow Moving Vehicle 4 - PN 15502 WARNING ROTATING COMPONENTS 5 - PN 18868 Do not operate without cover in place. Look and listen for rotation. Do not open cover until all components have stopped.
PAGE 8
SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! (Safety Decals continued from previous page) WARNING FALLING OFF CAN RESULT IN BEING RUN OVER. Tractor must be equipped with ROPS (or ROPS CAB) and seat belt. Keep foldable ROPS systems in “locked up” position at all times. Buckle Up! Keep seat belt securely fastened. Allow no riders. RAISED IMPLEMENT CAN DROP AND CRUSH.
PAGE 9
OPERATION The operator is responsible for the safe operation of this renovator. The operator must be properly trained. Operators should be familiar with the equipment, the tractor, and all safety practices before starting operation. Read the safety rules and safety decals on page 5 through page 8. Recommended tractor ground speed is from 2 to 5 mph. WARNING Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt securely fastened.
PAGE 10
adjusted to deliver the desired down pressure and roller action and achieve the desired seedbed appearance. 1. Attach the tractor’s lower lift arms to the renovator and secure with mounting pins (11) and klik pins. See Figure 4. When the situation permits, making a second pass 90degrees to the first is an effective way for the roller pins to penetrate areas where uneven soil conditions exist.
PAGE 11
Adjust Front Roller Angle 1. Position tractor and renovator on a level surface. 6. Install lock assembly (5), lock pin (15), and klik pin (21) to secure front roller into position. 7. Reverse this procedure to move front roller back into normal position. 2. Raise renovator slightly off the ground. 3. Stop engine and set parking brake. 4. Remove klik pin (21), lock pin (15), and lock assembly (5) from front of renovator. See Figure 6.
PAGE 12
Operating Tips Pre-Operation Check List (OWNER’S RESPONSIBILITY) IMPORTANT ■ Before closing down the cup (reducing rates), the operator should make certain that the cups are not full of seed. If cups are full of seed (especially small, round, hard seed), it may be necessary to cover the meter holes and run seeder a short distance to reduce level of seeds in meter. Failure to do so could result in damage to seed cup. 1. Do not allow dirt to build up on the roller sprockets.
PAGE 13
MAN0101 (Rev.
PAGE 14
OWNER SERVICE The information in this section is written for operators who possess basic mechanical skills. If you need help, your dealer has trained service technicians available. For your protection, read and follow the safety information in this manual. WARNING NEVER GO UNDERNEATH EQUIPMENT. Never place any part of the body underneath equipment or between moveable parts even when the engine has been turned off.
PAGE 15
ASSEMBLY DEALER SET-UP INSTRUCTIONS Assembly of this equipment is the responsibility of the Woods dealer. It should be delivered to the owner completely assembled, lubricated, and adjusted for normal operating conditions. 12 15 In most cases the Super Turf Renovator is shipped completely assembled from the factory. The seed box is an option that can be added to the Super Turf Renovator at a later time if desired. Install Seedbox 1. Place seedbox on top of renovator mounting saddles. 2.
PAGE 16
5. Slide idler bracket assembly forward to apply tension to the horizontal drive chain. 6. Slide idler and spring bracket down to apply tension to the vertical drive chain. NOTE: Do not over tighten. Allow some slack in chain. Idler Bracket Assembly 7. Adjust opposite side of roller to level. 30 31 A 30 31 Idler Bracket Assembly DP14 Figure 14. Idler Bracket Assembly Installed Install Roller Chains 1.
PAGE 17
PARTS INDEX Super Turf Renovator & Seedbox Kit STR48S-2 STR60S-2 STR72S-2 Main Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 - 19 Seedbox Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 - 21 Drive Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Quick Hitch Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 MAN0101 (Rev.
PAGE 18
STR48S-2, STR60S-2 & STR72S-2 MAIN ASSEMBLY 18 Parts MAN0101 (Rev.
PAGE 19
STR48S-2, STR60S-2 & STR72S-2 MAIN ASSEMBLY PARTS LIST REF 1 STR 48-2 ………… STR 60-2 ………… STR72-2 ………… QTY DESCRIPTION 1 STR Frame 2 1000778 1000778 1000778 1 Rear roller arm, right 3 1000779 1000779 1000779 1 Rear roller arm, left 4 D2213 D2213 D2213 4 Bushing, 0.88 ID 5 1002912 1001716 1001716 1 Lock assembly 6 1001984 1001984 1001984 2 Spring pin, .75 x 11.
PAGE 20
STR48-2, STR60S-2 & STR72S-2 SEEDBOX ASSEMBLY 20 Parts MAN0101 (Rev.
PAGE 21
STR48-2, STR60S-2 & STR72S-2 SEEDBOX PARTS LIST REF 1 2 3 4 5 STR 48-2 1000001 100001348 ………… 1000766 100293248 STR 60-2 1000001 100001360 ………… 1000766 100293260 STR72-2 1000001 100001372 ………… 1000766 100293272 QTY 1 1 1 1 1 6 100293348 100293360 100293372 1 7 8 9 10 11 12 13 14 15 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 47 48 49 50 51 1000782 1000783 1000784 1000787 1000790 (8) 1001705 1001721 100172248 46490 (8) 1001986 1001987 1001988 (6) 1001993 100
PAGE 22
STR48-2, STR60S-2 & STR72S-2 DRIVE ASSEMBLY REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 STR 48-2 ………… ………… 1001710 7832* 57817* 230 1000791 1001983 1002930 1002931 35139* 1257* SU613 12296* 56722 1001709 66840 5607* 19025* FA419 100293648 1002939 1001975 1001994* 12169* 14350* 1002934 1002935 1002959 STR 60-2 ………… ………… 1001710 7832* 57817* 230 1000791 1001983 1002930 1002931 35139* 1257* SU613 12296* 56722 1001709 66840 5607* 19025* FA419 100293660 1002939 1001975 10
PAGE 23
STR48-2, STR60S-2 & STR72S-2 QUICK HITCH KIT REF PART 1 2 MAN0101 (Rev.
PAGE 24
BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly.
PAGE 25
BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. SAE Bolt Thread Sizes 5/16 3/8 1/2 IN MM 5/8 3/4 7/8 1 2 3 4 5 6 7 25 50 75 100 125 150 175 Metric Bolt Thread Sizes 8MM 10MM 12MM 14MM 16MM 18MM ABBREVIATIONS AG ............................................................. Agriculture ATF...............................Automatic Transmission Fluid BSPP ..........................
PAGE 26
WARRANTY (Replacement Parts For All Models Except Mow’n MachineTM Zero-Turn Mowers and Woods BoundaryTM Utility Vehicles) Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship for a period of ninety (90) days from the date of delivery of the product to the original purchaser with the exception of V-belts, which will be free of defect in material and workmanship for a period of 12 months.
PAGE 27
WARRANTY (All Models Except Mow’n MachineTM Zero-Turn Mowers and Woods BoundaryTM Utility Vehicles) Please Enter Information Below and Save for Future Reference. Date Purchased: ____________________________ From (Dealer): __________________________________________ Model Number: ____________________________ Serial Number: __________________________________________ Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship.
PAGE 28
PART NO. MAN0101 © 2001 Woods Equipment Company. All rights reserved. WOODS, the Woods logo, and "Tested. Proven. Unbeatable." are trademarks of Woods Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual are the property of their respective companies or mark holders. Specifications subject to change without notice.