Center Drive S30CD OPERATOR'S MANUAL (11/8/2011) MAN0943 FLAIL SHREDDER
TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Woods® dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual are completed before releasing equipment to the owner. The dealer must complete the online Product Registration form at the Woods Dealer Website which certifies that all Dealer Check List items have been completed.
TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 BALANCE STATEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIFICATIONS Maximum Outside Body Width: . . . . . . . 31ft. - 3in. Cutting Height: . . . . . . . . . . . . . . . . . . . . 3in. - 18in. (7.62 cm to 45.7 cm) Width of Cut:. . . . . . . . . . . . . . . . . . . . . . 30ft Number of Knives: Cups “L” “L” Cut-Off 176 348 4 Recommended Tire Size: . . . . . . . . . . . . 9.5L - 15,6 ply rated Tire Inflation Pressure: . . . . . . . . . . . . . . 25 psi Rotor: Speed . . . . . . . . . . . . . . . . . . . . . 1350 RPM dynamically balanced Drive: PTO . . . . .
IMPORTANT! BALANCE STATEMENT Both of the Woods Center Drive Shredder flail tubes are balanced as rotor assemblies to meet or exceed factory standards before installation. After installation, the shredders are statistically inspected to check balance. These factory efforts allow the shredder to operate smoothly and be free of excessive vibration when delivered to the customer. WARNING wear unevenly. This can reduce their chopping effect and also increase vibration levels.
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to provide safe equipment can be wiped out by an operator’s single careless act. In addition to the design and configuration of equipment, hazard control and accident prevention are dependent upon the awareness, concern, judgement, and proper training of personnel involved in the operation, transport, maintenance and storage of equipment.
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Inspect rubber flaps and swing rod before each use. Replace if damaged or missing. Flaps must pivot and hang freely so there are no gaps. Do not put equipment into service until repaired. Remove accumulated debris from this equipment, power unit, and engine to avoid fire hazard. Make sure all safety decals are installed. Replace if damaged. (See Safety Decals section for location.
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! (Safety Rules continued from previous page) Look down and to the rear and make sure area is clear before operating in reverse. Do not operate or transport on steep slopes. Do not stop, start, or change directions suddenly on slopes. Use extreme care and reduce ground speed on slopes and rough terrain. Watch for hidden hazards on the terrain during operation. Stop power unit and equipment immediately upon striking an obstruction.
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Make sure all safety decals are installed. Replace if damaged. (See Safety Decals section for location.) Leak down or failure of mechanical or hydraulic system can cause equipment to drop. Make sure shields and guards are properly installed and in good condition. Replace if damaged.
SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! 3 - SERIAL NUMBER DECAL 1 - YELLOW REFLECTOR PN 20034004 2 - RED REFLECTOR PN 57123 4 - RED-ORANGE FLUORESCENT MATERIAL PN 20034034 5 - PN 50030977 CAUTION PRECAUCION 1. Read Operator's Manual before starting. 1. Lea el Manual del Operario antes de empezar. 2.
SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! DANGER PELIGRO DANGER PELIGRO ROTATING FLAIL HAZARD ROTATING DRIVELINE HAZARD To prevent serious injury or death from rotating flails: 1. Stop engine, remove ignition key, and wait for moving parts to stop before servicing. 2. Keep hands and feet away from flails when engine is running. 3. Keep other people away. To prevent serious injury or death from rotating driveline: 1.
SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! (Safety Decals continued from previous page) 12 - PN 50530728 11 - PN 50530707 WARNING ADVERTENCIA 14 - PN 50530315 16 - PN 33347 15 - PN 18864 HIGH-PRESSURE FLUID HAZARD To prevent serious injury or death: 1. Relieve pressure on system before repairing, adjusting, or disconnecting. 2. Wear proper hand and eye protection when searching for leaks. Use wood or cardboard instead of hands. 3.
OPERATOR SIGN-OFF RECORD Woods Equipment Company follows the general safety standards specified by the American Society of Agricultural and Biological Engineers (ASABE) and the Occupational Safety and Health Administration (OSHA) for agricultural equipment. Anyone who will be operating and/or maintaining the flail shredder must read and clearly understand all Safety, Operating, and Service & Maintenance information presented in this manual.
OPERATION The Woods Flail Shredder is designed to pick up and shred crop and plant residue left in the field. Rotational power to the flails is provided by the tractor PTO. Be familiar with the flail shredder before starting. The owner is responsible for training operators in the safe operation of the flail shredder. WARNING Safety instructions are important! Read all attachment and power unit manuals; follow all safety rules and safety decal information.
1. Crossmember 2. Rubber belt shield 3. Skid assembly 4. Rubber belt shield 5. Body weldment 6. Flail tube assembly RH 7. Flail tube assembly LH 8. Woods model decal 9. Gearbox 10. Bearing assembly Figure 1. Flail Shredder Principal Components PRE-OPERATION CHECK LIST (OWNER'S RESPONSIBILITY) NOTICE ■ This Pre-Operation Check List is provided for the operator. It is important to follow for both personal safety and maintenance of the flail shredder.
Table 1: Tractor Horsepower (6-8) vs. Unit Width Width Upper Top Link Hole Minimum Horsepower 30’ 180 Top Link Assembly Lower Top Link Pin Lower 3-Point Pin DP11 Figure 3. 3-Point Hitch Attachment NOTICE PTO DRIVELINE LENGTH ■ DP10 Figure 2. Tractor Front Weight 3. 3-Point Hitch The 3-point hitch models require that the tractor be equipped with a Category II or Category III 3-point hitch.
7. Use an abrasive wheel power saw to cut the male end of the shaft. Cut the same amount from both the splined shaft and the safety shield. See Figure 4. Use a file to remove any burrs from the cut end. 2. Clear the area of bystanders, especially children. 3. Provide enough clearance to back the tractor safely into the unit. NOTICE CAUTION ■ Cut only the male end. Never cut the female end. 8. Never cut more than 9 inches from the male end.
FIELD OPERATION Without Quick Hitch Attachment: 10. Back tractor lower 3-point arms between lower mast plates and align with lower 3-point hole. 11. Place 1-3/4 OD spacer through 3-point arm pivot (both sides). 12. Push tractor’s 3-point arm to the inside and slide a 1-7/16 OD spacer between to take up the empty space. Secure with lower 3-point hitch pin assembly, 1-3/4 OD spacer, and 7/16 x 2 klik pin. 13. Repeat steps 5 and 6 for other side. 14.
Stroke Control Spacers CAUTION Always sit in power unit seat when operating controls or starting engine. Securely fasten seat belt, place transmission in neutral, engage brake, and ensure all other controls are disengaged before starting power unit engine. Always comply with all state and local lighting and marking requirements. Always wear relatively tight and belted clothing to avoid getting caught in moving parts.
1. Leave standard flails located between the rows. 2. Remove others and install shorter flails to follow ground contour. Be sure to mount the same size flails on opposite sides of the tube. Measure the row spacing and flail position carefully to minimize ground contact. See page 36 and page 37. mm) above the ground. (See Balance Statement, page 5.) 2. Align the unit with the working area on or between rows on flat farming. 3. Use stroke control spacers on four cylinders to set cutting height. .
STOPPING THE SHREDDER WARNING Before dismounting power unit or performing any service or maintenance, follow these steps: disengage power to equipment, lower the 3-point hitch and all raised components to the ground, operate valve levers to release any hydraulic pressure, set parking brake, stop engine, remove key, and unfasten seat belt. GROUND SPEED Travel speed can vary between 3 and 8 mph (5 and 13 kmph) depending on the bulk of residue and terrain conditions.
5. An end tow hitch is also available as optional equipment for hooking shredder to quick hitch. DP102 DP118 Figure 15. Transport Position Figure 18. End Tow - Quick Hitch 2. Set shredder back on all four wheels using 3-point. Raise all shredder lift cylinders to maximum lift height. Flip transport locks into transport position (see Figure 16). Lower cylinders into transport lock. Make sure all four cylinders have bottomed out. 6.
3. Inspect the flails and rotors for damage or entangled material. Remove entangled material. Repair or replace damaged parts. 4. Inspect all hydraulic hoses, lines, couplers, and fittings. Tighten all loose fittings. Replace any hose that is cut, nicked, abraded, or separating from the crimped end of a fitting. 5. Change gearbox oil. 8. Move to storage area. Select a dry area free of debris. Store in an area away from human activity. 9. Unhook from tractor (see Removing Shredder from Tractor, page 18).
SERVICE & MAINTENANCE WARNING Before dismounting power unit or performing any service or maintenance, follow these steps: disengage power to equipment, lower the 3-point hitch and all raised components to the ground, operate valve levers to release any hydraulic pressure, set parking brake, stop engine, remove key, and unfasten seat belt. Before working underneath, read manual instructions, securely block up, and check stability.
Figure 20. PTO Driveline Lubrication Points A. Daily or 8 hours B. 25 hours C. 40 hours D. Check Daily/Change Annually Figure 21. Lubrication Points Daily or every 8 hours of operation Every 25 hours of operation 1. Lubricate PTO U-joints and over-running clutch. 2. Check gearbox daily or every 8 hours of operation. See Figure 22 for gearbox oil fill location. DP106 Figure 22. Gearbox Oil Fill Location MAN0943 (07/12/2011) 1.
Every 40 hours of operation - Figure 24 2. Repack wheel bearings. See Figure 26. 1. Lubricate rotor drive couplers next to the couplers on underside of unit and inside of flail tube (access through windows on back panel of shredder). 2. Grease the drive hubs with 10 to 20 pumps. You may use extra grease only on drive hubs. DP110 Figure 26. Wheel Bearings 3. Lubricate pivot tube (2 locations each pivot tube). See Figure 27. DP109 Figure 24. Drive Couplers and Hubs Annually DP113 1.
LUBRICATION SERVICE RECORD NOTE: See page 24 through page 27 for details. Copy this page to continue service record.
GEARBOX OIL LEAKAGE ■ Major oil leakage from the gearbox shaft seal 3. Closely monitor gearbox for 10 hours of operation. Check and service oil every 30 minutes or as needed to ensure operation does not occur with oil below the add mark. area is not acceptable and could cause the gearbox to fail due to lack of lubrication and cooling. It is the operator’s responsibility to check the gearbox oil level per the Lubrication Service Table. 4.
Figure 29. Acceptable Oil Leakage GEARBOX DRAIN PLUG DP114 DP16 Figure 30. Drain Plug (Underside of Unit) 7. Re-install and tighten drain plug. 8. Dispose of used oil in an approved container. 9. Add SAE 85W90 gear oil through the dipstick cover. Use the dipstick to check the oil level (Figure 31) and add oil accordingly. 10. Re-install and tighten fill plug. 11. Reconnect PTO driveline and hydraulic lines. 12. Remove blocks or safety stands. Figure 31.
7. Loosen mounting bolts on one wheel assembly. 8. Slide assembly along the frame tube to new position (see Figure 32). 9. Tighten mounting bolts to specified torque level. 5. Loosen and remove the worn knife and its opposite on the other side of the rotor. Discard worn knives and their mounting hardware. 6. Replace with new knives and mounting hardware (see Figure 33). DP13 DP116 Figure 33. Flail Replacement Figure 32. Positioning Wheel Assembly 10. Remove safety stands or blocks.
Factory balanced replacement rotors are available through your local Woods dealer. Contact Woods Technical Service for re-balance options or further details. Follow the procedure below if rotor removal or replacement is required. CAUTION DP117 Figure 34. Front Rubber Shield Flaps 4. Replace damaged flap with new flap and secure with correct hardware. NOTE: Use only genuine Woods parts when replacing flaps. Use a suitable lifting device of sufficient capacity.
LOCKING COLLAR SET SCREW LOCKING COLLAR FS211 PEER SHAFT FOR REMOVAL: TAP WITH A HAMMER AND PUNCH AFTER LOOSENING SET SCREW. FOR INSTALLATION: REVERSE PROCEDURE MAN0506003 Figure 35. Locking Collar NOTE: When re-installing rotors, the gear coupling grease fitting will need to be temporarily removed to allow for air to purge from the coupler assembly during installation. After successful installation, reinstall grease fitting and re-service. 7.
Figure 37. Stub Shaft Assembly Removing the Driveline 2. Press a new leaf spring into each pocket. The ends should touch the bottom of the pockets. 1. Shut off tractor and disengage PTO. 2. Disconnect driveline from PTO shaft. 3. Remove the bolts and clamp that attaches the clutch to the shredder’s input shaft. NOTE: The shaft is heavy. Grasp the clutch firmly with both hands and slide off the input shaft. Rebuilding Overrunning Clutch Disassembly 1. Remove the four bolts that secure the friction pack.
NOTES 34 Service & Maintenance MAN0943 (07/12/2011)
TROUBLESHOOTING The Woods Flail Shredder uses swinging flails to pick up and shred crop residue left in the field. It is a simple and reliable system that requires minimal maintenance. The following table lists problems, causes, and solutions that you may encounter. If you encounter a problem that is difficult to solve even after reading through this table, please call your local Woods dealer. When calling, please have this manual and your unit’s serial number ready.
WORKSHEET FOR CONTOUR FLAIL PATTERNS 36 Contour Flail Patterns MAN0943 (07/12/2011)
WORKSHEET FOR CONTOUR FLAIL PATTERNS 24’ MAN0943 (07/12/2011) Contour Flail Patterns 37
ASSEMBLY DEALER SET-UP INSTRUCTIONS WARNING Do not allow bystanders in the area when operating, attaching, removing, assembling, or servicing equipment. Do not handle knives with bare hands. Careless or improper handling may result in serious injury. NOTICE ■ For units shipped on aft end, the dipstick ship- ping plug must be removed before shredder operation. Replace plug with dipstick in filler tube after shredder has been removed from truck and leveled.
3. Attach crossmember to strut uprights. Tighten all mounting hardware at this time per torque chart, Figure 41. 7. Attach cylinders, fittings, and hoses. See parts section. 8. Connect hoses to tractor and cycle cylinder in and out to remove air from system. Check for leaks at this time. 9. While shredder is setting on skids, retract cylinders fully until cast yokes are high enough to mount wheels. Torque wheel nuts per torque chart. 10. Check tire pressure. Recommended tire pressure is 30 PSI. 11.
ALL UNITS 1. Install PTO driveline by sliding the yoke with the slip clutch over the input shaft (Figure 45). 2. Tighten interlocking clamp bolts to their specified torque of 160 ft lbs. 2. Attach rubber belting and bars to front of shredder using 3/8 NC x 1-1/2 carriage bolts and 3/8 flange lock nuts. NOTE: Use equal number of belting and bars on each side of shredder. 3. Tighten all hardware. RUBBER FLAP INSTALLATION 1. Remove all components from shipping carton.
SAFETY LIGHT INSTALLATION 1. Remove all components from shipping carton. Make sure that all required hardware is included. 2. Attach dual safety lights (Figure 48) to safety light mounting brackets (9) using cap screws (17) and lock nuts (18). NOTE: Make sure that light lenses are in the correct position in relation to direction of equipment travel: amber lenses on the outside, red lenses on the inside facing rear of shredder. 3.
END TOW HITCH INSTALLATION 1. Attach lower end tow hitch mount (4) using carriage bolts (26), and lock nuts (25). 2. Attach tongue lockup bracket (3) using carriage bolts (26), and locknuts (25). 3. Bolt hitch (1) to tow hitch mount brackets (33) using cap screws (27) and locknuts (28). OPTIONAL EQUIPMENT INSTALL CENTER DEFLECTOR Slide deflector (1) between shredder center channel with the point forward. Secure into position using four 1/2 NC x 1-1/4 carriage bolts (2) and flange lock nuts (3). 4.
Do not position jackstands under wheels, axles, or wheel supports. Components can rotate and cause shredder to fall. 2. Consider the overall stability of the blocked unit. Just placing jackstands underneath will not ensure your safety. The working surface must be level and solid to support the weight on the jackstands. Make sure jackstands are stable, both top and bottom. Make sure shredder is approximately level. 3.
31 30 29 DP1 Figure 54. Hose Assembly Figure 53. Motor Assembly Installed Assembly Hoses 1. Attach male quick coupler (17) and adapter (16) to the end of hose (15). Attach tee (12) to the opposite end of hose. 2. Attach male quick coupler (17) and adapter (16) to the end of second hose (15). Attach check valve (14), nipple (13) and tee (12) to the opposite end of hose. 6.
Install Hose Clamps Connect Hoses to Tractor 1. Place hose clamps (36) around hoses (11) and center hoses between center plate. 2. Mark clamp holes in desired location on shedder body and drill two 11/32" holes. 3. Secure hose clamps to shredder using 5/16 NF x 1-1/4 cap screws (20), flat washers (33), lock washers (34) and hex nuts (35). See Figure 56. NOTICE ■ Oil flow to hydraulic motor must not exceed 28 gpm. 1.
DEALER CHECK LISTS PRE-DELIVERY CHECK LIST (DEALER’S RESPONSIBILITY) Inspect the equipment thoroughly after assembly to make sure that it is set up properly before delivering it to the customer. The following check lists are a reminder of points to inspect. Check off each item as it is found satisfactory or after proper adjustment is made. ___ Check that all safety decals are installed and in good condition. Replace if damaged. ___ Properly attach implement to tractor and make all necessary adjustments.
PARTS INDEX FLAIL SHREDDER Center Drive FRAME ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 - 49 FLAIL TUBE ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 STRUT AND CASTER ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . .51 SAFETY LIGHT KIT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 - 53 WEASLER 30K AUTOMATIC CLUTCH . . . . . . . . . . . . . . . . . . . . . . . .
CENTER DRIVE FLAIL SHREDDER FRAME ASSEMBLY 48 Parts MAN0943 (07/12/2011)
CENTER DRIVE FLAIL SHREDDER FRAME ASSEMBLY PARTS LIST REF 1 2 PART NSS ---------- 3 1029365 4 1029372 5 1029554 6 1029554 7 7144 8 1004814 9 29547 10 1012170 11 1010120 12 1013067 13 1003828 14 1013049 15 1030513 16 90315407 17 1012175 18 50030338 19 900109126 20 1013114 21 1019755 22 20020553 23 1016186 24 1016187 25 20030151 26 20030961 27 20030960 28 20030959 29 1020013 30 90039030 31 37431 35 923 QTY 1 - DESCRIPTION 30’ Shredder Body Flail tube asy, right & left (see page 50) 4 Strut upright asy 2
FLAIL TUBE ASSEMBLY REF LEFT PART # RIGHT PART # QTY DESCRIPTION 30’ Flail tube w/knives 30’ HD Cotton tube w/knives 30’ Cup knife tube w/knives Stub shaft, 2-3/16" L-Knife, long 8-1/2", (6 mm) L-Knife, HD cotton (Durafaced) (8 mm) Weld-on clip 3/8 High collar lock washer L- Knife, cut off L- Knife, cut off Drive hub sleeve, outer 3/8 NC x 2-1/2 SHCS 1/2 NC x 2-3/4 Tap bolt, full thread 1/8 NPT Straight grease fitting 1 1 1029355LK 1029354LK 1029355HD 1029354HD 1 1 1 1029355CP 1029354CP 1 2 3 1
STRUT AND CASTER ASSEMBLY REF PART NO QTY DESCRIPTION REF PART NO QTY DESCRIPTION 1 1029554 4 Caster Pivot Assembly 16 20031766 8 Bearing, Caster Pivot 2 1030508 4 Caster Assembly 17 20031219 4 Retainer Pin 3 90509009 4 Dust Cap 18 90001221 4 1/2 NF x 1 HHCS, GR5 4 90006060 4 7/8 NF Slotted Nut 19 90025030 2 3/4 x 6 Hitch Pin 5 90509067 4 7/8 Washer 20 22411 4 3/16 Klik Pin 6 90109067 4 Bearing Cone N/S 90509070 4 Tire, 9.
END TOW AND SAFETY LIGHT ASSEMBLY 52 Parts MAN0943 (07/12/2011)
END TOW ASSEMBLY AND SAFETY LIGHT PART LIST REF PART 1 1019826 2 19407 3 5 QTY DESCRIPTION REF PART QTY 1 Hitch 17 11027 * 1 Tow Chain, 10,000 lbs 18 90001009 * 1029565 1 Tongue Lock-Up 25 11900 * 1019834 1 Light Mount 26 90001751 * 6 90401151 1 Wire Harness 27 90001381 * 7 90507121 12 Adhesive Back Clamp 28 19025 * 8 24611 1 Slow Moving Vehicle Sign 29 9 50520563 2 Dual Safety Light Arm 30 1 Jack, 2000 lbs 33 10 23790 11 90401149 1 Left Dual Lamp 12 90401
REF PART QTY DESCRIPTION PTO Shaft complete 1-3/4 20-spline 30K 3-point with automatic clutch Slide lock repair kit 1.75 ID 1-3/4 20-Spline yoke U-Joint cross & bearing kit 55E Yoke & shaft, 1.69 20-spline, 30.6 long -ORYoke & shaft, 1.69 20-spline, 26.
RUBBER BELTING REF PART QTY 1 2 3 4 1012202 1022647 1029560 1019561 8 8 2 2 DESCRIPTION Rubber belting Belt bar Belt bar Rubber belting MAN0943 (09/07/2011) REF 5 6 PART QTY 64824 * 14350 * * DESCRIPTION 70 3/8 NC x 1-1/2 Carriage bolt 70 3/8 NC flange lock nut Standard hardware, obtain locally Parts 55
RUBBER FLAP REF PART QTY 1 50531089 2 1022659 3 1022660 5 1022655 30 7 7 2 DESCRIPTION REF 5 6 7 8 9 10 Rubber flap (12") Flap bracket, right Flap bracket, left Flap rod (20 ft) PART QTY DESCRIPTION 1029562 2 Flap rod (30’) 1026528 2 Swing flap bar, mast plate (32" all) 1026529 2 Swing flap bar (32", 20 ft, 25 ft, 27 ft) 6697 * 70 3/8 NC x 1 Carriage bolt 14350 * 70 3/8 NC Flange lock nut 90023043 * 4 3/16 x 1-1/2 cotter pin * Standard hardware, obtain locally HYDRAULIC HOSE ASSEMBLY REF 4 20 2
CENTER CUTTER KIT (OPTIONAL) 24 - 50530315 25 - 50530263 WARNING ADVERTENCIA HIGH-PRESSURE FLUID HAZARD To prevent serious injury or death: 1. Relieve pressure on system before repairing, adjusting, or disconnecting. 2. Wear proper hand and eye protection when searching for leaks. Use wood or cardboard instead of hands. 3. Keep all components in good repair. PELIGRO DE FLUIDO BAJO ALTA PRESION Para evitar heridas graves o la muerte: 1.
CENTER CUTTER KIT PARTS LIST REF PART QTY DESCRIPTION 1 1024671 1 Blade hub 2 1016161 1 Motor housing 3 1024674 1 Blade, .31 x 2.50 x 13.
BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly.
BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. SAE Bolt Thread Sizes 5/16 3/8 1/2 IN MM 5/8 3/4 7/8 1 2 3 4 5 6 7 25 50 75 100 125 150 175 Metric Bolt Thread Sizes 8MM 10MM 12MM 14MM 16MM 18MM ABBREVIATIONS AG .............................................................. Agriculture ASABE ....................American Society of Agricultural & Biological Engineers (formerly ASAE) ASAE.......
INDEX Setting Flail Height 20 Setting Operating Height 19 Setting Outer Trailing Wheels 20 Starting the Tractor 20 Stopping the Tractor 21 Turning 21 A ASSEMBLY Dealer Set-Up Instructions 38 Optional Equipment Center Cut Kit Installation 42 Rubber Belting Installation 40 Rubber Flap Installation 40 Safety Light Kit Installation 41 Optional Equipment Rubber Flaps 19 Pre-Operation Check List (Owner’s Responsibility) 15 Preparing for Operation 19 Principal Components 14 Removing Shredder from Tractor 18 Stor
WARRANTY All Models Except Mow’n MachineTM Zero-Turn Mowers Please Enter Information Below and Save for Future Reference. Date Purchased: ____________________________ From (Dealer): __________________________________________ Model Number: ____________________________ Serial Number: __________________________________________ Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship.
WARRANTY (Replacement Parts For All Models Except Mow’n MachineTM Zero-Turn Mowers) Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship for a period of ninety (90) days from the date of delivery of the product to the original purchaser with the exception of V-belts, which will be free of defect in material and workmanship for a period of 12 months.
MAN0943 Woods Equipment Company 2606 South Illinois Route 2 Post Office Box 1000 Oregon, Illinois 61061 815-732-2141 tel 815-732-7580 fax www.WoodsEquipment.com © 1994 Woods Equipment Company. All rights reserved. WOODS, the Woods logo, and "Tested. Proven. Unbeatable." are trademarks of Woods Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual are the property of their respective companies or mark holders.
