(Rev.
TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Woods® dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual are completed before releasing equipment to the owner. The dealer must complete the online Product Registration form at the Woods Dealer Website which certifies that all Dealer Check List items have been completed.
TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 BALANCE STATEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIFICATIONS Maximum Outside Body Width: 20′ . . . . . . . . . . . . . . . . . . 253 in. (6.4 m) 22′ . . . . . . . . . . . . . . . . . . 277 in. (7.0 m) 25′ . . . . . . . . . . . . . . . . . . 309 in. (7.8 m) 27′ . . . . . . . . . . . . . . . . . . 334 in. (8.4 m) 30′ . . . . . . . . . . . . . . . . . . 375 in. (9.5 m) Cutting Height: . . . . . . . . . . . . . . . . . . . . 3 - 18 in. (7.62 cm to 45.7 cm) Width of Cut: 20′ . . . . . . . . . . . . . . . . . . 247 in. (6.2 m) 22′ . . . . . . . . . . . . . .
IMPORTANT! BALANCE STATEMENT Both of the Woods Center Drive Shredder flail tubes are balanced as rotor assemblies to meet or exceed factory standards before installation. After installation, the shredders are statistically inspected to check balance. These factory efforts allow the shredder to operate smoothly and be free of excessive vibration when delivered to the customer. WARNING wear unevenly. This can reduce their chopping effect and also increase vibration levels.
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to provide safe equipment can be wiped out by an operator’s single careless act. In addition to the design and configuration of equipment, hazard control and accident prevention are dependent upon the awareness, concern, judgement, and proper training of personnel involved in the operation, transport, maintenance and storage of equipment.
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Inspect rubber flaps and swing rod before each use. Replace if damaged or missing. Flaps must pivot and hang freely so there are no gaps. Do not put equipment into service until repaired. Always raise unit and install transport locks before transporting. Leak down or failure of mechanical or hydraulic system can cause equipment to drop. Remove accumulated debris from this equipment, power unit, and engine to avoid fire hazard.
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! (Safety Rules continued from previous page) Look down and to the rear and make sure area is clear before operating in reverse. Do not operate or transport on steep slopes. Do not stop, start, or change directions suddenly on slopes. Use extreme care and reduce ground speed on slopes and rough terrain. Watch for hidden hazards on the terrain during operation. Stop power unit and equipment immediately upon striking an obstruction.
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Make sure all safety decals are installed. Replace if damaged. (See Safety Decals section for location.) Leak down or failure of mechanical or hydraulic system can cause equipment to drop. Make sure shields and guards are properly installed and in good condition. Replace if damaged.
SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! 3 - SERIAL NUMBER DECAL 1 - YELLOW REFLECTOR PN 20034004 2 - RED REFLECTOR PN 57123 4 - RED-ORANGE FLUORESCENT MATERIAL PN 20034034 5 - PN 50030977 CAUTION PRECAUCION 1. Read Operator's Manual before starting. 1. Lea el Manual del Operario antes de empezar. 2.
SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! DANGER PELIGRO DANGER PELIGRO ROTATING FLAIL HAZARD ROTATING DRIVELINE HAZARD To prevent serious injury or death from rotating flails: 1. Stop engine, remove ignition key, and wait for moving parts to stop before servicing. 2. Keep hands and feet away from flails when engine is running. 3. Keep other people away. To prevent serious injury or death from rotating driveline: 1.
SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! (Safety Decals continued from previous page) 12 - PN 50530728 11 - PN 50530707 WARNING ADVERTENCIA 14 - PN 50530315 16 - PN 33347 15 - PN 18864 HIGH-PRESSURE FLUID HAZARD To prevent serious injury or death: 1. Relieve pressure on system before repairing, adjusting, or disconnecting. 2. Wear proper hand and eye protection when searching for leaks. Use wood or cardboard instead of hands. 3.
OPERATOR SIGN-OFF RECORD Woods Equipment Company follows the general safety standards specified by the American Society of Agricultural and Biological Engineers (ASABE) and the Occupational Safety and Health Administration (OSHA) for agricultural equipment. Anyone who will be operating and/or maintaining the flail shredder must read and clearly understand all Safety, Operating, and Service & Maintenance information presented in this manual.
OPERATION The Woods Flail Shredder is designed to pick up and shred crop and plant residue left in the field. Rotational power to the flails is provided by the tractor PTO. Be familiar with the flail shredder before starting. The owner is responsible for training operators in the safe operation of the flail shredder. WARNING Safety instructions are important! Read all attachment and power unit manuals; follow all safety rules and safety decal information.
1. Crossmember 2. Rubber belt shield 3. Skid assembly 4. Rubber belt shield 5. Body weldment 6. Flail tube assembly RH 7. Flail tube assembly LH 8. Woods model decal 9. Gearbox 10. Bearing assembly Figure 1. Flail Shredder Principal Components PRE-OPERATION CHECK LIST (OWNER'S RESPONSIBILITY) NOTICE ■ This Pre-Operation Check List is provided for the operator. It is important to follow for both personal safety and maintenance of the flail shredder.
Table 1: Tractor Horsepower (6-8) vs. Unit Width Width Minimum Horsepower 20′ 120 22′ 132 25′ 150 27′ 162 30′ 180 6. Drawbar (Pull-Type Models Only) The tractor drawbar must be set to provide 20” (508 mm), between the end of the PTO shaft and the center of the drawbar pin for 1-3/4 - 20, 1000 RPM drives. See Figure 4. This dimension will provide the required clearance for the CV (Constant Velocity) joint on the front of the driveline. NOTE: On Pull-Type models, do not cut driveline.
ATTACHING SHREDDER TO TRACTOR WARNING Keep bystanders away from equipment. 1. Place unit on a level, dry area free of debris and other foreign object. WARNING 1. Clear the area of all bystanders. 2. Attach the 3-point hitch to the unit but not the PTO driveline. 3. Raise the unit until the tractor PTO and gearbox shafts are the same height. 4. Measure the dimension between the shaft grooves on the tractor and implement ends. If this dimension is less than 34.
Without Quick Hitch Attachment: 10. Back tractor lower 3-point arms between lower mast plates and align with lower 3-point hole. 11. Place 1-3/4 OD spacer through 3-point arm pivot (both sides). 12. Push tractor’s 3-point arm to the inside and slide a 1-7/16 OD spacer between to take up the empty space. Secure with lower 3-point hitch pin assembly, 1-3/4 OD spacer, and 7/16 x 2 klik pin. 13. Repeat steps 5 and 6 for other side. 14.
Never allow riders on power unit or attachment. Do not allow bystanders in the area when operating, attaching, removing, assembling, or servicing equipment. Inspect and clear area of stones, branches, or other hard objects that might be thrown, causing injury or damage. Operators must be instructed in and be capable of the safe operation of the equipment, its attachments, and all controls. Do not allow anyone to operate this equipment without proper instructions. DP101 Figure 9.
NOTE: To avoid unnecessary wear on knives and related parts, never set the unit lower than the recommended setting. (See Balance Statement, page 5.) SET OPERATING HEIGHT “L” Flails “L” flails (Figure 13) work best when trash or crop residue is standing. Cup Flails Use stroke control spacers. The number and thickness should be equal on each cylinder to keep shredder level. Stroke Control Spacers Cup flails (Figure 14) can pick up material from the ground and work best in matted trash conditions.
Set the flail height after the wheels have been moved against the seed bed. Figure 16. Wheel Position DP14 STARTING THE SHREDDER 1. Run tractor engine at low idle. Figure 14. Cup Flails 2. Slowly engage PTO control to start the shredder. Setting Flail Height 1. Be sure wheels are set to follow in the center of furrow row. Set flails 3 to 6 inches (75 to 150 mm) above the ground. (See Balance Statement, page 5.) 2. Align the unit with the working area on or between rows on flat farming. 3.
Shut down unit and wait for moving parts to stop before approaching. NOTICE ■ Disengage PTO when making sharp turns. KEEP OUT OF Figure 17. Hazard Area GROUND SPEED Travel speed can vary between 3 and 8 mph (5 and 13 kmph) depending on the bulk of residue and terrain conditions. The operator is responsible for noting the condition of the work, setting the speed to obtain a quality shredding job, and maintaining control of the unit. CLEANING Speed may be increased if shredding quality is good.
END TOW OPERATION 3-Point Mounted Models: 1. While shredder is attached to 3-point hitch on tractor user 3-point to lift all four wheels off ground. Rotate and lock two wheels on right end of shredder in end transport position as shown in Figure 19. DP104 Figure 21. End Tow - Drawbar 5. An end tow hitch is also available as optional equipment for hooking shredder to quick hitch. DP102 Figure 19. Transport Position 2. Set shredder back on all four wheels using 3-point.
END TOW OPERATION Pull-Type Models 1. Raise all shredder lift cylinders to maximum lift height. Flip transport locks into position (see Figure 16). Lower cylinder on to transport lock. Make sure all cylinders have bottomed out. 2. Unhook hydraulic hose, PTO drive, and drawbar pin. Secure hoses and PTO drive for transport. Lift tongue and rotate into position on shredder body as shown in Figure 24. STORAGE WARNING Block equipment securely for storage.
SERVICE & MAINTENANCE grease with extreme pressure (EP) performance. An SAE multi-purpose lithium-based grease is also acceptable. WARNING Before dismounting power unit or performing any service or maintenance, follow these steps: disengage power to equipment, lower the 3-point hitch and all raised components to the ground, operate valve levers to release any hydraulic pressure, set parking brake, stop engine, remove key, and unfasten seat belt.
Figure 25. PTO Driveline Lubrication Points A. Daily or 8 hours B. 25 hours C. 40 hours D. Check Daily/Change Annually Figure 26. Lubrication Points Daily or every 8 hours of operation 1. Lubricate PTO U-Joints and over-running clutch. 2. Check gearbox daily or every 8 hours of operation. See Figure 26 for gearbox oil fill location. Every 25 hours of operation 1. Lubricate PTO driveline telescoping section (one location, Position B, Figure 25). 2. Lubricate rotor end bearings. (See Figure 27).
Annually 1. Change gearbox oil. Refill with SAE 85W90 gear oil. Capacity: 2-1/2 U.S. quarts (110 oz.). See Figure 30. DP106 Figure 27. Gearbox Oil Fill Location DP15 GEARBOX OIL DRAIN Figure 30. Gearbox Oil Drain Location 2. Repack wheel bearings. See Figure 31. DP107 DP110 Figure 28. Rotor End Bearing Lubrication Point Figure 31. Wheel Bearings 3. Lubricate pivot tube (2 locations each pivot tube). See Figure 32. Every 40 hours of operation - Figure 29 1.
4. Lubricate caster pivot bearings as shown in Figure 33. DP108 Figure 33. Wheel Caster Bearing Lubrication Points LUBRICATION SERVICE RECORD NOTE: See page 25 through page 28 for details. Copy this page to continue service record.
GEARBOX OIL LEAKAGE NOTICE ■ Major oil leakage from the gearbox shaft seal area is not acceptable and could cause the gearbox to fail due to lack of lubrication and cooling. It is the operator’s responsibility to check the gearbox oil level per the Lubrication Service Table. Before checking gearbox oil level, shut down the shredder for a couple of hours to allow the oil to drain back into the reservoir for the most accurate reading. Proper oil level should be between the full and add lines on dipstick.
Figure 34. Acceptable Oil Leakage GEARBOX DRAIN PLUG DP114 DP16 Figure 35. Drain Plug (Underside of Unit) 7. Re-install and tighten drain plug. 8. Dispose of used oil in an approved container. 9. Add SAE 85W90 gear oil through the dipstick cover. Use the dipstick to check the oil level (Figure 36) and add oil accordingly. 10. Re-install and tighten fill plug. 11. Reconnect PTO driveline and hydraulic lines. 12. Remove blocks or safety stands. Figure 36.
7. Loosen mounting bolts on one wheel assembly. 8. Slide assembly along the frame tube to new position (see Figure 37). 9. Tighten mounting bolts to specified torque level. 5. Loosen and remove the worn knife and its opposite on the other side of the rotor. Discard worn knives and their mounting hardware. 6. Replace with new knives and mounting hardware (see Figure 38). DP13 DP116 Figure 37. Positioning Wheel Assembly 10. Remove safety stands or blocks. Figure 38.
Factory balanced replacement rotors are available through your local Woods dealer. Contact Woods Technical Service for re-balance options or further details. Follow the procedure below if rotor removal or replacement is required. CAUTION DP117 Figure 39. Front Rubber Shield Flaps 4. Replace damaged flap with new flap and secure with correct hardware. NOTE: Use only genuine Woods parts when replacing flaps. SERVICING ROTORS (FLAIL TUBES) WARNING Do not handle blades with bare hands.
NOTE: When re-installing rotors, the gear coupling grease fitting will need to be temporarily removed to allow for air to purge from the coupler assembly during installation. After successful installation, reinstall grease fitting and re-service. LOCKING COLLAR SET SCREW LOCKING COLLAR FS211 PEER SHAFT FOR REMOVAL: TAP WITH A HAMMER AND PUNCH AFTER LOOSENING SET SCREW. FOR INSTALLATION: REVERSE PROCEDURE MAN0506003 7. Reinstall bearing plate assembly and bolts, and apply appropriate torque. 8.
Figure 42. Stub Shaft Assembly Removing the Driveline 1. Shut off tractor and disengage PTO. 2. Disconnect driveline from PTO shaft. 3. Remove the bolts and clamp that attaches the clutch to the shredder’s input shaft. NOTE: The shaft is heavy. Grasp the clutch firmly with both hands and slide off the input shaft. Rebuilding Friction Pack Assembly 1. Place one new friction disc, then separator plate, then second friction disc into housing. 2.
Rebuilding Overrunning Clutch Disassembly 1. Remove the four bolts that secure the friction pack. Remove the friction pack. 2. Using screwdriver and pliers, remove the retaining ring that holds the overrunning clutch together. 3. Slide the collar and washer off the clutch hub, noting the orientation of the collar for reinsertion. 4. Remove and discard the keys and leaf springs. Inspection 1. Inspect the steel parts for wear and replace if necessary. Figure 44. Weasler Automatic Clutch (30K) 2.
NOTES 36 Service & Maintenance MAN0943 (11/1/2013)
TROUBLESHOOTING The Woods Flail Shredder uses swinging flails to pick up and shred crop residue left in the field. It is a simple and reliable system that requires minimal maintenance. The following table lists problems, causes, and solutions that you may encounter. If you encounter a problem that is difficult to solve even after reading through this table, please call your local Woods dealer. When calling, please have this manual and your unit’s serial number ready.
WORKSHEET FOR CONTOUR FLAIL PATTERNS 38 Contour Flail Patterns MAN0943 (11/1/2013)
WORKSHEET FOR CONTOUR FLAIL PATTERNS 24’ MAN0943 (11/1/2013) Contour Flail Patterns 39
ASSEMBLY DEALER SET-UP INSTRUCTIONS WARNING Do not allow bystanders in the area when operating, attaching, removing, assembling, or servicing equipment. Do not handle blades with bare hands. Careless or improper handling may result in serious injury. NOTICE ■ For units shipped on aft end, the dipstick ship- ping plug must be removed before shredder operation. Replace plug with dipstick in filler tube after shredder has been removed from truck and leveled.
3. Attach crossmember to strut uprights. Tighten all mounting hardware at this time per torque chart, Figure 47. 8. Connect hoses to tractor and cycle cylinder in and out to remove air from system. Check for leaks at this time. 9. While shredder is setting on skids, retract cylinders fully until cast yokes are high enough to mount wheels. Torque wheel nuts per torque chart. 10. Check tire pressure. Recommended tire pressure is 30 PSI. 11. Tighten mounting bolts to their specified torque.
INSTALL PULL-TYPE HITCH MANUAL STORAGE TUBE INSTALLATION 1. Install hitch to 3-point lower mounts using pins and klik pins. 2. See page 50 for parts breakdown. Mount the manual tube to the inside of the shredder side sheet, using three 3/8 x 1-1/4" hex bolts, washers, and 3/8" nuts. Mounting holes are located above the bearing plate (see Figure 53). 3. Attach tow chain to hitch. DP18 Figure 53. Manual Tube Installed RUBBER BELTING INSTALLATION Figure 51. Pull-Type Hitch Installed 1.
8. Secure wiring harness module to top of shredder using self tapping screw (30). 9. Connect 7-pin connector of wiring harness to tractor and test all light functions before actual use. 1. Rubber flap 2. Flap bracket, right 3. Flap bracket, left 5. flap rod 6. Swing flap bar, mast plate 7. Swing flap bar 8. 3/8 NC x 1 Carriage bolt 9. 3/8 NC Flange lock nut 10. 3/16 x 1-1/2 Cotter pin Figure 54. Rubber Flap Installation (15’ Shown) SAFETY LIGHT INSTALLATION 1. Remove all components from shipping carton.
END TOW HITCH INSTALLATION 1. Attach lower end tow hitch mount (4) using carriage bolts (26), and lock nuts (25). 2. Attach tongue lockup bracket (3) using carriage bolts (26), and locknuts (25). 3. Bolt hitch (1) to tow hitch mount brackets (33) using cap screws (27) and locknuts (28). 4. Attach hose bracket (13) to shredder using carriage bolts (26), flat washer (14) and locknuts (25). 5. Secure tongue (1) to tow hitch mount (4) using cap screws (27) and locknuts (28). 6. Install safety chain. 7.
Assemble Motor and Blade - Figure 58 1. Install elbow (8), adapter (9), elbow (10) and hose (11) to the IN or PRESSURE side of the hydraulic motor. 2. Install adapter (23) and hose (11) to the OUT or RETURN side of the motor. 3. Place motor (4) inside motor housing (2) and secure using six 9/16 NC x 1-1/2 cap screws (7) lock nuts (6). Make sure OUT or RETRUN side of motor is on the open side of the motor housing. Torque hardware to 171 lbs-ft. Install Motor Housing - Figure 59 1.
Figure 60. Hose Assembly 6. Route hose (11) from the IN side of the motor between shredder and rockshaft and attach it to tee (12) on the left side of the center plate. 7. Route hose (11) from the OUT side of the motor between shredder and rockshaft and attach it to tee (12) on the right side of the center plate. RETURN 20. 66 24. 50530315 25. 50530263 33. 4378 34. 2472 35. 5283 36.
DEALER CHECK LISTS PRE-DELIVERY CHECK LIST (DEALER’S RESPONSIBILITY) Inspect the equipment thoroughly after assembly to make sure that it is set up properly before delivering it to the customer. The following check lists are a reminder of points to inspect. Check off each item as it is found satisfactory or after proper adjustment is made. ___ Check that all safety decals are installed and in good condition. Replace if damaged. ___ Properly attach implement to tractor and make all necessary adjustments.
NOTES 48 Dealer Check Lists MAN0943 (11/1/2013)
PARTS INDEX FLAIL SHREDDER Center Drive FRAME ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 - 51 FLAIL TUBE ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 STRUT AND CASTER ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . .53 SAFETY LIGHT KIT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 - 55 WEASLER PTO SHAFT WITH TORQMASTER CLUTCH . . . . . . 56 - 58 WEASLER 24K TORQMASTER CLUTCH . . . . . . . . .
CENTER DRIVE FLAIL SHREDDER FRAME ASSEMBLY 50 Parts MAN0943 (11/1/2013)
CENTER DRIVE FLAIL SHREDDER FRAME ASSEMBLY PARTS LIST REF 1 PART 1 2 NSS NSS NSS NSS NSS ---------- 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 22a 23 24 25 26 27 28 29 30 31 35 1029365 1029372 1029550 1029554 7144 1004814 29547 1012170 1010120 1013067 1003828 1013049 1030513 90315407 1012175 50030338 90109126 1013114 1019755 20020553 90029204 * 1016186 1016187 20030151 20030961 20030960 20030959 1020013 90039030 37431 923 QTY 1 1 1 1 1 - DESCRIPTION S20CD Shredder Body S22CD Shredder Body
FLAIL TUBE ASSEMBLY REF LEFT PART # RIGHT PART # QTY 1 1 1013109LK 1013108LK 1013109HD 1013108HD 1 1 1 1013109CP 1013108CP 1 1 1 1016179LK 1016178LK 1016179HD 1016178HD 1 1 1 1016179CP 1016178CP 1 1 1 1012169LK 1012168LK 1012169HD 1012168HD 1 1 1 1012169CP 1012168CP 1 1 1 1013119LK 1013118LK 1013119HD 1013118HD 1 1 1 1013119CP 1013118CP 1 1 1 1029355LK 1029354LK 1029355HD 1029354HD 1 1 1 1029355CP 1029354CP 1 DESCRIPTION 20’ Flail tube w/knives 20’ HD Cotton tube w/knives
STRUT AND CASTER ASSEMBLY REF PART NO QTY DESCRIPTION REF PART NO QTY DESCRIPTION 1 1029554 4 Caster Pivot Assembly 16 20031766 8 Bearing, Caster Pivot 2 1030508 4 Caster Assembly 17 20031219 4 Retainer Pin 3 90509009 4 Dust Cap 18 90001221 4 1/2 NF x 1 HHCS, GR5 4 20378 4 7/8 NF Slotted Nut 19 90025030 2 3/4 x 6 Hitch Pin 5 28539 4 7/8 Washer 20 22411 4 3/16 Klik Pin 6 2303 4 Bearing Cone N/S 90509070 4 Tire, 9.
END TOW AND SAFETY LIGHT ASSEMBLY 54 Parts MAN0943 (11/1/2013)
END TOW ASSEMBLY AND SAFETY LIGHT PART LIST REF PART 1 1023125 2 19407 3 5 QTY DESCRIPTION REF PART QTY 1 Hitch 17 62521 * 8 1/4 NC Flange Locknut 1 Tow Chain, 10,000 lbs 18 10378 * 8 1/4 NC x 1" HHCS 1029565 1 Tongue Lock-Up 25 11900 * 9 1/2 NC Flange Lock Nut 1019834 1 Light Mount 26 90001751 * 6 90401151 1 Wire Harness 27 90001381 * 7 90507121 12 Adhesive Back Clamp 28 19025 * 8 24611 1 Slow Moving Vehicle Sign 29 9 50520563 2 Dual Safety Light Arm 30 1 Jack
TYPE A - WEASLER® 24K PULL-TYPE PTO SHAFT WITH TORQMASTER CLUTCH S20CD, S22CD, S25CD, S27CD PULL-TYPE MODELS REF PART QTY 1 2 3 4 5 6 7 8 9 19837 90318121 58759 19840 58760 90318183 19846 18864 55648 1 1 2 1 1 1 2 1 1 DESCRIPTION Slide lock repair kit 1.75 ID Slide lock yoke asy 1.75 ID Cat 6 CV U-joint repair kit CV Bell shield CV Body with fitting Yoke & shaft 26.
TYPE B - WEASLER® 24K PULL-TYPE PTO SHAFT WITH TORQMASTER CLUTCH S20CD, S22CD, S25CD, S27CD PULL-TYPE MODELS REF A 1 2 3 4 5 6 7 8 9 PART 1016109 19837 1033105 1033107 19840 1033106 1033109 19846 18864 55648 QTY 1 1 1 2 1 1 1 2 1 1 DESCRIPTION PTO complete 1-3/4 20 spline Slide lock repair kit 1.75 ID Slide lock yoke asy 1.
WEASLER® 24K 2-POINT & 3-POINT PTO SHAFT WITH TORQMASTER CLUTCH S20CD, S22CD, S25CD, S27CD 3-POINT MODELS 1 3 2 4 5 6 7 9 8 5 10 3 11 CD6523 REF PART QTY 1 2 3 4 4 5 6 7 19837 90317418 1016113 90318183 90318074 19846 18864 1010803 1 1 2 1 1 1 1 1 7 1010813 1 8 9 1010804 33347 1 1 DESCRIPTION Slide lock repair kit 1.75 ID Slide lock yoke asy 1.75 ID U-joint cross & bearing kit Yoke & shaft 26.8 center-end -orYoke & shaft 32.
WEASLER® 24K TORQMASTER CLUTCH ASSEMBLY S20CD, S22CD, S25CD, S27CD MODELS REF 1 PART 1010831 QTY 1 DESCRIPTION Yoke, Clamp style with overrunning clutch & hub asy (10 mm bolts) (includes Items 2 - 10) 1A 1019629 1 Overrunning clutch repair kit (includes Items 2, 6, 7, 9 & 10) 2 90318165 1 Wave spring 3 90318154 1 Set screw, .312-18 x .25 long 4 90317541 31 Ball, 1/4" dia.
WEASLER® AUTOMATIC CLUTCH ASSEMBLY S30CD,MODELS REF QTY DESCRIPTION 1019811 - Automatic clutch asy complete 1 1019813 1 Yoke & hub, 30K auto 2 1019814 1 Clutch pack, 30K auto 3 1010833 1 Hub clamp assembly 1-3/4 4 1025874 6 HHCS, M12-1.75P x 20 mm CL10.9 flanged head 5 90318165 1 Wave spring 6 90318154 1 Set screw, .312-18 x .
WEASLER® 30K 3-POINT PTO SHAFT WITH AUTOMATIC CLUTCH (OPTIONAL) S30CD 3-POINT MODELS REF PART QTY DESCRIPTION PTO Shaft complete 1-3/4 20-spline 30K 3-point with automatic clutch Slide lock repair kit 1.75 ID 1-3/4 20-Spline yoke U-Joint cross & bearing kit 55E Yoke & shaft, 1.69 20-spline, 30.6 long -ORYoke & shaft, 1.69 20-spline, 26.
TYPE B - WEASLER® 30K PULL-TYPE PTO SHAFT WITH AUTOMATIC CLUTCH (OPTIONAL) S30CD PULL-TYPE MODELS REF PART QTY A 1019820 - 1 2 3 4 5 6 19837 1033105 1033107 1033106 1033109 1009065 1 1 2 1 1 2 DESCRIPTION PTO Shaft complete 1-3/4 20-spline 30K pull-type with automatic clutch Slide lock repair kit 1.75 ID Slide lock yoke assembly CV U-Joint repair kit, 55E CV Body with fitting Yoke & shaft (1.
CENTER DRIVE GEARBOX REF QTY DESCRIPTION A 1 2 3 1013049 1019782 1019783 1019784 PART 1 1 1 1 4 5 6 7 8 9 10 11 12 13 14 15 16 90315546 90101150 90101152 1019785 1019787 90039030 90109125 90503078 90003033 90501159 90101328 NSS NSS NSS 1 1 2 4 3 1 3 2 8 1 1 - Complete gearbox, Series 800 Casting, Threaded holes Casting, Non-threaded holes Pinion shaft/gear asy 27T with bearing cones & bearing cups Cross shaft/gear asy 20T Bearing cone Bearing cup Bolt, 3/8-16 x 2.75 SHCS Guard, seal Snap ring 1.
RUBBER BELTING REF PART QTY 1 1 1 2 2 2 3 3 3 3 4 4 4 4 1012202 1012202 1012202 1022647 1022647 1022647 1022648 1022650 1022649 1029560 1016195 1019763 1016188 1029561 6 8 8 6 8 8 2 2 2 2 2 2 2 2 DESCRIPTION Rubber belting (20 ft & 22 ft) Rubber belting (25 ft & 27 ft) Rubber belting (30 ft) Belt bar (20 ft & 22 ft) Belt bar (25 ft & 27 ft) Belt bar (30 ft) Belt bar (20 ft) Belt bar (22 ft) Belt bar (27 ft) Belt bar (30 ft) Rubber belting (20 ft) Rubber belting (22 ft) Rubber belting (27 ft) Rubber b
CENTER DEFLECTOR REF 1 2 3 PART QTY 1016151 301109 * 11900 * * 1 4 4 DESCRIPTION Center deflector 1/2 NC x 1-1/4 Carriage bolt GR5 1/2 NC Flange lock nut Standard hardware, obtain locally HYDRAULIC HOSE ASSEMBLY REF 4 19 20 21 22 23 24 31 32 PART QTY DESCRIPTION 12422 2 Hose, .25 x .25NPT x 90L 31239 6 1/4 F Swivel Union Tee 66511 2 1/2 NPT Male Coupler 8572 8 3/8 x 1/4 x 90° Swivel 28522 8 Hose, .25 x .25 NPT x 54L 11893 10 1/4 NPTF Adapter 31208 4 Hose, .25 x .
RUBBER FLAP REF PART QTY 1 1 1 1 1 2 2 2 2 3 3 3 3 3 4 4 50531089 50531089 50531089 50531089 50531089 1022659 1022659 1022659 1022659 1022660 1022660 1022660 1022660 1022660 1022661 1022662 18 20 24 26 30 4 5 6 7 3 4 5 6 7 2 2 DESCRIPTION Rubber flap (12" - 20 ft) Rubber flap (12" - 22 ft) Rubber flap (12" - 25 ft) Rubber flap (12" - 27 ft) Rubber flap (12" - 30 ft) Flap bracket, right (20 ft) Flap bracket, right (22 ft & 25 ft) Flap bracket, right (27 ft) Flap bracket, right (30 ft) Flap bracket, le
CENTER CUTTER KIT (OPTIONAL) 24 - 50530315 25 - 50530263 WARNING ADVERTENCIA HIGH-PRESSURE FLUID HAZARD To prevent serious injury or death: 1. Relieve pressure on system before repairing, adjusting, or disconnecting. 2. Wear proper hand and eye protection when searching for leaks. Use wood or cardboard instead of hands. 3. Keep all components in good repair. PELIGRO DE FLUIDO BAJO ALTA PRESION Para evitar heridas graves o la muerte: 1.
BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly.
BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. SAE Bolt Thread Sizes 5/16 3/8 1/2 IN MM 5/8 3/4 7/8 1 2 3 4 5 6 7 25 50 75 100 125 150 175 Metric Bolt Thread Sizes 8MM 10MM 12MM 14MM 16MM 18MM ABBREVIATIONS AG .............................................................. Agriculture ASABE.................... American Society of Agricultural & Biological Engineers (formerly ASAE) ASAE .......
INDEX Setting Operating Height 20 Setting Outer Trailing Wheels 21 Starting the Tractor 21 Stopping the Tractor 21 Turning 22 ASSEMBLY Dealer Set-Up Instructions 40 Optional Equipment Center Cut Kit Installation 44 Rubber Belting Installation 42 Rubber Flap Installation 42 Safety Light Kit Installation 43 Optional Equipment Rubber Flaps 19 Pre-Operation Check List (Owner’s Responsibility) 15 Preparing for Operation 19 Principal Components 14 Removing Shredder from Tractor 18 Storage 24 Tractor horsepower
WARRANTY All Models Except Mow’n MachineTM Zero-Turn Mowers Please Enter Information Below and Save for Future Reference. Date Purchased: ____________________________ From (Dealer): __________________________________________ Model Number: ____________________________ Serial Number: __________________________________________ Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship.
WARRANTY (Replacement Parts For All Models Except Mow’n MachineTM Zero-Turn Mowers and Woods BoundaryTM Utility Vehicles) Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship for a period of ninety (90) days from the date of delivery of the product to the original purchaser with the exception of V-belts, which will be free of defect in material and workmanship for a period of 12 months.
