MODEL W1779 18 GAUGE STAPLER KIT OWNER'S MANUAL Phone: (360) 734-3482 • Online Technical Support: tech-support@shopfox.biz COPYRIGHT © JUNE, 2007 BY WOODSTOCK INTERNATIONAL, INC., REVISED DECEMBER, 2007 (JM) WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
����������������������������������������������������������������������� �������������������������������������������������������������� ���������������������������������������������������������������������� �������������������������������������������������������������������� ������������������������ ����������������������������������������������������������������������� ������������������������������������������������������������������������ �������������������������������������������������������������������
Model W1779 18 Gauge Stapler Kit SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below.
Model W1779 18 Gauge Stapler Kit Safety Instructions for Pneumatic Tools 10. USE PROPER AIR HOSE for the tool. Make sure your air hose is in good condition and is long enough to reach your work without stretching. 17. DISCONNECT TOOLS before servicing, changing accessories, or moving to another location. 11. WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Non-slip footwear is recommended.
Model W1779 18 Gauge Stapler Kit Additional Safety Instructions for Staplers 1. HAND INJURIES: Do not place your hands near the staple point of entry. A staple can deflect and tear through the surface of the workpiece, puncturing your hand or fingers. 5. HOSE USAGE: Make sure your air hose is designed for the tool in use, is in good condition, and is long enough to reach your work without stretching. However, an overly long air hose in the work area may be a tripping hazard. 2.
Model W1779 18 Gauge Stapler Kit INTRODUCTION Woodstock Technical Support Tool Data Staple Size .......................... 18 Gauge Staple Length ........................... 1⁄2"-1" Staple Crown ...............................1⁄4" Magazine Capacity ...............100 Staples Air Inlet................................ 1⁄4" NPT Weight ....................................2 lbs. Operating Pressure ............... 60-100 PSI This tool has been specially designed to provide many years of trouble-free service.
Model W1779 18 Gauge Stapler Kit Compressed Air System The Model W1779 is designed to be operated at 60-100 PSI using clean, dry, regulated, compressed air. Do not exceed the 120 PSI maximum operating pressure for your model. Before using your new stapler, regulate the air pressure to find the optimum setting within the specified operating range. Start by testing the stapler at a low setting, then increase the air pressure as needed for satisfactory results.
Model W1779 18 Gauge Stapler Kit SETUP Unpacking This tool has been carefully packaged for safe transportation. If you notice the tool has been damaged during shipping, please contact your authorized Shop Fox dealer immediately. Inventory The following is a description of the main components shipped with the Model W1779. Lay the components out to inventory them. Note: If you can't find an item on this list, check the mounting location on the tool or examine the packaging materials carefully.
Model W1779 18 Gauge Stapler Kit Safety Nose Mechanism — If the stapler fires when the trigger is pulled, without the safety nose mechanism being depressed, then the stapler is not working properly. A safety mechanism on the nose of the stapler protects against accidental firing. When the trigger is pressed, the stapler will not fire until the safety nose mechanism is depressed. — If you find that the safety nose mechanism is not working properly, check the lubrication of its sliding components.
Model W1779 18 Gauge Stapler Kit OPERATIONS Loading 4. Slide the staples all the way down to the nose of the stapler. When replacing staples in your Model W1779, follow these guidelines: 5. Release the magazine pusher by pulling back and up. Gently slide the pusher forward; do not let the pusher snap against the staple stick. Gauge: .......................................18 Length: ................................. 1⁄2"–1" Capacity: .................................. 100 Crown: ........................
Model W1779 18 Gauge Stapler Kit Single/Bump Fire Operation DO NOT place your hands near the staple point of entry. A staple can deflect and tear through the surface of the workpiece, puncturing your hand or fingers. The stapler is designed to fire one staple at a time, or one after another, using the trigger switch—this is known as "bump fire.
Model W1779 18 Gauge Stapler Kit Clearing Jammed Staples To operate your stapler in bump fire mode, do these steps: 1. Push the trigger switch IN (Figure 7). A jammed staple must be cleared before using the stapler again. To clear a jammed staple from the discharge area, do these steps: 1. DISCONNECT STAPLER FROM THE AIR SUPPLY! 2. Pull back and latch the magazine. 3. Remove the staple stick from the magazine. Figure 7. Trigger switch, bump fire mode. 4.
Model W1779 18 Gauge Stapler Kit Replacing Pistons and O-Rings 6. Open the nose cover as if to clear a jammed staple. Under heavy use, a piston or piston shaft may wear out. Replacement is quick and easy. Contact your authorized Shop Fox dealer to obtain the Piston Repair Kit (part number X1779001). 7. Watch the discharge area and push the top of the piston with your finger. You will see the piston shaft slide down the discharge area. 8.
Model W1779 18 Gauge Stapler Kit CLEANING & LUBRICATION Cleaning Lubricating Use a good solvent to clean the nose assembly of the stapler. Always be sure that the stapler is dry before using it again. Standard pneumatic tool oil has been included with your new Shop Fox stapler to help maintain its useful life. Place two to three drops of oil in the stapler air inlet (as shown in Figure 9) before every use, or after 2 hours of continuous use. Do not allow dust, chips, sand, etc.
Model W1779 18 Gauge Stapler Kit PARTS BREAKDOWN 69 68 67 66 65 46 54 53 52 63 62 51 61 50 60 57 9 55 64 59 58 10 56 47 31 30 49 48 25 26 11 12 45 4445 46 38 43 42 37 13 36 41 35 45 39 45 40 29 19 34 18 20 21 33 28 23 32 66 22 67 27 24 6 8 5 7 14 15 17 16 4 70 3 71 1 2 -13-
Model W1779 18 Gauge Stapler Kit PARTS LIST REF PART�# DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 PISTON�REPAIR�KIT CARRYING�CASE HEX�WRENCH�4MM HEX�WRENCH�3MM AIR�PLUG�COVER 1/4"�NPT�MALE�CONNECT END�CAP O-RING�42�X�2.4 RUBBER�HANDLE�CASE LOCK�NUT�M4-.7 TALL�STOPPER CAP�SCREW�M4-.7�X�16 COMPRESSION�SPRING CAP�SCREW�M4-.7�X�6 DRIVE�NAIL�PLATE LEVER PUSHER SPRING�PIN SPRING�SEAT COMPRESSION�SPRING SET�SCREW�M3-.
Model W1779 18 Gauge Stapler Kit Troubleshooting Symptom Possible Cause Cause Possible Solution Air leaking at trigger valve area. 1. O-rings in trigger valve housing are damaged. 1. O-rings must be replaced & operation of safety nose must be checked. Air leaking between housing and hose. 1. Loose screws in housing. 2. Damaged O-ring. 3. Loose air fitting. 1. Tighten screws. 2. Replace O-ring 3. Tighten air fitting & use teflon tape. Air leaking between housing and cap. 1. Damaged seal. 1.
�������������������� ������������������������������������������������������������������������������������� �������������������������������������������������������������������������������� ����������������������������������������������������������������������������������������� �������������������������������������������������������������������������������� ��������������������������������������������������������������������������������������� �����������������������������������������������������������������
Warranty Registration Name ___________________________________________________________________________________ Street __________________________________________________________________________________ City _________________________ State ___________________________Zip ________________________ Phone # ______________________ Email __________________________Invoice # ___________________ Model #_________Serial #______________Dealer Name__________________Purchase Date___________ CUT ALONG DOTTED LINE The follo
FOLD ALONG DOTTED LINE Place Stamp Here WOODSTOCK INTERNATIONAL INC. P.O.