MODEL W1785 PALM NAILER OWNER'S MANUAL Phone: (360) 734-3482 • Online Technical Support: tech-support@shopfox.biz COPYRIGHT © JUNE, 2007 BY WOODSTOCK INTERNATIONAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
����������������������������������������������������������������������� �������������������������������������������������������������� ���������������������������������������������������������������������� �������������������������������������������������������������������� ������������������������ ����������������������������������������������������������������������� ������������������������������������������������������������������������ �������������������������������������������������������������������
Model W1785 Palm Nailer SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.
Model W1785 Palm Nailer Safety Instructions for Pneumatic Tools 10. USE PROPER AIR HOSE for the tool. Make sure your air hose is in good condition and is long enough to reach your work without stretching. 17. DISCONNECT TOOLS before servicing, changing accessories, or moving to another location. 11. WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Non-slip footwear is recommended.
Model W1785 Palm Nailer Additional Safety for Nailers 1. HAND INJURIES: Do not place your hands near the nail point of entry. A nail can deflect and tear through the surface of the workpiece, puncturing your hand or fingers. 5. HOSE USAGE: Make sure your air hose is designed for the tool in use, is in good condition, and is long enough to reach your work without stretching. However, an overly long air hose in the work area may be a tripping hazard. 2.
Model W1785 Palm Nailer INTRODUCTION Woodstock Technical Support Tool Data Nail Size ................................ 5d–70d Blows Per Minute ........................ 1000 Average Air Consumption ............. 5 CFM Operating Air Pressure ........... 70–100 PSI Air Inlet Fitting ....................... 1⁄4" NPT Weight ................................. 1.9 lbs. This Model W1785 Palm Nailer has been specially designed to provide many years of trouble-free service.
Model W1785 Palm Nailer Compressed Air System The Model W1785 is designed to be operated at 70-100 PSI using clean, dry, regulated, compressed air. Do not exceed the 120 PSI maximum pressure for your model. Before using your nailer, regulate the air pressure to find the optimum setting within the specified operating range. Start by testing the nailer at a low setting, then increase the air pressure as needed for satisfactory results.
Model W1785 Palm Nailer SETUP Unpacking This tool has been carefully packaged for safe transportation. If you notice the tool has been damaged during shipping, please contact your authorized Shop Fox dealer immediately. Inventory The following is a description of the main components shipped with the Model W1785. Lay the components out to inventory them. Note: If you can't find an item on this list, check the mounting location on the tool or examine the packaging materials carefully.
Model W1785 Palm Nailer OPERATIONS Operating 3. Hold the nail firmly in place with one hand as if using a regular hammer. If you have not read the safety instructions in this manual, do not operate the nailer. 4. Place the tip of the palm nailer over the end of the nail. When the ram pin touches the nail head, the nailer will automatically begin to hammer the nail into the workpiece.
Model W1785 Palm Nailer Replacing Pistons/ O-Rings 5. Take hold of the ram pin and pull the piston from the cylinder. 6. Place the new O-ring on the new piston, and apply a thin film of tool oil on the O-ring. Under heavy use, the piston or O-rings may wear out. Replacement is quick and easy. Contact your authorized Shop Fox dealer to obtain the Piston Repair Kit (Part Number X1785127), or the Complete O-Ring Kit (Part Number X1785128). 7. Insert the new piston in the cylinder.
Model W1785 Palm Nailer CLEANING & LUBRICATION Cleaning Lubricating Use a good solvent to clean the nose assembly of the nailer. Always be sure that the nailer is dry before using it again. Standard pneumatic tool oil has been included with your new Shop Fox nailer to help maintain its useful life. Place two to six drops of oil in the nailer air inlet (as shown in Figure 3) before every use, or after 2 hours of continuous use. Do not allow dust, chips, sand, etc.
Model W1785 Palm Nailer PARTS BREAKDOWN & PARTS LIST ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� REF PART�# DESCRIPTION REF PART�# 101 XPSB15M CAP�SCREW�M5-.8�X�20 115 X1785115 BUMPER�16�X�40�X�8 DESCRIPTION 102 X1785102 CAP 116 X1785116 AXLE�SLEEVE�8MM 103 X1785103 O-RING�53.5�X�2.
Model W1785 Palm Nailer TROUBLESHOOTING Symptom Possible Cause Possible Solution Air leaking at trigger valve area. 1. O-rings in trigger valve housing are damaged. 1. O-rings must be replaced & operation of safety nose must be checked. Air leaking between 1. Loose screws in housing. housing and hose 2. Damaged O-ring. 3. Loose air fitting. 1. Tighten screws. 2. Replace O-ring 3. Tighten air fitting & use teflon tape. Air leaking between 1. Damaged seal. housing and cap. 1. Replace damaged seals.
WARRANTY AND RETURNS Woodstock International, Inc. warrants all Shop Fox machinery to be free of defects from workmanship and materials for a period of two years from the date of original purchase by the original owner. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or accidents, lack of maintenance, or reimbursement of third party expenses incurred. Woodstock International, Inc.
Warranty Registration Name ___________________________________________________________________________________ Street __________________________________________________________________________________ City _________________________ State ___________________________Zip ________________________ Phone # ______________________ Email __________________________Invoice # ___________________ Model #_________Serial #______________Dealer Name__________________Purchase Date___________ CUT ALONG DOTTED LINE The follo
FOLD ALONG DOTTED LINE Place Stamp Here WOODSTOCK INTERNATIONAL INC. P.O.