MODEL D3736 Palm Finishing Sander OWNER'S MANUAL Phone: (360) 734-3482 • Online Technical Support: tech-support@shopfox.biz COPYRIGHT © MARCH, 2008 BY WOODSTOCK INTERNATIONAL, INC., WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/equipment. Failure to read, understand, and follow the instructions given in this manual may result in serious personal injury, including amputation, electrocution, or death. The owner of this machine/equipment is solely responsible for its safe use.
Model D3736 Palm Finishing Sander SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below.
Model D3736 Palm Finishing Sander 15. KEEP WORK AREA CLEAN AND WELL LIT. Clutter and dark shadows may cause accidents. 7. Only allow trained and properly supervised personnel to operate machinery. Make sure operation instructions are safe and clearly understood. 16. REMOVE ADJUSTING KEYS AND WRENCHES. Make a habit of checking for keys and adjusting wrenches before turning machinery ON. 8. KEEP CHILDREN AND VISITORS AWAY. Keep all children and visitors a safe distance from the work area. 17.
Model D3736 Palm Finishing Sander Additional Safety Instructions for the Palm Finishing Sander 1. HAND PROTECTION. DO NOT place hands near, or in contact with, sanding base during operation. Sandpaper has the capability of removing skin. 4. TRANSPORTING: DO NOT carry a plugged-in sander with your finger on the ON/OFF switch. Do not carry the sander by the power cord. 5. VIBRATION GENERATED INJURIES: Limit prolonged exposure to this tool and take regular breaks.
Model D3736 Palm Finishing Sander INTRODUCTION Woodstock Technical Support Tool Data Voltage.....................................110V Amps............................................ 2 Vibrations Per Minute................. 10,000 Sandpaper Size......41⁄4" x 41⁄2" (1⁄4 Sheet) Weight..................................31/2 lbs. This Model D3736 Palm Finishing Sander has been specially designed to provide many years of trouble-free service.
Model D3736 Palm Finishing Sander SETUP Unpacking This sander has been carefully packaged for safe transportation. If you notice the tool has been damaged during shipping, please contact your authorized Shop Fox dealer immediately. Inventory The following is a description of the main components shipped with the Model D3736. Lay the components out to inventory them. Note: If you can't find an item on this list, check the mounting location on the tool or examine the packaging materials carefully.
Model D3736 Palm Finishing Sander OPERATIONS Getting Started To test the sander, do these steps: Aluminum oxide and silicon carbide abrasives are an excellent choice because they last longer and are sharper than natural abrasives. 1. Plug the cord into a 110V outlet. 2. Move the switch (located at the front of the sander) to the “—” position to turn the sander ON, and move the switch to the “O” position to turn the sander OFF. The sander should run smoothly.
Model D3736 Palm Finishing Sander Using the Sander Tip: Try using the sandpaper that came with your sander as a template for cutting holes in new 1⁄4 sheets to match those on the bottom of the sander—so the dust bag can collect dust particles. Use a paper punch to cut the holes; or mark the holes, score them with a sharp knife, and cut them out. Determine the appropriate grit size for your project and sand the work evenly in the same direction as the grain of the wood.
Model D3736 Palm Finishing Sander MAINTENANCE General Keeping Tool Clean Regular periodic maintenance on your Model D3736 Palm Finishing Sander will ensure its optimum performance. Make a habit of inspecting your sander each time you use it. Check for the following conditions and repair or replace when necessary: • • • • • Your Model D3736 Palm Finishing Sander will give you years of trouble free service if you keep it clean and free of built-up dust or grime.
Model D3736 Palm Finishing Sander D3736 PARTS BREAKDOWN (- ( ), (. (+ ) )0 (/ (0 - (, ** , )* . )) )( )' / + *, )+ * 0 *+ )0 )+ (' *' (( )- )/ () ** *- (* ).
Model D3736 Palm Finishing Sander D3736 PARTS LIST REF PART # DESCRIPTION REF PART # DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 XD3736001 XD3736002 XD3736003 XD3736004 XD3736005 XP609 XP627 XD3736008 XP6000 XD3736010 XD3736011 XD3736012 XD3736013 XD3736014 XPSW07 XD3736016 XD3736017 TOP HOUSING COVER LEFT HOUSING RIGHT HOUSING STATOR ROTOR BALL BEARING 609 BALL BEARING 627 ALUMINUM FAN BALL BEARING 6000ZZ PARTITION SPACER BASE PLATE FOAM PLATE TOGGLE BAR SWITCH POWER CORD GUARD POWER COR
Model D3736 Palm Finishing Sander Troubleshooting Symptom Possible Cause Possible Solution Reduced amount of material removed by sander, quality of finish decreases, sander slides easily across workpiece. 1. Sandpaper clogged with paint or glue. 2. Sandpaper grit dull. 1. Replace sandpaper. Sander generates excessive dust particles. 1. Dust bag full. 2. Holes on sandpaper not aligned with holes in sander base. 3. Sandpaper lacks holes. 1. Empty dust bag. 2.
N8II8EKP 8E; I
Warranty Registration Name____________________________________________________________________________________ Street___________________________________________________________________________________ City__________________________ State____________________________Zip_________________________ Phone #_______________________ Email___________________________Invoice #____________________ Model #_________Serial #______________Dealer Name__________________Purchase Date___________ The following information is give
FOLD ALONG DOTTED LINE Place Stamp Here Woodstock international inc. p.o.
