MODEL W1764 1/8 HP POWER FEEDER OWNER'S MANUAL (FOR MODELS MANUFACTURED SINCE 1/14) Phone: (360) 734-3482 • Online Technical Support: tech-support@shopfox.biz COPYRIGHT © JUNE, 2007 BY WOODSTOCK INTERNATIONAL, INC. REVISED FEBRUARY, 2014 (BL) WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death. The owner of this machine/tool is solely responsible for its safe use.
INTRODUCTION......................................2 Woodstock Technical Support................... 2 SETUP............................................... 11 Unpacking........................................ 11 Inventory......................................... 11 Cleaning Machine................................ 12 Assembly.......................................... 13 Base Mounting................................... 16 Test Run........................................... 18 SERVICE..........................
INTRODUCTION Model W1764 (For Machines Mfg. Since 1/14) INTRODUCTION Woodstock Technical Support Woodstock International, Inc. is committed to customer satisfaction. Our intent with this manual is to include the basic information for safety, setup, operation, maintenance, and service of this product. In the event that questions arise about your machine, please contact Woodstock International Technical Support at (360) 734-3482 or send e-mail to: tech-support@shopfox.biz.
MACHINE MACHINE SPECIFICATIONS SPECIFICATIONS Phone #: (360) 734–3482 • Online Tech Support: tech–support@shopfox.biz • Web: www.shopfox.biz MODEL W1764 1/8 HP POWER FEEDER Motor Type ................................................................................................. Universal Variable Speed Horsepower .............................................................................................................. 1/8 HP Voltage ...................................................................
INTRODUCTION Model W1764 (For Machines Mfg. Since 1/14) Shipping Dimensions Type .................................................................................................................. Cardboard Content ................................................................................................................. Machine Weight .................................................................................................................... 27 lbs. Length/Width/Height .......................
INTRODUCTION Model W1764 (For Machines Mfg. Since 1/14) Controls and Features Rotation Position Lock Lever Horizontal Position Lock Lever Dust Port ⁄8 HP Motor 1 Vertical Position Lock Lever Horizontal Movement Crank Power Feeder Handle Ball Joint Lock Handle Figure 22. Controls and features. To reduce your risk of serious injury, read this entire manual BEFORE using machine.
Model W1764 (For Machines Mfg. Since 1/14) SAFETY SAFETY For.Your.Own.Safety, Read.Manual.Before.Operating.Machine The. purpose. of. safety. symbols. is. to. attract. your. attention. to. possible. hazardous. conditions.. This. manual.uses.a.series.of.symbols.and.signal.words.intended.to.convey.the.level.of.importance.of.the. safety.messages..The.progression.of.symbols.is.described.below..Remember.that.safety.messages.by. themselves. do. not. eliminate. danger. and. are. not. a. substitute. for. proper.
Model W1764 (For Machines Mfg. Since 1/14) FORCING.MACHINERY..Do not force machine. It will do the job safer and better at the rate for which it was designed. NEVER.STAND.ON.MACHINE..Serious injury may occur if machine is tipped or if the cutting tool is unintentionally contacted. HAZARDOUS.DUST..Dust created while using machinery may cause cancer, birth defects, or long-term respiratory damage.
Model W1764 (For Machines Mfg. Since 1/14) SAFETY Additional Safety for Power Feeders MAIN.INJURY.HAZARDS:.Death,.amputation,.or.crushing.injuries.from.getting.entangled.in. moving.parts—which.may.include.being.pulled.into.the.cutting.tool.on.attached.machinery;. death,.blindness,.broken.bones,.or.bruises.from.being.struck.by.an.ejected.workpiece. (kickback)..To.minimize.your.risk.of.these.hazards,.always.heed.the.following.information: ATTACHED.MACHINERY.
Model W1764 (For Machines Mfg. Since 1/14) ELECTRICAL Circuit Requirements This machine must be connected to the correct size and type of power supply circuit, or fire or electrical damage may occur. Read through this section to determine if an adequate power supply circuit is available. If a correct circuit is not available, a qualified electrician MUST install one before you can connect the machine to power. The. machine. must. be. properly. set. up. before. it. is. safe. to. operate.. DO. NOT. connect.
Model W1764 (For Machines Mfg. Since 1/14) Grounding Requirements ELECTRICAL This machine MUST be grounded. In the event of certain types of malfunctions or breakdowns, grounding provides a path of least resistance for electric current to travel—in order to reduce the risk of electric shock. Improper connection of the equipment-grounding wire will increase the risk of electric shock. The wire with green insulation (with/without yellow stripes) is the equipmentgrounding wire.
Model W1764 (For Machines Mfg. Since 1/14) SETUP Unpacking This machine has been carefully packaged for safe transportation. If you notice the machine has been damaged during shipping, please contact your authorized Shop Fox dealer immediately. Inventory The following is a description of the main components shipped with the Model W1764. Lay the components out to inventory them. Keep machine disconnected from power until instructed otherwise. Qty Box Inventory (Figures 24 & 25) A. Base...................
Model W1764 (For Machines Mfg. Since 1/14) Cleaning Machine To prevent corrosion during shipment and storage of your machine, the factory has coated the bare metal surfaces of your machine with a heavy-duty rust prevention compound. If you are unprepared or impatient, this compound can be difficult to remove.
Model W1764 (For Machines Mfg. Since 1/14) Assembly To correctly position this power feeder on your table top, completely assemble the power feeder first, then refer to Base Mounting on Page 16. With the power feeder unit completely assembled, it will be easier to determine where on the table top to drill your base mounting holes, so you can take advantage of the full range of power feeder swing and adjustments.
Model W1764 (For Machines Mfg. Since 1/14) 9. Place the arm into the arm bracket so the teeth of the gear and arm mesh, as shown in Figure 29. Arm Bracket Arm Note: No lubrication is required for the gear or rack teeth. Oil or grease will gather debris making the horizontal adjustment of the power feeder difficult. 10. Secure the arm bracket cover onto the arm bracket with three M10-1.5 x 35 hex bolts and washers (see Figure 30).
Model W1764 (For Machines Mfg. Since 1/14) 15. Lightly oil the T-handle threads shown in Figure 32. Note: No lubrication is required for the arm bracket and the elbow clamp connection. Oil Threads 16. Position the arm bracket onto the elbow clamp, as shown in Figure 33. 17. Thread the T-handle into the elbow clamp so both assemblies are secure, as shown in Figure 33. 18. Use the levers to lock the power feeder into position, such as the example shown in Figure 34. Figure 32. Arm bracket handle threads.
Model W1764 (For Machines Mfg. Since 1/14) Base Mounting Assemble the power feeder before you mount the base to determine where on the table top to drill your base mounting holes, so you can maximize power feeder swing and adjustment options. Also, you must be able to adjust the power feeder so it points towards the machine fence slightly (see Figure 35). In other words, the tracking of the power feeder must be toed-in approximately 1° to 1.
Model W1764 (For Machines Mfg. Since 1/14) Through-Bolt Mounting We recommend that you mount your new power feeder to the machine table with through-bolts, nuts and washers (see Figure 36). This option will give the most rigidity and clamping strength to prevent the feeder base from twisting out of alignment during use.
Model W1764 (For Machines Mfg. Since 1/14) Test Run Once the power feeder assembly is complete and mounted on the table, you must test run your power feeder to make sure it runs properly. If, during the test run, you cannot easily locate the source of an unusual noise or vibration, stop using the power feeder immediately, then review the Troubleshooting table on Page 23. If you still cannot remedy a problem, contact our Technical Support at (360) 734-3482 for assistance.
Model W1764 (For Machines Mfg. Since 1/14) OPERATIONS General This machine will perform many types of operations that are beyond the scope of this manual. Many operations can be dangerous or deadly if performed incorrectly. The instructions in this section are written with the understanding that the operator has the necessary knowledge and skills to operate this machine.
Model W1764 (For Machines Mfg. Since 1/14) Power Feeder Accessories The following power feeder accessories may be available through your local Woodstock International Inc. Dealer. If you do not have a dealer in your area, these products are also available through online dealers. Please call or e-mail Woodstock International Inc. Customer Service to get a current listing of dealers at: 1-800-840-8420 or at sales@woodstockint.com.
Model W1764 (For Machines Mfg. Since 1/14) MAINTENANCE General Regular periodic maintenance on your machine will ensure its optimum performance. Make a habit of inspecting your machine each time you use it. Check for the following conditions and repair or replace when necessary: • • • Loose mounting bolts and damaged wheel rubber. Worn or damaged, switch, cord, and plug. Any other condition that could hamper the safe operation of the power feeder.
Model W1764 (For Machines Mfg. Since 1/14) SERVICE General This section covers the most common service adjustments or procedures that may need to be made during the life of your machine. If you require additional machine service not included in this section, please contact Woodstock International Technical Support at (360) 734-3482 or send e-mail to: tech-support@shopfox.biz. Wheel Replacement If you damage one or more wheels, you can easily replace the wheels.
Model W1764 (For Machines Mfg. Since 1/14) Troubleshooting This section covers the most common problems and corrections with this type of machine. WARNING! DO NOT make any adjustments until power is disconnected and moving parts have come to a complete stop! PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Motor will not start. 1. Low voltage. 2. Open circuit in motor or loose connections. 3. Blown fuse. 4. Motor brushes are at fault. 5. Motor switch or motor is at fault. 1.
Model W1764 (For Machines Mfg. Since 1/14) Wiring Diagram 120 VAC 5-15 Plug Neutral Hot Fuse 3.15A Ground 250VAC Motor Speed Dial Ground SHOCK HAZARD! Disconnect power before servicing electrical parts. Touching electrified parts will result in severe burns, electrocution, or death. Power Feed Direction Switch Motor PC Board Universal Brush Type Motor WIRING DIAGRAM COLOR KEY The photos and diagrams included in this section are best viewed in color. You can view these pages in color at www.
89 62 34 51 31 17 49 85 34 7 33 89 29 17 17 85 36 20 25 8 53 33 68 29 17 17 28 22 38 86V2 45 54 30 28 83 23 51 49 38 56 58 71 20 15 83 51 8 36 30 14 20 50 69 54 8 14 69 9 14 20 53 83 56 1 11 615 9 14 14 79 69 67 77 74 6 11 8 54 79 6 8 16 15 23 60 63 82 59 57 6 70 46 67 56 89 6 83 36 11 90 53 6 66 74 83 23 16 820 82 50 47 60 72 63 58 57 59 66 62 4970 45 86 47 46 67 38-1 72 38-2 39-2 62 39-1 88 71 61 38-1
PARTS Model W1764 (For Machines Mfg. Since 1/14) REF PART # 1 6 7 8 9 11 12 14 15 16 17 19 20 22 23 25 28 29 30 31 33 34 36 36-1 37 38 38-1 38-2 39 39-1 39-2 39-3 39-4 39-5 40 40-1 43 45 X1764001 EXTRA ROLLER X1764006 SPROCKET CASE X1764007 TORTION SPRING 30 X 3 X1764008 BUSHING X1764009 CASE CAP X1764011 GEARKIT(25T) X1764012 EXT RETAINING RING 22MM X1764014 DRIVE SHAFT X1764015 GEAR 10-TEETH X1764016 E-CLIP 6.4MM X1764017 EXT RETAINING RING 12MM X1764019 SHAFT X1764020 HEX NUT M8-1.
CUT ALONG DOTTED LINE Model W1764 (For Machines Mfg.
Fold along dotted lIne place stamp Here Woodstock international inc. p.o.
WARRANTY WARRANTY Woodstock International, Inc. warrants all Shop Fox machinery to be free of defects from workmanship and materials for a period of two years from the date of original purchase by the original owner. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or accidents, lack of maintenance, or reimbursement of third party expenses incurred. Woodstock International, Inc.
High Quality Machines and Tools Woodstock International, Inc. carries thousands of products designed to meet the needs of today's woodworkers and metalworkers.
