MODEL W1668 13 ⁄ 4" Oscillating Drill Press 1 OWNER'S MANUAL Phone: (360) 734-3482 • Online Technical Support: tech-support@shopfox.biz COPYRIGHT ©2000 BY WOODSTOCK INTERNATIONAL, INC. REVISED APRIL, 2008 (BL) #4725CR WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
K_`j dXelXc gifm`[\j Zi`k`ZXc jX]\kp `ejkilZk`fej fe k_\ gifg\i j\klg# fg\iXk`fe# dX`ek\eXeZ\ Xe[ j\im`Z\ f] k_`j dXZ_`e\&\hl`gd\ek% =X`cli\ kf i\X[# le[\ijkXe[ Xe[ ]fccfn k_\ `ejkilZk`fej ^`m\e `e k_`j dXelXc dXp i\jlck `e j\i`flj g\ijfeXc `ealip# `eZcl[`e^ XdglkXk`fe# \c\ZkifZlk`fe fi [\Xk_% K_\ fne\i f] k_`j dXZ_`e\&\hl`gd\ek `j jfc\cp i\jgfej`Yc\ ]fi `kj jX]\ lj\% K_`j i\jgfej`Y`c`kp `eZcl[\j Ylk `j efk c`d`k\[ kf gifg\i `ejkXccX$ k`fe `e X jX]\ \em`ifed\ek# g\ijfee\c kiX`e`e^ Xe[ ljX^\ Xlk_fi`qX$
SAFETY................................................4 Standard Safety Instructions.................... 4 Additional Safety for Drill Presses.............. 6 Avoiding Potential Injuries....................... 7 PARTS............................................... 32 W1668 Parts Breakdown ....................... 32 Parts List.......................................... 33 Warranty Registration.......................... 35 WARRANTY.........................................
INTRODUCTION W1668 131⁄4" Oscillating Drill Press INTRODUCTION Woodstock Technical Support This machine has been specially designed to provide many years of trouble-free service. Close attention to detail, ruggedly built parts and a rigid quality control program assure safe and reliable operation. Woodstock International, Inc. is committed to customer satisfaction. Our intent with this manual is to include the basic information for safety, setup, operation, maintenance, and service of this product.
Specifications Motor Type:.................................................. TEFC Capacitor Start Induction Motor:............................................3⁄4 HP, 110V, 9 Amp., Single Phase ⁄ 60 Hz RPM:........................................................................................... 1725 Power Transfer:..................................................................... V-Belt Drive Bearings:................................................ Shielded & Lubricated Ball Bearings Switch:...........
W1668 131⁄4" Oscillating Drill Press SAFETY J8= D8:?@E<% =8@CLI< KF =FCCFN @EJKIL:K@FEJ 9
W1668 131⁄4" Oscillating Drill Press ('% E% Klie gfn\i F== Xe[ Xccfn Xcc dfm`e^ gXikj kf Zfd\ kf X Zfdgc\k\ jkfg Y\]fi\ c\Xm`e^ dXZ_`e\ leXkk\e[\[% ((% ;F EFK LJ< @E ;8E>IFLE;<; <% Le[\ij`q\[ Zfi[j fm\i$ _\Xk Xe[ cfj\ gfn\i% I\gcXZ\ \ok\ej`fe Zfi[j `] k_\p Y\Zfd\ [XdX^\[% ;F EFK lj\ \ok\ej`fe Zfi[j
W1668 131⁄4" Oscillating Drill Press Additional Safety for Drill Presses SAFETY READ and understand this entire instruction manual before using this machine. Serious personal injury may occur if safety and operational information is not understood and followed. DO NOT risk your safety by not reading! Use this and other machinery with caution and respect. Always consider safety first, as it applies to your individual working conditions.
W1668 131⁄4" Oscillating Drill Press Avoiding Potential Injuries SAFETY Figure 3. Keep fingers away from spinning drill bits, cutters, and sanding surfaces. Figure 1. Never drill while holding the workpiece by hand. Figure 4. Remove handles when using the oscillating sanding feature. Figure 2. Remove switch safety key when not in use.
W1668 131⁄4" Oscillating Drill Press ELECTRICAL ELECTRICAL The machine must be properly set up before it is safe to operate. DO NOT connect this machine to the power source until instructed to do so in the "Test Run" portion of this manual. 110V Operation The Model W1668 is wired for 110V operation. We recommend connecting this machine to a dedicated circuit with a verified ground, using the circuit size below as a minium.
W1668 131⁄4" Oscillating Drill Press SETUP Unpacking This machine has been carefully packaged for safe transportation. If you notice the machine has been damaged during shipping, please contact your authorized Shop Fox dealer immediately. Inventory The following is a description of the main components shipped with the Model W1668. Lay the components out to inventory them. Keep machine disconnected from power until instructed otherwise.
W1668 131⁄4" Oscillating Drill Press Base and Column The base and column must be securely mounted, so the machine will not fall over. To install the base and column, do these steps: 1. Position the drill press base on a flat and stable surface. 2. Using two clamps, clamp the base to the mounting surface. 3. Use the holes provided in the bottom of the base as a drill guide, and drill holes in the mounting surface (see Figure 8). SETUP 4.
W1668 131⁄4" Oscillating Drill Press Table Support When secured to the column, the table support supports the table, provides smooth table height adjustment, and locks in position with firm lever torque. Additionally, when the table is rotated, the rack will slide with the table support. 12mm Lock Handle To install the table support, do these steps: 1.
W1668 131⁄4" Oscillating Drill Press 6. Position the rack so the long un-toothed end is facing upward (see Figure 13). 7. Insert the rack into the table support bracket so the teeth face out and mesh with the pinion (see Figure 13). 8. While holding the rack in place, slide the table support bracket onto the column. 9. Allow the bracket and rack to slide down until the bottom of the rack bevel slips into the tapered shoulder on the column support.
W1668 131⁄4" Oscillating Drill Press Headstock The headstock must be tightened in position with two set screws, so the headstock is aligned with the drill press foot for balance and weight distribution. DO NOT over tighten the set screws and strip the threads or bend the column. Belt Cover Knob GET assistance before beginning the next step. The headstock is an awkward and heavy load. To install the headstock, do these steps: 1. Figure 16. Aligning the pocket in the headstock with the column.
W1668 131⁄4" Oscillating Drill Press Drill Chuck The drill chuck is seated to the spindle with a JT-33 tapered surface and a screw. To install the drill chuck, do these steps: 1. Clean the drill chuck and spindle with mineral spirits and follow all safety warnings on the container. Failure to clean the tapered-mating surfaces of the spindle and drill chuck will result in the chuck falling off during use. 2.
W1668 131⁄4" Oscillating Drill Press ADJUSTMENTS Belt Tension Motor Lock Screw The drill press main drive belts last a long time; however, during machine life, a belt may stretch slightly which can cause the pulleys to slip under a load. You will then need to adjust the motor-to-idler pulley belt tension to compensate for this normal stretching. NOTE: The spindle-to-idler pulley belt automatically adjusts to the correct tension when the motor-to-idler pulley belt tension is adjusted.
W1668 131⁄4" Oscillating Drill Press Feed Shaft Spring Tension The feed shaft return spring is adjusted at the factory; however, during the life of the drill press you may want to adjust the feed shaft return spring to a stronger return pressure. Cover Nut MAKE SURE your machine is unplugged during all assembly, adjustments, or maintenance procedures. Otherwise serious personal injury may occur! Jam Nut Spring Lock Cover Figure 24. Typical feed shaft return spring assy.
W1668 131⁄4" Oscillating Drill Press 7. Engage the next available spring-cover lock slot with the locking lug, and hold the spring lock cover tightly against the side of the headstock (see Figure 27). Cover Nut 8. Snug the cover nut against the spring cover just until the nut stops, and then back-off the nut approximately 1⁄3 turn, or just enough so there is no binding anywhere along complete spindle travel. 9. Hold the cover nut and tighten the jam nut against the cover nut (see Figure 27).
W1668 131⁄4" Oscillating Drill Press Table Height and Tilt You can adjust the table height and tilt to accommodate for workpiece height or achieve special drilling/sanding angles. You can also move the table out of the way and use the drill press base as a table for drilling/sanding. ADJUSTMENTS To adjust the table, do these steps: 1. Loosen the table lock lever. 2. Turn the hand crank to raise or lower the table, as shown in Figure 30. 3.
W1668 131⁄4" Oscillating Drill Press Drilling Speed The Model W1668 13 1⁄4'' Oscillating Drill Press has 12 speeds ranging from 250 to 3050 RPM. Refer to the speed charts located under the belt guard while following the instructions below. Motor Lock Screw UNPLUG the drill press before changing speeds to avoid accidental start up. Failure to do this may result in serious personal injury. Push Rod To change the drilling speed, do these steps: Figure 33. Loosening the lock knob. 1.
W1668 131⁄4" Oscillating Drill Press Drill Press RPM Chart Use Figure 35 to select the optimum motor-to-spindle pulley ratio for drilling, cutting, and sanding operations. The belt setting in the example in Figure 36 shows the spindle belt in the #1 spindle pulley position and the motor belt in the #7 motor pulley location. This will produce a speed of 1,870 RPM. Refer to the Drill, Cutter, and Saw RPM Chart on Page 21 for suggested tool RPMs. Figure 36. Drill Press RPM Chart.
W1668 131⁄4" Oscillating Drill Press ADJUSTMENTS -21-
ADJUSTMENTS W1668 131⁄4" Oscillating Drill Press -22-
W1668 131⁄4" Oscillating Drill Press OPERATIONS Starting the Drill Press Once assembly is complete and adjustments are done to your satisfaction, you are ready to start the drill press. Every time you start the drill press, you should follow these basic instructions. Keep your shop “Child Safe.” Always remove the switch safety key when drill press is not in use. Serious injury may occur. WEAR safety glasses and a respirator during drilling or sanding operations.
W1668 131⁄4" Oscillating Drill Press Drill/Drum Changes NEVER troubleshoot or adjust the machine while it is running. Wait until the machine is turned off, unplugged and all working parts have come to a stop before proceeding! To change drill bits and sanding drums, do these steps: 1. UNPLUG THE DRILL PRESS! 2. Use the chuck key to open the chuck wide enough to accept the new bit or the sanding drum mandrel (see Figure 40). Figure 40. Installing bit. 3.
W1668 131⁄4" Oscillating Drill Press Using the Oscillator One of the great features of the Model W1668 13 1⁄4'' Oscillating Drill Press is its sanding capability. The drill press can be converted from drilling operations to sanding operations in just a few steps. UNPLUG the machine and remove all handles before using the oscillating feature. The handles swing during operation. Belt and storage bracket To use the oscillating feature, do these steps: Figure 43. Oscillator belt on storage bracket. 1.
W1668 131⁄4" Oscillating Drill Press 7. Remove the mandrel nut from the mandrel. 8. Install the sanding drum, sandpaper, and top and bottom mandrel washers on the mandrel, then secure with the mandrel nut, as shown in Figure 46. Insert Bottom Mandrel Washer 9. Choose the insert that has an opening which is slightly bigger than the sanding drum chosen (see Figure 46). • For general drill bits, small reamers, and miscellaneous small cutting and sanding bits, use the 5⁄8'' and the 1'' table inserts.
W1668 131⁄4" Oscillating Drill Press MAINTENANCE Table and Base General Keep the table and other unpainted surfaces rust-free with regular applications of products like Boeshield® T-9. For long term storage consider products like Kleen Bore's Rust Guardit™. Periodic maintenance on your Model W1668 131⁄4'' Oscillating Drill Press will ensure its optimum performance. Make a habit of inspecting your drill press after each use. Sanding Sleeves NEVER adjust or service the machine while it is running.
W1668 131⁄4" Oscillating Drill Press Troubleshooting MAINTENANCE Use this table to isolate and correct any problems with your drill press. If you cannot correct a problem, contact Woodstock International, Inc. at 1-360-734-3482 or tech-support@shopfox.biz.
W1668 131⁄4" Oscillating Drill Press Wiring Diagram MAINTENANCE -29-
W1668 131⁄4" Oscillating Drill Press Drill Press Accessories The following drill press accessories may be available through your local Woodstock International Inc. Dealer. If you do not have a dealer in your area, these products are also available through online dealers. Please call or e-mail Woodstock International Inc. Customer Service to get a current listing of dealers at: 1-800-545-8420 or at sales@woodstockint.com. Sanding Sleeves are sized to fit the D2677 Drum Sander Set.
W1668 131⁄4" Oscillating Drill Press The SHOP FOX® D2056 Tool Table is great for bench-top tools like chop saws, drill presses, planers, scroll saws and bandsaws. Support cross braces on top provide incredible strength and capacity. Flared legs and adjustable rubber feet ensure stability and reduce machine vibration. Butcher block finish table top measures 13" x 23" and is 301⁄2" tall with a 700 lb. capacity. D2251 Steelex® Adjustable Circle Cutter cuts flat-sided holes in wood from 1" to 5".
W1668 131⁄4" Oscillating Drill Press PARTS W1668 Parts Breakdown PARTS 7A -32-
W1668 131⁄4" Oscillating Drill Press Parts List DESCRIPTION REF PART # DESCRIPTION BASE COLUMN COLUMN & COLUMN FLANGE ASSEMBLY HEX BOLT M10-1.5 X 25 RACK V2.06.06 COLUMN RING SET SCREW M6-1.0 X 10 TABLE V2.05.03 WORM PINION CLAMP BOLT M12-1.75 X 50 WORM GEAR LIFT HANDLE SET SCREW M6-1.0 X 10 CLAMP BOLT M10-1.5 X 30 DUST PORT PHLP HD SCR M4-.7 X 22 HEAD CASTING HEX NUT M10-1.5 SPRING COVER RETURN SPRING SPRING WASHER BUSHING HEX NUT M10-1.5 SPECIAL SET SCREW FEED SHAFT DEPTH COLLAR V1.08.
W1668 131⁄4" Oscillating Drill Press REF PART # DESCRIPTION REF PART # DESCRIPTION 103 104 105 106 107 108 114 115 116 117 118 135 139 140 TABLE INSERT 1" I.D. TABLE INSERT 1 3/8" I.D. TABLE INSERT 1 7/8" I.D. LONG HAIR SAFETY LABEL GLASSES SAFETY LABEL SHOP FOX LABEL DEPTH STOP BRACKET FLAT WASHER 5MM CAP SCREW M5-0.8 X 12 DEPTH STOP MOUNT CAP SCREW M8-1.
Warranty Registration Name____________________________________________________________________________________ Street___________________________________________________________________________________ City__________________________ State____________________________Zip_________________________ Phone #_______________________ Email___________________________Invoice #____________________ Model #_________Serial #______________Dealer Name__________________Purchase Date___________ The following information is give
FOLD ALONG DOTTED LINE Place Stamp Here Woodstock international inc. p.o.
N8II8EKP Nff[jkfZb @ek\ieXk`feXc# @eZ% nXiiXekj Xcc J_fg =fo dXZ_`e\ip kf Y\ ]i\\ f] [\]\Zkj ]ifd nfibdXej_`g Xe[ dXk\i`Xcj ]fi X g\i`f[ f] knf p\Xij ]ifd k_\ [Xk\ f] fi`^`eXc gliZ_Xj\ Yp k_\ fi`^`eXc fne\i% K_`j nXiiXekp [f\j efk Xggcp kf [\]\Zkj [l\ [`i\Zkcp fi `e[`i\Zkcp kf d`jlj\# XYlj\# e\^c`^\eZ\ fi XZZ`[\ekj# cXZb f] dX`ek\eXeZ\# fi i\`dYlij\d\ek f] k_`i[ gXikp \og\ej\j `eZlii\[% Nff[jkfZb @ek\ieXk`feXc# @eZ% n`cc i\gX`i fi i\gcXZ\# Xk `kj \og\ej\ Xe[ Xk `kj fgk`fe# k_\ J_fg =fo dXZ_`e\ fi dXZ_`
