International, Inc. Nail Gun User Manual

ManualsBrandsWoodstock ManualsNail GunW1774

Phone: (360) 734-3482 • Online Technical Support: tech-support@shopfox.biz

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT

THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.

#9551TS Printed in China

MODEL W1774

18 GAUGE BRAD NAILER

OWNER'S MANUAL

Summary of content (20 pages)

PAGE 1
MODEL W1774 18 GAUGE BRAD NAILER OWNER'S MANUAL Phone: (360) 734-3482 • Online Technical Support: tech-support@shopfox.biz COPYRIGHT © JUNE, 2007 BY WOODSTOCK INTERNATIONAL, INC., REVISED DECEMBER, 2007 (JM) WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
PAGE 2
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/equipment. Failure to read, understand, and follow the instructions given in this manual may result in serious personal injury, including amputation, electrocution, or death. The owner of this machine/equipment is solely responsible for its safe use.
PAGE 3
Model W1774 18 Gauge Brad Nailer SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below.
PAGE 4
Model W1774 18 Gauge Brad Nailer Safety Instructions for Pneumatic Tools 10. USE PROPER AIR HOSE for the tool. Make sure your air hose is in good condition and is long enough to reach your work without stretching. 17. DISCONNECT TOOLS before servicing, changing accessories, or moving to another location. 11. WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Non-slip footwear is recommended.
PAGE 5
Model W1774 18 Gauge Brad Nailer Additional Safety for Nailers/Staplers 1. HAND INJURIES: Do not place your hands near the nail point of entry. A nail can deflect and tear through the surface of the workpiece, puncturing your hand or fingers. 5. HOSE USAGE: Make sure your air hose is designed for the tool in use, is in good condition, and is long enough to reach your work without stretching. However, an overly long air hose in the work area may be a tripping hazard. 2.
PAGE 6
Model W1774 18 Gauge Brad Nailer INTRODUCTION Woodstock Technical Support Machine Data Nail Size ............................. 18 Gauge Nail Length.............................. 5⁄8"–2" Magazine Capacity ................. 100 Nails Air Inlet................................ 1⁄4" NPT Weight .................................31⁄2 lbs. Operating Pressure ............... 60–100 PSI This Model W1774 18 Gauge Brad Nailer has been specially designed to provide many years of trouble-free service.
PAGE 7
Model W1774 18 Gauge Brad Nailer Compressed Air System The Model W1774 is designed to be operated at 60-100 PSI using clean, dry, regulated, compressed air. Do not exceed the 120 PSI maximum operating pressure for your model. Before using your nailer, regulate the air pressure to find the optimum setting within the specified operating range. Start by testing the nailer at a low setting, then increase the air pressure as needed for satisfactory results.
PAGE 8
Model W1774 18 Gauge Brad Nailer SETUP Unpacking This brad nailer has been carefully packaged for safe transportation. If you notice the tool has been damaged during shipping, please contact your authorized Shop Fox dealer immediately. Inventory The following is a description of the main components shipped with the Model W1774. Lay the components out to inventory them. Note: If you can't find an item on this list, check the mounting location on the tool or examine the packaging materials carefully.
PAGE 9
Safety Nose Model W1774 18 Gauge Brad Nailer Safety Nose Mechanism — If the nailer fires when the trigger is pulled, without the safety nose mechanism being depressed, then the nailer is not working properly. A safety mechanism on the nose of the nailer protects against accidental firing. When the trigger is pressed, the nailer will not fire until the safety nose mechanism is depressed.
PAGE 10
Model W1774 18 Gauge Brad Nailer OPERATIONS Loading When replacing nails in your Model W1774, follow these guidelines: Gauge: ........................................18 Length: .................................. 5⁄8"–2" Capacity: ................................... 100 To load your nailer, do these steps: Figure 3. Loading nails into magazine. 1. DISCONNECT NAILER FROM THE AIR SUPPLY! 5. Slide the nails all the way down to the nose of the nailer. 2. Depress the magazine latch, as shown in Figure 2. 6.
PAGE 11
Model W1774 18 Gauge Brad Nailer 3. Depress the safety nose mechanism against your workpiece. 5. Pull the trigger. — If the nail drove into the wood far enough, continue with your intended operations. 4. Before pulling the trigger, make sure your free hand and other body parts are positioned out of the way of a potential path of a nail in case of deflection. — If the nail either went too far or not far enough, then adjust the air pressure.
PAGE 12
Model W1774 18 Gauge Brad Nailer Clearing Jammed Nails �� A jammed nail must be cleared before using the nailer again. �� To clear a jammed nail from the discharge area, do these steps: 1. DISCONNECT NAILER FROM THE AIR SUPPLY! Figure 5. Removing guide cover. 2. Depress the magazine latch and pull back the magazine cover until it stops. 5. The jammed nail should now be visible; remove it with needle nose pliers. 3. Remove the nail stick from the magazine. 6.
PAGE 13
Model W1774 18 Gauge Brad Nailer Replacing Pistons/ O-Rings 6. Open the nose cover as if to clear a jammed nail. Under heavy use, a piston or piston shaft may wear out. Replacement is quick and easy. Contact your authorized Shop Fox dealer to obtain the Piston Repair Kit (Part Number X1774068) or the complete O-Ring Repair Kit (Part Number X1774069). 7. Watch the discharge area and push the top of the piston with your finger. You will see the piston shaft slide down the discharge area. 8.
PAGE 14
Model W1774 18 Gauge Brad Nailer CLEANING & LUBRICATION Cleaning Lubricating Use a good solvent to clean the nose assembly of the nailer. Always be sure that the nailer is dry before using it again. Use a quality pneumatic tool oil with your new Shop Fox nailer to help maintain its useful life. Place two to six drops of oil in the nailer air inlet (as shown in Figure 6) before every use, or after 2 hours of continuous use. Wipe off any excess oil near the nailer exhaust to avoid dust build-up.
PAGE 15
-13- �� Model W1774 18 Gauge Brad Nailer W1774 PARTS BREAKDOWN
PAGE 16
Model W1774 18 Gauge Brad Nailer W1774 PARTS LIST REF PART�# DESCRIPTION REF PART�# DESCRIPTION 101 X1774101 SPECIAL�BOLT 136 X1774136 COMPRESSION�SPRING 102 X1774102 EXHAUST�PORT 137 X1774137 SAFETY�NOSE 103 X1774103 COMPRESSION�SPRING 138 X1774138 DRIVER�GUIDE 104 XPB42M HEX�BOLT�M5-.8�X�20 139 X1774139 SPACER 105 XPLW01M LOCK�WASHER�5MM 140 XPSB15M CAP�SCREW�M5-.8�X�20 106 X1774106 CYLINDER�CAP 141 XPSB23M CAP�SCREW�M4-.7�X�12 107 X1774107 O-RING�13.7�X�2.
PAGE 17
Model W1774 18 Gauge Brad Nailer Troubleshooting Symptom Possible Cause Possible Solution Air leaking at trigger valve area. 1. O-rings in trigger valve housing are damaged. 1. O-rings must be replaced & operation of safety nose must be checked. Air leaking between 1. Loose screws in housing. housing and hose 2. Damaged O-ring. 3. Loose air fitting. 1. Tighten screws. 2. Replace O-ring 3. Tighten air fitting & use teflon tape. Air leaking between 1. Damaged seal. housing and cap. 1.
PAGE 18
��
PAGE 19
Warranty Registration Name ___________________________________________________________________________________ Street __________________________________________________________________________________ City _________________________ State ___________________________Zip ________________________ Phone # ______________________ Email __________________________Invoice # ___________________ Model #_________Serial #______________Dealer Name__________________Purchase Date___________ CUT ALONG DOTTED LINE The follo
PAGE 20
FOLD ALONG DOTTED LINE Place Stamp Here WOODSTOCK INTERNATIONAL INC. P.O.