User Manual

21 22
Installing the Custom-Shape Wireless Dog Fence
Setting Up the Collar(s) Setting Up the Collar(s)
Havahart
®
Custom-Shape Wireless Dog Fence
www.HavahartWireless.com
Havahart
®
Custom-Shape Wireless Dog Fence
1-800-800-1819, Option 1
Setting Up the Collar(s)
4
Screen 6.4
Screen 6.5
Screen 6.2
Screen 6.3
The Collar should not be placed on your
dog until after you have successfully
installed it on the system.
!
IMPORTANT MESSAGE
Installing a Battery:
1. Make sure a Battery is fully charged before installing it in the Collar
(see Recharging a Battery on Page 25). Turn the Battery Cap on the
Collar counterclockwise about 1/4 turn and pull it out. With the
positive side facing outward, install one rechargeable RCR123 Battery
into the Collar (see Figure 5.0). Replace the Battery Cap and turn it
clockwise to lock it in place.
2. The Collar will flash green. If it does not, shake the Collar gently as the
Collar is in sleep mode (see the Havahart
®
Wireless Collar Light Chart
on Page 25).
NOTE : The Collar is always “on” when a fully charged Battery is
installed. However, the Collar may be awake or asleep based on
Integrated Motion Sensor Technology. This technology allows
the Collar to conserve Battery life when appropriate by putting
the Collar to sleep. The Collar Light will not flash when the Collar
is asleep. Movement, such as gently shaking the Collar, will
awaken it and the Collar Light will flash green (see the Havahart
®
Wireless Collar Light Chart on Page 25). The Collar Light will flash
red to indicate that the Battery needs to be recharged. The
Controller will also produce an auditory tone to alert you that
the Battery is low.
+
-
RCR123
Figure 5.0
Screen 7.5
Screen 7.6
Naming a Collar:
You can name each Collar using the Controller.
1. Select “Collars” from the main menu (see Screen 6.2).
2. Press “Name Collar” (see Screen 7.3).
3. Press the Collar you would like to name (see Screen 7.4).
4. Create the name of the Collar. Press the left or right arrows to
highlight the letter you would like to change. Then press the up
or down arrows to choose the character that you want from A-Z
and 0-9. The name can be up to 8 characters in length. Repeat
this process for each letter until you are satisfied with the name.
You can also change the name of a Collar back to its default
name by pressing the “DEFAULT NAME” Button in the lower
center of the screen (see Screen 7.5).
5. Once you are satisfied with the name of the Collar, press
“SAVE” and a confirmation will display briefly and then
take you back to Collar Options (see Screen 7.6).
Screen 7.3
Screen 7.4
Embedded Antennas
Collar Light
Grey Battery Housing
Battery Cap
Probes
Washers
D
E
F
A
B
C
C
Collar Features:
E
F
D
A
A
B
Activating a Collar:
The system allows you to activate up to 2 Collars using the Controller.
Before initiating the setup process, make sure to install a fully charged
RCR123 Battery in the Collar.
1. Position the Collar near the Master Base A.
2. Select “Collars” from the main menu (see Screen 6.2).
3. Select “Add Collar” (see Screen 6.3).
4. Press “Next” (see Screen 6.4).
5. While gently shaking a Collar to keep it awake, press the Collar that
you would like to activate (see Screen 6.5).
If successful, a Congratulatory screen will appear (see Screen 6.7),
indicating that the Collar has been properly set. You may proceed
to name your Collar. If you choose not to name it, the Collar will be
given the default name of COLLAR1 or COLLAR2 (see the “Naming
a Collar” section for more information). If unsuccessful, you will be
directed to try again (see Error Screen 1.2).
Error Screen 1.2
Screen 6.7
Once you have a Collar activated, test your
fence boundary and or Exclusion Zone(s) in
different locations.
!
IMPORTANT MESSAGE