User's Manual

Test Screen Code

To test the Screen ON/OFF commands the AVR21ENR1 remote must be configured for HT

MASTER ON/OFF ENABLED.

Press and hold the REM MENU Button [oval 36] on the remote until the Set Button [oval 18]

lights red. Press the ▲ Navigation Button [oval 16] TWICE so HT MASTER ON/OFF shows in

the remote’s LCD Information Display. Press the Set Button [oval 18]. Press the ▼/▲

Navigation Button [oval 16] until ENABLED appears in the display. Press the Set Button [oval

18]. SAVING will appear briefly in the remote display and then SAVED will flash four times. The

HT MASTER ENABLED configuration is now set and the remote will automatically return to

operational mode.

Press the TV Button [oval 6] on the remote. TV should appear in the remote display. Press the

ON Button [oval 2] on the remote. The Screen just configured should turn ON or drop. Press the

OFF Button [oval 1] on the remote. The Screen should turn OFF or retract. NOTE: If the Screen

does not respond, be sure an IR emitter is properly connected to the Control Out All Jack

[circle 35] on the AVR rear panel and properly attached to the Screen.

To return to normal operation mode press the AVR Button [oval 5] on the AVR21ENR1 remote.

Voltage Trigger (Screen)

The Trigger Out [circle 38] on the AVR rear panel can be controlled in two modes:

AVR ON/OFF: Simply put, when the AVR turns ON, the Trigger Out [circle 38] outputs a

constant +12VDC control voltage. In this case with the Trigger Out [circle 38] being used to

drop a screen, the screen will drop as soon as the AVR is turned ON. When the AVR is turned

OFF, the Trigger Out [circle 38] drops to 0 VDC, and the screen retracts. NOTE: If the AVR

turns on to Multiroom Mode, the Trigger Out [circle 38] will stay at 0VDC until the Main Room is

turned ON.

MANUAL VIA REMOTE: In this mode, the Trigger Out Jack [circle 38] is controlled with the

Trigger Button [oval 50] on the AVR21ENR1 remote. When the AVR is turned ON, the Trigger

Out has an output of 0VDC. When the Trigger Button [oval 50] on the remote is pressed, the

Trigger Out goes to +12VDC, in this case to drop a screen. Press the Trigger Button [oval 50]

again, the voltage is cut and the screen retracts.

To configure the AVR21EN Trigger Out Jack [circle 38] to drop a projection screen when the

Main Room is turned ON:

Press the Menu Button on the remote to bring the MAIN MENU to the screen. Press the ▼/▲

Navigation Button [oval 16] so that the cursor is pointed to the REMOTE CONTROL SETUP

line.

Press the Set Button [oval 18]. The REMOTE CNTL SETUP 1 screen will appear. Press the

▼/▲ Navigation Button [oval 16] so that the cursor is pointed to GO TO REMOTE CNTL 2.

Press the Set Button [oval 18]. The REMOTE CNTL SETUP 2 screen will appear.

Press the ▼/▲ Navigation Button [oval 16] so that the cursor is pointed to the ASSIGN

TRIGGER OUT line. Press the ◄/► Navigation Button [oval 16] until SCRN appears. Press the

▼/▲ Navigation Button [oval 16] so that the cursor is pointed to SCREEN CONTROL. Press the

Set Button [oval 18]. Press the ▼/▲ Navigation Button [oval 16] so that the cursor is pointed

to the CONTROL line. Press the ◄/► Navigation Button [oval 16] to select the preferred mode.

Press ▼/▲ Navigation Button [oval 16] so that the cursor is pointed to the BACK TO REM

CNTL SETUP line. Press the Set Button [oval 18].

To test the SCREEN UP/DOWN commands with AVR ON/OFF, turn the AVR OFF and manually

raise the screen. To test ON, either: press the Standby/ON Button [square 2] on the AVR front