User's Manual

To configure the AVR21EN Trigger Out Jack [circle 38] to control Lighting when the Main Room

is turned ON:

Press the Menu Button [oval 44] on the remote to bring the MAIN MENU to the screen. Press

the ▼/▲ Navigation Button [oval 16] so that the cursor is pointed to the REMOTE CONTROL

SETUP line. Press the Set Button [oval 18]. The REMOTE CNTL SETUP 1 screen will appear.

Press the ▼/▲ Navigation Button [oval 16] so that the cursor is pointed to GO TO REMOTE

CNTL 2. Press the Set Button [oval 18]. The REMOTE CNTL SETUP 2 screen will appear.

Press the ▼/▲ Navigation Button [oval 16] so that the cursor is pointed to the ASSIGN

TRIGGER OUT line. Press the ◄/► Navigation Button [oval 16] until LGHT appears. Press the

▼/▲ Navigation Button [oval 16] so that the cursor is pointed to LIGHTING CONTROL. Press

the Set Button [oval 18]. Press the ▼/▲ Navigation Button [oval 16] so that the cursor is

pointed to the CONTROL line. Press the ◄/► Navigation Button [oval 16] to select the preferred

mode. Press ▼/▲ Navigation Button [oval 16] so that the cursor is pointed to the BACK TO

REM CNTL SETUP line. Press the Set Button [oval 18].

To test the Lighting ON/OFF commands with AVR ON/OFF, turn the AVR OFF and manually turn

the lights OFF. To test ON, either: press the Standby/ON Button [square 2]

on the AVR front

panel; or press the ON Button [oval 2] on the AVR21ENR1 remote. The AVR should turn ON

and the lights should turn ON or change scenes.

To test OFF, either: press the Standby/ON Button [square 2] on the AVR front panel; or: press

the OFF Button [oval 1] on the AVR21ENR1 remote. The AVR should turn OFF and the lights

should turn OFF or change scenes.

To test the LIGHTING commands with MANUAL VIA REMOTE, turn the AVR OFF and manually

turn the lights OFF. Turn the AVR ON by pressing the Standby/ON Button [square 2] on the

AVR front panel or press the ON Button [oval 2] on the remote. (The AVR should be on, but the

Lights should still be OFF.) Press the Trigger Button [oval 50] on the remote. The lights should

turn ON or change scene. Press the Trigger Button [oval 50] again and the lights should turn

OFF or change scenes.

Exit Setup

If no further programming is required, press the AVR Button [oval 5] on the AVR21ENR1 remote

and then the Exit Button [oval 17] to return to normal operation mode.

CURTAIN CONTROL

To open and close a curtain with the AVR turn on/turn off functions, press the Menu Button [oval

44] on the remote to bring the MAIN MENU to the screen. Press the ▼/▲ Navigation Button

[oval 16] so that the cursor is pointed to the REMOTE CONTROL SETUP line. Press the Set

Button [oval 18]. The REMOTE CNTL SETUP 1 screen will appear. Press the ▼/▲ Navigation

Button [oval 16] so that the cursor is pointed to GO TO REMOTE CNTL 2. Press the Set

Button [oval 18]. The REMOTE CNTL SETUP 2 screen will appear. Press the ▼/▲ Navigation

Button [oval 16] so that the cursor is pointed to the CURTAIN CONTROL line. Press the Set

Button [oval 18]. The CURTAIN CONTROL SETUP screen will appear.

Carrier

With the cursor positioned next to CARRIER, press the ◄/► Navigation Button [oval 16] to

select the proper setting. NOTE: Most IR remotes used with common source components will

have a carrier, so YES should be selected as a first test. Some Cable Box remotes do not use a

carrier, so if a code setting doesn’t work, try changing this setting.