MODEL WSP-i450 (4inch Industrial Printer) Rev. 1.0 WOOSIM SYSTEMS Inc. #501, Daerung Technotown 3th, 448, Gasan-Dong, GeumChun-Ku, Seoul, Korea Tel : +82-2-2107-3700 Fax : +82-2-2107-3707 URL: http://www.woosim.com http://www.woosim.
WSP-i450 Rev. 1.0 Copyright WSP-i450 4inch Industrial printer operator’s manual. Copyright ⓒ2009 by Woosim Systems Inc. All rights reserved. The information contained in this manual is the property of Woosim Systems Inc. and may not be reproduced in whole or in part without the prior written permission of Woosim Systems Inc. Trademark a registered trademark of Woosim Systems Inc. All other trademark are the properties of their respective companies.
WSP-i450 Rev. 1.0 Introduction The WSP-i450 is the ideal solution for Mobile banking system , Retail, point of sales, Credit card Transaction, other traveling and mobile computing etc. The general features of WSP-i450 printer are as follows: X Pocket size 151.5×135.7×63.5mm (MSR : 151.5 X 142.5 X 63.5) X Light weight(550g) for true mobility [standard] X Very silent printing thru direct thermal printing method X High speed (60mm/sec, MAX) X High resolution(203dpi : 8dots/mm).
WSP-i450 Rev. 1.0 Operating Precautions Please follow the precautions below to enjoy and maintain the full performance of the printer. X Using the Printer ● Be careful not to drop or bump the printer on a hard surface. ● Do not install the printer in direct sunlight or such areas.
WSP-i450 Rev. 1.0 Note This Device has been evaluated to comply with RF exposure requirement for general use limit in portable condition. It is safe to be used in sold condition. http://www.woosim.
WSP-i450 Rev. 1.0 CONTENTS 1. Outline. ...........................................................................................................................................7 1.1. Model classifications. ...............................................................................................................7 1.2. Product Part Number System....................................................................................................7 1.3. Specifications......................................
WSP-i450 Rev. 1.0 1. Outline. 1.1. Model classifications. WSP-i450 ( ) ( ) Model Interface None: UART/Bluetooth A2 : UART/IrDA Power None : DC 8.4V 1.2. Product Part Number System. Model name 2. Porti-SC30 Interface Spec. Wired S40 SC30 W25 . . . Example) 1. Porti-S40 / Serial/Bluetooth Wireless A RS-232C 1 Bluetooth B TTL 2 IrDA C USB 0 None D RS-485 E Parallel Z None Part No. ⇒ S40/A1 Bluetooth Only Part No. ⇒ SC30/Z1 http://www.woosim.
WSP-i450 Rev. 1.0 1.3. Specifications. Item Specifications Print method Direct thermal line printing Characters per line Eng : 92cpl (MAX) Character size Eng. : 9×24dots, 12×24dots Optional Characters Simplified/Traditional Chinese, Arabic, Cyrillic, Russian, Tukish, Greek, Japanese, Persian, Latin9 and Others upon request. Resolution 203dpi, 8 dots/mm Print width 4-inch ( 104mm, 832dots) Print speed 60mm / sec (MAX) Dimension Kor. : 16×24dots, [24×24dots] 151.5× 135.7 × 63.
WSP-i450 Rev. 1.0 Item Specifications Input (100~250V AC, 50~60Hz) Battery charger Output(8.4VDC/0.8A), 4hours full charge time Temperature Environment conditions MCBF(Mean Cycle Between Failure) Humidity Mechanical Head -10°C ~ 50°C (operating) -10°C ~ 70°C (storage) 30% - 80% (operating) 0% - 95% (storage) 37,000,000 lines Approximately 50 Km < Table 1 > http://www.woosim.
WSP-i450 Rev. 1.0 2. Setting up the printer. 2.1. Printer & Accessories Your printer box should include these items. If any items are damaged or missing, please contact your dealer for assistance. Thermal roll paper Battery pack WSP–i450 Battery charger adaptor Communication cable SAM Connector Shoulder band Smart Card http://www.woosim.
WSP-i450 Rev. 1.0 2.2. Printer Features ▶ Part Name http://www.woosim.
WSP-i450 Rev. 1.0 ▶ Dimensions http://www.woosim.
WSP-i450 Rev. 1.0 2.3. Replacing paper roll. Note : Be sure to use paper rolls that meet the specifications. Do not use paper rolls that have the paper glued to the core because the printer can not detect the paper end correctly. 1. Make sure that the printer is not receiving data; otherwise, data may be lost. 2. Open the paper cover by placing your fingers under the paper cover lock and pull a paper cover lock open. 3. Insert a new paper roll as shown. 4.
WSP-i450 Rev. 1.0 2.4. Power supply 2.4.1. Specified power supply. The following specification is requested for Power supply. Battery Charger : DC 8.4V/0.8A Avoid using power supply which its power capacity of power current is extremely high. 2.4.2. Installing the battery and the belt strap NOTE : ● Before installing or removing the battery pack, ensure the printer is OFF. ● If the printer is not used for long period of time, remove the battery pack from the printer.
WSP-i450 Rev. 1.0 2.4.3. Recharging the battery pack For recharging the battery pack, install the battery pack in the printer. Insert the Battery Charger to the charge connector of the printer. NOTE : ● While charging the printer, turn off the printer power. ● Do not remove the battery during charging. ● The battery is consumable parts and when purchasing, compared to the use hour is gradually decreases.
WSP-i450 Rev. 1.0 2.5. Set operation mode. Change the mode and option using the mode Code. z MODE button : changing Printer MODE status. (Error Lamp) z FEED button : changing OPTION status.
WSP-i450 Rev. 1.0 X When you press FEED button once. → You will see present DENSITY mode in the LCD. → Press MODE Button twice. And then the density has set to Density high. X When you press FEED button once. → You will see present Quality mode in the LCD. → Press MODE Button once. And then the quality has set to Quality high. X When you press FEED button once. → You will see present MARK mode in the LCD. → Press MODE Button once. And then the mark has set to Mark no use.
WSP-i450 Rev. 1.
WSP-i450 Rev. 1.0 Mark Sensor Power Down POWER Lamp ERROR Lamp (Green) (Red) 8 9 10 Option 1 No use 2 Use 1 Low 2 Medium1 3 Medium2 4 High 1 No use 2 1 minute 3 2 minute 4 3 minute 5 4 minute 6 5 minute < Table 2 > http://www.woosim.
WSP-i450 Rev. 1.
WSP-i450 Rev. 1.0 Mark Sensor Power Down POWER Lamp ERROR Lamp (Green) (Red) 8 9 10 Option 1 No use 2 Use 1 Low 2 Medium1 3 Medium2 4 High 1 No use 2 1 minute 3 2 minute 4 3 minute 5 4 minute 6 5 minute < Table 3 > http://www.woosim.
WSP-i450 Rev. 1.0 3. Interface. 3.1. UART(RS-232C or TTL) Pin No. Name Direction Function 1 TxD Output Transmit Data 2 RxD Input Receive Data 3 CD - 4 NC. - 5 GND - Cable Detector Ground The WSP-i450 printer has a UART(RS-232C or TTL) interface and is connected by means of a 5 pin mini USB socket. In the following table, the signals present on the Mini- USB socket are listed: NOTE : ● When data receiving, when it removes the communication cable, it loses a data. http://www.
WSP-i450 Rev. 1.0 3.2. Bluetooth Category Specification Bluetooth Spec. Bluetooth Ver2.1 / Class2 (10m) Frequency Range 2.4GHz ISM BAND (2402 ~ 2480 MHz) RF Power Below 10 dBm Modulation method GFSK Oscillation method PLL Data Transmission Rate 57600bps Fixed. Data bit 8 Data bit Fixed. Parity bit No parity Fixed. Stop bit 1 Stop bit Fixed. 3.3.
WSP-i450 Rev. 1.0 4. Smart Card Module 4.1. General Spec. X Contact Smart Card Reader Module for ISO/IEC-7816 X Support Asynchronous Protocol T=0,T=1 X Smart Card Connection - Short Circuit Current Limitation - 6KV ESD Protection on whole Smart Card Interface - Connector : Friction Type with Smart Card presence detection X 1 SAM (Security Application Module) X EMV Level 1 Certified http://www.woosim.
WSP-i450 Rev. 1.0 4.2. Communication Protocol Sequence 4.2.1. Regular Operation Host Command Module Execution Response 4.2.2. Irregular Operation (Communication Error) 500ms timeout Host Command Command Module Host Command Command is Command Executio Command Error Module CheckSumEr http://www.woosim.
WSP-i450 Rev. 1.0 5. Using the printer. 5.1. Control panel. X Button - FEED Button : When the printer is on, paper can be feed manually by pressing and holding the FEED button for more than one second. - POWER Button : ① When of 5 or more seconds presses and power comes to on or off. ② After pressing the POWER and the FEED button simultaneously, if the ERROR lamp 5 turn signals POWER button is converted with MODE functions. MODE functions are for use to change communication mode. (Refer to 2.5.
WSP-i450 Rev. 1.0 5.2. The self test. The self test procedure will check most of the printer functions. For self test, turn on the power while holding down the FEED Button. The Self-Test checks the following : 1) Make sure paper roll has been installed properly. 2) The Self-Test prints the current printer status, which provides the control ROM version and the communication method setting. 3) After printing the current printer status, Self-Test will print a pattern using the built-in character set.
WSP-i450 Rev. 1.0 6. Consumable Parts. 6.1. Recommended paper. Type : Thermal Paper Paper width : 104mm Paper thickness : 60±5㎛ Outer diameter : Ø50mm or less Recording side : Outside of roll Cautions 1. Do not paste the paper to the core. And the roll paper which has Near end mark printing on its near end is recommended. 2. Chemicals or oil may change the color of paper, or printed Characters may fade. 3. Change of paper color starts from approx 70 ℃.