HL700A USER’S MANUAL WOO YOUNG Telecom CO.,LTD. http://www.wyt.co.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance w ith the instructions, may cause harmful interference to radio communications.
Contents 1. Before Setting up ································ 3 Brief Specification of LCD Monitor Precautions 2. Items ························· 3 ····································· 4 ········································6 3.
5. Appendix ·····································16 Appendix A. Specifications ····························16 Appendix B. 15-pin D-Sub Connector ······················· 17 Appendix C. DPMS Power Saving Mode 6.
1 Before setting up This is 17.0 inch TFT-LCD monitor. Before setting up the LCD Monitor, please read this manual to help your understanding of the LCD Monitor. Brief Specification of LCD Monitor ● Resolution : 17.0 inch SXGA (1280 X 1024@75Hz) ● Color display : 16,777,216 colors ● DPMS (Display Power Management Signaling) ● OSD (On Screen Display) ● Auto Configuration : Hot key ● Speaker [L + R : 3W + 3W = 6W (max)] ● DDC 1/2B : Plug & Play Notise According to PC system, DDC 1/2B may not be supported.
Precautions Check the voltage corresponds t o the local electrical supply before connecting the AC power cord. Do not use Ketone type mat erial (ex. A cetone), Et hyl A lcohol, Toluene, Ethyl Acid or Methyl chloride, to clear the panel. It might permanently damage the panel. Never use the damaged AC power cord. K eeps it away f rom st oves, heaters, f ireplac es and other sources of heat and magnets. Dont’ put your LCD monitor in a location with high humidity and dust.
Don’t touch the screen with a acute nail and pin The LCD monitor consist s of electrical devices. If the LCD monitor is damaged, contact immediately our service center. The LCD monitor can be damaged easily by shock. If you don’t use t he LCD monitor for a long time, unplug the LCD monitor. Don’t use y our LCD moni tor under direct sunlight.
2 Items User Manual LCD Monitor DC Adapter 6
15-pin D-Sub Signal Cable Notise Please make sure the following items are included with your monitor. If any items are missing, contact your dealer.
3 Setting up the LCD monitor Where is a good place to position the monitor? Place the LCD monitor on a solid and flat surface. If dropped, the screen can be damaged easily. Check before connecting the power cord and the signal cable !! Turn off the PC power before connecting the power cord and signal cable to the LCD monitor.
How to connect the power cord and the several cables to the LCD monitor. No.
Connecting Your LCD Monitor Connecting your PC system 1. Connect the 15-pin D-Sub Signal Cable from PC to No.1. 2. If you use a speaker, connect the Audio Cable from PC to No.3. 3. If you use a headphone and earphone, connect the Headphone Cable from PC to No.4. Plug & Play The adoption of the new VESA Plug and Play solution eliminates complicated and time consuming setup. It allows you to install your monitor in a Plug and Play compatible system without the usual hassles and confusion.
4 Adjusting The Monitor The Function Control Buttons How to use the Hot Key. Sound Mute On/Off Button. When you push Auto button, this will optimize image quality automatically. When you push the mode button, the mode changes PC DIGITAL VIDEO1 VIDEO2 TV. When the mode changes, time spend 2~3sec. Menu display On/Off button. Power On/Off toggle button. You can adjust brightness or contrast as not key. When display adjust menu, you can adjust with Left/Right button arrow button.
Main OSD Menu When you push the menu button, you can see below main OSD menu. MAIN MENU BRIGHTNESS/CONTRAST COLOR POSITION OSD SETUP EXIT 1280×1024 79.9KHz / 75Hz BRIGHTNESS/CONTRAST ● Brightness : Changes the overall light intensity of the images being displayed. ● Contrast : Changes the ratio of light intensity between the brightest white and darkest black. ● You can adjust brightness/contrast values that you want by this hot key. ● Gamma : Change the gamma value.
POSITION & CLOCK/PHASE CLOCK/PHASE ● When image is not clear, you can use clock/phase menu. ● PHASE/ CLOCK : Although ‘Auto Adjustment’ automatically finds the optimum values of Clock and Phase parameters as well as image position, it may be necessary for you to adjust those parameters manually. It is recommended for you to use ‘Auto Adjustment’ first. If the adjustment results are not satisfactory, then use Clock and Phase adjustment features to get the best adjustment results.
COLOR ● ● ● ● The tone of color can be changed form bluish white to reddish white. Color1 - Blue type Color2 - Red type RED, GREEN, BLUE - You can adjust red, green and blue values that you want. MAIN MENU BRIGHTNESS/CONTRAST COLOR POSITION OSD SETUP EXIT 1280×1024 79.9KHz / 75Hz COLOR COLOR1 COLOR2 RED ◀ ⋯⋯⋯▶ 50 GREEN ◀ ⋯⋯⋯▶ BLUE ◀ ⋯⋯⋯▶ EXIT OSD MENU ADJUSTMENT & INPUT SOURCE ● Sets the OSD menu display position. ● OSD Position : Moves the OSD menu to the horizontal or vertical direction.
SETUP MENU ● White balance : Automatic djust color (white level) for various input source’s white level. ● Input source : selects input signals. ● Information : display monitor’s information. ● Recall : Discards current setting and replac ed all param otors with the factory default values. MAIN MENU BRIGHTNESS/CONTRAST COLOR POSITION OSD SETUPT EXIT 1280×1024 79.
5 Appendix Appendix A. Display Modes Mode Resolution 720 X 400 Horizontal Vertical Pixel Clock Sync Frequency(KHz) Frequency(Hz) Frequency(MHz) Polarity(H/V) 31.468 70.087 28.322 -/+ 31.468 59.940 25.175 -/- 35.000 66.670 30.240 -/- 37.500 75.000 31.500 -/- 37.879 60.300 40.000 +/+ 48.077 72.188 50.000 +/+ 46.875 75.000 49.500 +/+ 48.363 60.004 65.000 -/- 56.476 70.000 75.000 -/- 60.023 75.029 78.750 +/+ 63.981 DC12V 108.000 +,-/+,- 79.976 DC12V 135.
Appendix B. 15-pin D-Sub Connector ● Input signal : Analog RGB ● 15-pin D-Sub connector Pin No. Signal Name Pin No. Signal Name Pin No.
Appendix C. DPMS Power Saving Mode This monitor has a built-in power management system called DPMS Power Saving Mode. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain period of time. The available modes are “ON”, “Standby”, “Suspend”, and “OFF”.
6 Troubleshooting What you see Screen is blank and power indictor is off “out of range” message Suggested Actions Ensure that the power cord is firmly connected and the LCD monitor is on. Check the maximum resolution and the frequency of the video adaptor. Compare these values with the data in the Display Modes Timing Chart. “No signal input” message Ensure that the signal cable is firmly connected to the PC or video sources. Ensure that the PC or video sources are turned on.
20
Appendix A. Specifications Type Size Panel Display Resolution Frequency TFT active matrix 17 inch 337.92mm×270.336mm Pixel Pitch 0.264mm×0.264mm Display Color 8-bit (16,777,216 colors) Basic 1 2 8 0×1 0 2 4 @ 6 0 H z Maximum 1280×1024@75Hz Horizontal 31.5~80KHz Vertical 56~75Hz Sync Signal Connectors TTL, P. or N.
