FCC RF INTERFERENCE STATEMENT NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Contents Before Setting up -------------------------------------------------------------------------------------------------------------- Brief Specification of LCD Monitor ----------------------------------------------------------------------------------- 3 ------------------------------------------------------------------------------------------------------------------------ 4 --------------------------------------------------------------------------------------------------------------------------
VIDEO Appendix ------------------------------------------------------------------------------------------------------------------------------ 15 ---------------------------------------------------------------------------------------------------------------------------- 17 Appendix A. Display Modes ------------------------------------------------------------------------------------------- Appendix B.
1 Before Setting up This is 15 inch TFT-LCD monitor. Before Setting up the LCD Monitor, Please this manual read help your understanding ok. Brief Specification of LCD Monitor Resolution : 15 inch XGA (1024 X 768 @60Hz) Color display : 16,777,216 colors DPMS (Display Power Management Signaling) OSD (On Screen Display) Auto Configuration : Hot key DDC 1/2B : Plug & Play Speaker : Max 4W [2W X 2W] Notice According to PC system, DDC 1/2B may not be supported.
Precautions Check the voltage corresponds to the local electrical supply before connecting the AC power cord, Do not use Ketone type material (ex. Acetone), Ethyl Alcohol, Toluene, Ethyl Acid or Methyl chloride, to clear the panel. It might permanently damage the panel. Never use the damaged AC power cord. Keep it away from stoves, heaters, fireplaces and other sources of heat and magnets. Don’t put your LCD monitor in a location with high humidity and dust.
Don’t touch the screen with a acute nail and pin The LCD monitor consists of electrical devices. If the LCD monitor is damaged, contact immediately our service center. The LCD monitor can be damaged easily by shock. If you don’t use the LCD monitor for a long time, unplug the LCD monitor. Don’t use your LCD monitor in under direct sunlight.
2 Items User Manual LCD Monitor DC Adapter Notice 15-pin D-Sub Signal Cable 6 Please make sure the following items are included with your monitor. If any items are missing, contact your dealer.
RCA Cable Audio Cable 7
3 Setting up the LCD monitor Where is a good place to position the monitor? Place the LCD monitor on a solid and flat surface. If dropped, the screen can be damaged easily. Check before connecting the power cord and the signal cable !! Turn off the PC power before connecting power cord and signal cable to the LCD monitor.
How to connect the power cord and the signal cable to the LCD monitor. Rear right side Connecting Your LCD Monitor 1. First, you can connect the power cord to the LCD monitor and AC outlet. 2. You can connect the signal cable to the LCD monitor and the PC system. 3. Connect with the audio cable from PC’S sound card to monitor’s SPK jack. 4. Connect DVD or VCR cable to Video Jack (Video). 5. Connect the Audio cable to Audio Jack (Audio(R), Audio(L)).
4 Adjusting The Monitor The Function Control Buttons The function control buttons for monitor are located on the bottom side of the LCD monitor. How to use the function control button.
How to use the Hot Key. AUTO : When you push Auto button, this will optimize image quality automatically. VOLUME : When you push the Left/Right button, you can adjust the volume. Notice While menu displays on the screen, don’t use hot key. If you want to use hot key, you must finish the menu status.
Main OSD Menu When you push the menu button, you can see below main OSD menu. PC Menu 1024 X 768 48.
COLOR The tone of color can be changed from bluish white to reddish white. Color1 - Blue type Color2 - Red type User Color - You can select the color. Color Color 1 Color 2 User Color 1024 X 768 48.
OSD FUNCTION Sets the OSD menu display position. H-Position : Moves the OSD menu to the horizontal direction. V-Position : Moves the OSD menu to the vertical direction. Language : Select OSD language. (English, Espanol, Francais, Deutsch, Italiano) Off timer : OSD display time.
VIDEO Apply Video function to Monitor.
COLOR COLOR : Adjust color intensity of the VIDEO. Color Color Tint Sharpness Exit 16 TINT : Adjust a color tone of the VIDEO. SHARPNESS : Make image of the VIDEO looked sharper.
5 Appendix Appendix A. Display Modes Mode Resolution Horizontal Frequency (KHz) 720 X 400 VGA 640 X 480 SVGA 800 X 600 XGA 1024 X 768 Vertical Pixel Clock Sync Polarity Frequency (Hz) Frequency (MHz) (H/V) 31.468 31.468 35.000 37.500 37.879 48.077 46.875 48.363 56.476 60.023 70.087 59.940 66.670 75.000 60.300 72.188 75.000 60.004 70.000 75.029 28.322 25.175 30.240 31.500 40.000 50.000 49.500 65.000 75.000 78.750 Pin No. Signal Name Pin No. -/+ -/-/-/+/+ +/+ +/+ -/-/+/+ Appendix B.
D-Sub Appendix C. DPMS Power Saving Mode This monitor has a built-in power management system called DPMS Power Saving Mode. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain period of time. The available modes are “ON”, “Standby”, “Suspend”, and “OFF”.
6 Troubleshooting What you see... Suggested Actions Screen is blank and power indicator is off Ensure that the power cord is firmly connected and the LCD monitor is on. “out of range” message Check the maximum resolution and the frequency of the video adaptor. Compare these values with the data in the Display Modes Timing Chart. “No signal input” message Ensure that the signal cable is firmly connected to the PC or video sources. Ensure that the PC or video sources are turned on.
MEMO 20
