Use and Care Manual

ManualsBrandsWorld Dryer ManualsCleaningAirforce Electric Hand Dryer in Brushed Chrome

Operating Instructions and Parts Manual Model “J”

Printed in China

Read and save these instructions. Read carefully before attempting to assemble, install, operate or

maintain the product described. Protect yourself and others by observing all safety information. Failure to comply

with instructions could result in personal injury and/or property damage. Retain instructions for future reference.

WORLD DRYER AIRFORCE

™

High Efficiency Hand Dryer

_____________________________________________________________________________

Description

World warm air hand dryer, powered by universal brush motor, delivers 1100 Watts of drying

power. This hand dryer runs on 120 Volts AC electrical supply. An infrared sensor is used to

automatically turn the dryer on and off. This model is intended for use in commercial, industrial,

office and public facility environments.

General Specifications

Model Drying Cycle Dimensions Weight

(W x H x D)

J-162 Black Auto 8.9” x 10.6” x 6.4” 7.1 lbs

J-974 White Auto (22.6cm x 27cm x 16.2cm) (3.2 Kg)

J-970 Chrome Auto

Electrical Specifications

UL LISTED E320188

Model Type Electrical Input Amperage Watts

J Automatic 120VAC-50/60Hz 9.6A 1100

Unpacking

1. Remove all packing material.

Recycling is recommended.

2. Carefully remove the hand dryer from the shipping carton, using care not to drop the

appliance.

3. Inspect carefully for any damage that may have occurred during transit. Check for any

loose, missing or damaged parts. If the hand dryer is damaged, promptly inform the

dealer where you purchased it.

68-301

Rev v.2

Summary of content (6 pages)

PAGE 1
Operating Instructions and Parts Manual Model “J” Read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage. Retain instructions for future reference.
PAGE 2
Operating Instructions and Parts Manual J WORLD DRYER AIRFORCE™ High Efficiency Hand Dryer General Safety Information DANGER Failure to disconnect the power source before installation can result in serious injury or death from electric shock. − Always disconnect the power source before servicing or installing the hand dryer. DANGER Failure to properly ground this unit could result in severe electrical shock and/or death − − This hand dryer must be properly grounded (Earthed) for safe operation.
PAGE 3
Operating Instructions and Parts Manual J WORLD DRYER AIRFORCE™ High Efficiency Hand Dryer 4. 5. 6. 7. the 4 mounting bolt holes on the wall. Ensure that no reflective object (such as a hand basin) is located directly under infra-red sensor eye; the minimum distance is 18 inches (46 cm). Fasten the base to the wall, using the type of bolts suggested in Table 2. All automatic dryers must have their own dedicated 15 amp circuit. Connect the dryer to the nearest suitable distribution panel.
PAGE 4
Operating Instructions and Parts Manual J WORLD DRYER AIRFORCE™ High Efficiency Hand Dryer REPAIR PARTS LIST FOR AIRFORCE™ HAND DRYER Reference Description Qty Number Part Number 1 Base 14-011577 1 2 Motor Housing 20-011573 1 3 Earth Clip 52-030544 1 4 Cable Clamp 12-011578 1 5 Screw-No6 x 1/2 - Poz Pan 46-040121 4 6 Screw-No6 x 3/8 - Poz Pan 46-040049 1 7 Screw-No6 x 3/8 - Poz Pan 46-010008 4 8 Screw M5x16 Plas Tech 30 Flange HD 46-333 4 9 Seal 59-011574 1 10 Outle
PAGE 5
Operating Instructions and Parts Manual J WORLD DRYER AIRFORCE™ High Efficiency Hand Dryer For Repair Parts, call in the US 1.800.323.
PAGE 6
Operating Instructions and Parts Manual J WORLD DRYER AIRFORCE™ High Efficiency Hand Dryer Troubleshooting Chart Symptom Possible Cause(s) Corrective Action Dryer fails to start. A) No power to unit. B) Defective motor. Check power to unit and connections. Replace motor. Dryer will not shut off or runs 20 seconds, then will not re-start. Sensor is dirty, defective or there is a reflection. 1. Check infra-red eye for dirt or damage. Use plastic lenses cleaning solution and a soft cloth.