User's Manual

1
Index
1
1 second voice messages ........................................... 7-2
1/2 second voice messages ........................................ 7-2
2
2 of 5 Code .............................................................. 2-13
default length setting ........................................... 2-14
enabling check digit ............................................ 2-13
susceptible to mis-reads .......................................... 2-14
2 of 5 Codes
reading variable length bar codes ....................... 2-14
2 of 5 Length ........................................................... 2-14
4
4 digit year option ................................................... 2-19
4 second laser beam.................................................... 2-20
422 Cable pin-outs ............................................B-3, C-2
422 jumpers ...................................................... A-2, B-6
5
5v power supply
needed for Site Testing ......................................... 4-2
6
6 beeps on power up .................................................. 8-6
A
Accumulate Mode ..................................................... E-4
numeric barpad table ............................................. E-4
ActiveX programming ............................................ 6-13
Addressing a Terminal not SIGNed ON
base to host programming ..................................... 6-9
Advanced Features/Functions for Code 39 ............... E-2
AIAG ......................................................................... E-1
aiming dot.................................................................. L-2
aiming dot enabling ................................................... L-3
Area of coverage ....................................................... 4-5
ASCII Code Equivalent Table ................................. O-1
Assigning Error Messages ........................................ 7-4
automatic check back ......................................... 2-9, 3-3
Automatic Check Back ........................................... 6-11
Automobile ID reading ............................................. L-3
Automobile windshield reading ................................ L-3
Avoiding substitutions in scanning .............................. 2-20
B
B11 Rubber Boot for Integrated Laser RF Terminal N-4
Backlight Display ...................................................... 2-7
Bar code data length checking ................................ 2-15
Bar Code ID's .......................................................... 2-12
Bar Code Menu Only setup parameters .................... 2-1
bar code symbol ........................................................ 2-4
Bar Code Type identification .................................. 2-12
Bar Codes
Accumulate Mode ................................................. E-4
character substitution .......................................... 2-17
default settings ...................................................... 2-2
ID character prefix .............................................. 2-12
preambles and postambles .................................. 2-12
trimming characters ............................................ 2-16
using Postamble to add terminator character ...... 2-16
Base and relay blink "channel" on power up ............ 1-3
Base and Relay Setup ............................................. 2-22
Base Reinitialized ..................................................... 8-3
Base Reinitialized message .............................. 6-12, 8-3
Base Shut Down ................................................. 6-9, 8-3
Base Station and Relay cover removal .....................A-1
Base station channel .................................................. 1-3
Base Station failures ................................................. 5-3
Base Station Firmware upgrades ..............................D-2
Base station handshaking .......................................... 5-1
Base Station Initialized Message ............................ 6-11
Base Station installation............................................ 1-2
Base Station location ................................................... 4-1
Base Station Shut Down to Host Logic .................... 8-3
Base Station to Host Pin-outs ................................... C-1
Base Station to Host Programming Formats ............ 6-7
Base to host programming
addressing a terminal not signed on ..................... 6-9
Base Station Initialized message ........................ 6-11
Illegal Commands ...................................... 6-10, 6-11
Sequence Error Message..................................... 6-10
Serial Reply........................................................... 6-7
SIGN ON .............................................................. 6-8
SIGN OUT ............................................................ 6-9
Basic architecture of host-terminal dialog ................ 6-1
Basic command format ............................................. 6-1
Basic RF System communications ........................... 3-1
Batteries .................................................................. 2-18
battery charging ........................................................ 1-6
Battery Life indicator ................................................ 1-5
Battery Status indicator ........................................... 2-18
Baud Rate for serial printer ..................................... 2-21
Beep Tone ............................................................... 2-18
Beeping
and Accumulate Mode .......................................... E-4
changing the tone or pitch................................... 2-18
during setup configuration .................................... 2-2
Before you begin programming ................................ 5-1
BEGIN key
transmitting ASCII 23 to host ............................. 6-12
Belden 1227A1 wire for 422 cables ................. B-3, C-2
Blocking unauthorized listening .................................... 2-6
bright light problems
aiming dot ............................................................. L-3
Buffer Reinitialized ................................................... 8-3
C
Cable pin-outs ........................................................... C-1
Cables
for relays ....................................................... B-3, C-2
needed for voice message cloning ........................ 7-5
types ...................................................................... 1-2
Cables for Zebra Cameo Printer ................................. C-3
Cameo magstripe ...................................................... 6-4
Cameo Printer ......................................................... 6-33
Cameo Printer Pin-outs .............................................. C-3
Caps Lock ON
Code 39 setup parameter .................................... 2-10
CCD pin-outs ............................................................ C-3
Change Batteries ....................................................... 8-3