User's Manual

3
Double Decode .......................................................... 2-20
double decode option ................................................ L-2
Double-scan checking ........................................ 2-20, L-3
DOWN ARROW key
transmitting ASCII 29 to host ............................. 6-12
Downloading firmware from your computer to the
terminal ................................................................ D-1
E
EDI
UCC -128 bar code ................................................H-2
Enabling 2 of 5 check digit ..................................... 2-13
Enabling transmission of NSC character ................ 2-11
Enabling UPC/EAN check digits ............................ 2-11
Encore Printer ......................................................... 6-34
END key
transmitting ASCII 24 to host ............................. 6-12
End of Cloning Hit Any Key .................................... 7-5
End Setup
scanning to exit Setup mode ................................. 2-2
ENTER key
eliminiting for Arrow Keys ................................... 2-7
ENTER key elimination
for Control Keys ................................................... 2-6
Entering a Security Code on an RF Terminal ................. 2-6
EPROM changes ...................................................... D-2
Eprom version identification ..................................... 1-7
Eprom versions
Australia/New Zealand ......................................... 2-6
US/Canada/Mexico ............................................... 2-6
Error messages
Base Reinitialized ................................................. 8-3
voice messages ...................................................... 7-4
Establishing communication with a Relay ................ 4-4
Evaluating your areas range ...................................... 3-5
examples
valid commands from host to terminal ................. 6-2
Exiting One-Way mode ............................................ 3-5
Extension cables on base station ................................. 1-2
extra characters at beginning or end of data ...................... 8-7
F
F1 as "escape" key .................................................... 1-8
F1 to exit modes ........................................................ 1-8
F34 DB25 Null Modem Cable Pin-outs ................... C-1
F36 DB9 Straight Cable Pin-outs ............................. C-1
factors to consider before you begin programming .. 5-1
Failure planning ........................................................ 5-1
Failure Planning ........................................................ 5-2
Firmware Download for Terminal
Failsafe ................................................................. D-1
Normal ................................................................. D-1
Firmware revision
how to find our what yours is ............................... 1-7
Firmware Upgrades .................................................. D-1
first screen keeps showing up ................................... 8-6
Fixing substitution - laser read .................................. L-3
Forcing "shifted" cursor entry ................................... 6-3
Forgetting your Security Code ...................................... 2-6
Frequency and Jumper Changes .............................. A-1
Frequency Changes .................................................. A-2
Full ASCII Extension to Code 39 ............................. E-3
Function Code 1 transmission .................................. H-1
Function keys .......................................................... 6-12
G
Getting into Site Test Mode ...................................... 4-2
Global Computer Supplies ........................................ C-1
GREEN LED ............................................................ 8-4
H
H11 Laser Holder ......................................................N-2
hands free laser scanning ......................................... M-1
Hardware Failures ..................................................... 5-2
Headphone Volume .................................................. 2-9
Host Logic Error ................................................ 6-9, 8-3
Host programming guidelines ................................... 6-1
Host to Terminal Programming ................................ 6-1
How many terminals per base? ................................. 4-6
How Relay Stations work ......................................... See
How Site Testing works ............................................ 3-5
How the Two-Way RF System works ...................... 3-1
How to change the batteries ............................... 1-5, 1-6
How to reach Worthington Data Solutions ............... 8-8
How to record voice messages ................................. 7-4
How to replace the EPROM .....................................D-1
How to scan a bar code ............................................. L-1
I
I can’t communicate at all ......................................... 8-5
ID assignment for Relay ...........................................A-2
ID’s for bar code type ............................................. 2-12
Identifying the type of bar code read ...................... 2-12
If you are not connecting to a PC serial port ............ 1-2
Illegal Command
Base to host programming ......................... 6-10, 6-11
illegal statements
how RF Terminal handles ................................... 2-22
Improving results from Site Test .............................. 4-3
Incorrect reading ....................................................... L-3
Incorrect Routing for Wiring .................................... B-3
Input data from external keyboard ............................ 6-3
Installation ................................................................. 1-1
installing base - not on PC .................................... 1-2
installing base on PC serial port ........................... 1-2
Installation Summary ................................................ 1-1
Installing the R/F Terminal Utilities Software ......... 1-8
Interleaved 2 of 5
check digit calculation ........................................... I-1
data length ...................................................... 2-14, I-1
default settings .................................................... 2-13
Interleaved 2 of 5 Code Specifications ...................... I-1
ISBN bar codes
transmitting in ISBN format ............................... 2-11
ISBN format output ................................................ 2-11
ISBN Specifications ................................................... J-2
J
Jumpers
RS-422 termination ...............................................A-2
K
key symbol ................................................................ 2-4
Keypad Only setup parameters ................................. 2-1
Keypad Setup Menu
parameter groups .................................................. 2-4
L
Label Code 4 and 5