User's Manual

6
Q
quiet zone................................................................... 8-7
R
R/F Serial Pin-outs ................................................... C-1
R/F Terminal Firmware Upgrades ........................... D-1
R/F Terminal Menu Functions
ONE-WAY ............................................................ 1-6
SETUP MODE ...................................................... 1-6
SIGN ON ............................................................... 1-6
SITE TESTING ..................................................... 1-6
Radio traffic contention ............................................. 4-6
Raising the Base station to increase range ................... 4-1
Range problems ......................................................... 8-5
Reader doesn't beep when reading bar codes ............ 8-7
reading credit cards ................................................... 6-4
reading magstripe ...................................................... 6-4
reading through a windshield ................................... L-3
Reading through a windshield .................................. L-3
reaing in sunlight using aiming dot .......................... L-3
Re-assigning character codes .................................. 2-17
rechargeable batteries .............................................. 2-18
recharging battery procedure ..................................... 1-6
Recording a voice message using the microphone ... 7-3
Recording and Playback of Voice Messages ............ 7-3
Recording time alloted for voice messages ............... 7-2
Recovering from hardware failures ........................... 5-2
Recv Setup/Voice Please Wait .................................. 7-5
Red LED .................................................................... 8-4
Reduced Space Symbology code ............................ 2-14
Re-initailizing terminals ............................................ 6-2
Reinitialization
of Base Station with Terminal Signed-On .......... 6-12
Re-initialize command .............................................. 6-3
Relay Cannot be Heard.............................................. 8-4
Relay Existence setup parameter
how to set for Relays ............................................. 4-4
Relay ID - configuring ............................................ 2-23
Relay ID and Frequency ........................................... B-4
Relay n Cannot Be Heard by the Base ............. B-4, B-6
RELAY n CANNOT BE HEARD BY THE BASE . 4-4
Relay Setup .............................................................. 2-22
Relay Station failures ....................................... B-3, B-6
Relay Station RS422 Pin-outs .......................... B-3, C-2
Relay stations cable failures ............................. B-3, B-6
Relay Stations
changing a Base to operate as a Relay ................. A-1
connecting ............................................................ B-1
multi-dropping additional ..................................... B-1
no serial parameters needed ................................. B-2
troubleshooting unconnected relay .............. B-4, B-6
using to extend RF range ...................................... B-1
Relay test cable ......................................................... B-4
relay wiring ............................................................... B-2
Relays
overlapping area with Base ................................... 4-5
RS-422 termination ...................................... A-2, B-6
resending prompts after a sign-out ............................ 5-3
Reset ........................................................................ 2-21
response time is poor ................................................. 8-5
Restrictions on bar code data length ....................... 2-15
Restrictions on using arrow keys to transmit special
characters ............................................................. 6-12
Results of Site Test ................................................... 4-2
retransmission ............................................................ 3-3
returns to 1st screen ................................................... 8-6
RF 700 Configuration Utility .................................. 2-22
RF link test ................................................................ 2-23
RF System
Base Station failures .............................................. 5-3
before you begin programming ............................. 5-1
creating programs to prompt the terminal ............. 6-1
operator errors ....................................................... 5-3
planning for expansion .......................................... 5-2
planning for failures .............................................. 5-1
planning for hardware failures .............................. 5-2
Relay station failures .................................... B-3, B-6
using Demo programs to test system .................... 5-2
RF System Setup ....................................................... 2-1
RF Terminal
how it finds a Relay .............................................. 4-4
installation ............................................................. 1-4
opening screen ....................................................... 1-6
sleep mode and wake up intervals ....................... 3-3
system components ................................................. 1-1
RF Terminal Cases and Holsters .............................. N-4
RF Terminal Channel ................................................ 2-5
RF Terminal Default Settings ................................... 2-1
RF Terminal ID ......................................................... 2-5
in programing message from host to terminal ...... 6-1
RF Terminal Problems .............................................. 8-6
RF Terminal setup
using keypad to setup ............................................ 2-3
using the bar coded setup menu ............................ 2-2
RF Terminal Setup .................................................... 2-1
2 of 5 Code .......................................................... 2-13
2 of 5 Length ....................................................... 2-14
Batteries ............................................................... 2 -18
Baud Rate for serial printer ................................. 2-21
Beep Tone ........................................................... 2-18
Characters ............................................................ 2-17
Code 3 of 9 .......................................................... 2-10
Data Bits setting for serial printer ....................... 2-21
Date Format ......................................................... 2-18
Display of Year ................................................... 2-19
ENTER key elimination for Control Keys Only .. 2-6
Laser Scanner Options ........................................ 2-20
LCD Backlight Display Mode .............................. 2-7
LCD Display Mode ............................................... 2-7
MSI/Plessey......................................................... 2-14
Parity for serial printer ........................................ 2-21
Preamble .............................................................. 2-15
Protocol setting for serial printer ........................ 2-21
Reset .................................................................... 2-21
RF Terminal Channel ............................................ 2-5
RF Terminal ID ..................................................... 2-5
RSS-14 code ........................................................ 2-14
Security Code ........................................................ 2-6
Set Date ............................................................... 2-19
Set Time .............................................................. 2-19
Shut Down Time ................................................. 2-20
Skip Opening Screens ........................................... 2-8
Stop Bits setting for serial printer ....................... 2-21
Voice Message Partitions ........................... 2-19, 2-20
RF Terminal Setup
Codabar ............................................................... 2-13
Code 128 ............................................................. 2-12
Code 93 ............................................................... 2-15
UPC/EAN ............................................................ 2-11
RF Terminal Setup Menu on keypad ........................ 2-3