User's Manual

2
setting jumper for programming ........................... A-2
Stop Bits ............................................................... 1-30
Xon/Xoff Sensitive............................................... 1-29
Base Station Setup Parameters .................................1-29
Base Station Setup using the RF Terminal ..............1-28
Base Station Shut Down to Host Logic...................... 8-3
Base Station to Host Pin-outs.................................... C-1
Base Station to Host Programming Formats.............. 6-6
Base to host programming
addressing a terminal not signed on .......................6-8
Base Station Initialized message ..........................6-10
Illegal Commands................................................. 6-10
Sequence Error Message ........................................ 6-9
Serial Reply ............................................................ 6-7
SIGN ON................................................................ 6-7
SIGN OUT .............................................................6-8
Basic architecture of host-terminal dialog .................6-1
Basic command format............................................... 6-1
Basic RF System communications............................. 3-1
Battery conservation technique .................................. 3-3
Battery Functions .......................................................1-4
Battery Life indicator ................................................. 1-6
battery recharging circuitry.......................................... 1-5
Battery Status indicator ............................................1-22
Baud Rate
Base Station setup ................................................1-29
Baud Rate for serial printer ......................................1-26
Beep Tone................................................................. 1-22
Beeping
and Accumulate Mode ...........................................E-4
changing the tone or pitch .................................... 1-22
during setup configuration ..................................... 1-2
Before you begin programming ................................. 5-1
BEGIN key
transmitting ASCII 23 to host .............................. 6-11
Belden 1227A1 wire for 422 cables.................. B-3, C-2
Blocking unauthorized listening .................................. 1-9
Body of message command........................................ 6-1
bright light problems
aiming dot............................................................. M-3
Buffer Reinitialized .................................................... 8-3
C
C21 Cameo Printer Cable.......................................... C-3
Cable pin-outs............................................................ C-1
Cables
for relays........................................................ B-3, C-2
needed for voice message cloning.......................... 7-6
types........................................................................1-3
Cables for Zebra Cameo Printer...................................C-3
Cameo Printer...........................................................6-31
Cameo printer enabled................................................ 1-8
Cameo Printer Pin-outs................................................C-3
Caps Lock ON
Code 39 setup parameter ...................................... 1-14
Case for Booted Integrated Laser RF Terminal ........ N-6
CCD pin-outs............................................................. C-3
Change Batteries......................................................... 8-3
Change Batteries......................................................... 1-6
Changing ASCII characters used to accomodate
XON/XOFF ..........................................................6-10
Changing Base setup from host................................ 1-32
Changing character output ....................................... 1-22
Changing Display mode from 6 line to 4 line ..........1-10
Changing more than one setup parameter at
a time using the bar coded setup menu...................1-2
Changing Relay setup from host ..............................1-32
Changing the AA batteries on the RF
Terminal..................................................................1-6
Changing the Base Station parameters from
the Host.................................................................1-32
Changing the default voice messages.........................7-5
Changing the frequency on a Base or
Relay ..............................................................A-3, B-5
Changing the RF Terminal frequency ........................1-5
Changing the RF Terminal ID ....................................1-5
Changing the RF Terminals automatic
shut-off time..........................................................1-24
Changing the Speaker Volume ...................................7-6
Changing the voice message partitions ......................7-2
Character codes
reassigning ............................................................1-22
Characters .................................................................1-22
Check Character
Code 39.................................................................. E-2
Check digits / Checksums
and Accumulate Mode........................................... E-4
Check Digits / Checksums
Code 128................................................................H-1
Code 39.................................................................. E-2
Code 93.................................................................. F-1
Interleaved 2 of 5 .................................................... I-1
MSI / Plessey .........................................................K-1
UPC/EAN ............................................................... J-3
Check digits/checksums ............................................H-2
Checking frequency for Site Test ...............................4-2
circuit board diagram.................................................A-1
Clearing lines on a 6 line display................................6-2
Clearing lines on terminal
4 line vs. 6 line display ...........................................6-5
Clearing lines on terminal screen ...............................6-2
Clearing terminal screen.............................................6-2
cloning Terminal setup
to other terminals ....................................................7-5
Cloning voice messages..............................................7-5
cables for.................................................................7-6
Cloning Voice Messages from RF Terminal
to RF Terminal........................................................7-5
CLSI format for Codabar..........................................1-17
CLSI format of Codabar ...........................................1-17
Codabar.....................................................................1-17
CLSI format ..........................................................1-17
Start/Stop transmission ..........................................G-1
transmitting start and stop characters .....................1-17
Codabar Specifications ..............................................G-1
Code 128 ...................................................................1-16
Code 128 Specifications ............................................H-1
Code 128 subsets .......................................................H-1
Code 3 of 9
setting up...............................................................1-14
Code 39
about Accumulate mode ........................................ E-4
enabling the Mod 43 check character .....................1-14
transmitting start and stop characters ...................1-14
using Caps Lock ON.............................................1-14
Code 39 Advanced Features/Functions ..................... E-2
Code 39 Specifications .............................................. E-1
Code 93 Specifications .............................................. F-1
Code 93 .....................................................................1-19