User's Manual

4
Failure planning...................................................5-1, 5-2
Finishing base configuration ....................................1-31
Firmware revision
how to find our what yours is................................. 1-7
Firmware Upgrades ................................................... D-1
Fixing substitution - laser read ................................. M-3
Forcing "shifted" cursor entry .................................... 6-3
Forgetting your Security Code..................................... 1-9
French frequencies .....................................................1-7
Frequencies
Australia/New Zealand........................................... 1-6
Korean .................................................................... 1-7
US/ Canada/ Mexico ..............................................1-6
Frequency
adding additional Base Stations ............................. 4-8
How to find out what yours is on
RF Terminal .......................................................1-8
Frequency and Jumper Changes................................ A-1
Frequency bank
Relays only on 0 ...................................................1-31
Frequency Bank.......................................................... 1-8
Base Station setup ................................................1-31
Frequency Changes ................................................... A-3
Frequency of RF Terminal
default .....................................................................1-5
Full ASCII Extension to Code 39 ..............................E-3
Function Code 1 transmission ................................... H-1
Function keys ........................................................... 6-11
G
German frequencies....................................................1-7
Getting into Site Test Mode .......................................4-2
Going back one screen using F1 key.......................... 1-9
Going directly to application on
power-up......................................................1-11, 1-12
guidelines for evaluating Site Test .............................4-3
H
H11 Laser Holder ...................................................... N-4
Hardware changes on the RF Terminal..................... A-4
Hardware Failures ...................................................... 5-2
Headphone.................................................................. 7-6
Host application
slowing down system ............................................. 8-6
Host computer slowing down RF System ..................8-6
Host Logic Error..................................................6-9, 8-3
Host programming base setup changes ....................1-32
Host programming guidelines .................................... 6-1
Host programming Relay setup changes..................1-32
Host Response Delay................................................ 1-13
using to cut down radio traffic ...............................3-3
Host to Terminal Programming.................................. 6-1
Hostless demo using One-Way mode ........................ 3-4
How many terminals per base? ..................................4-7
How Relay Stations work...........................................See
How Site Testing works .............................................3-5
How the One-Way RF System works ........................ 3-4
How the Two-Way RF System works ....................... 3-1
How to change the batteries ....................................... 1-6
How to control the RF Terminal from the host.......... 6-1
How to determine frequency on Base or Relay .........1-4
How to determine number of terminals per
Base ........................................................................ 4-8
How to get in and out of modes on RF
Terminal..................................................................1-9
How to get into One-Way mode.................................3-4
how to open base or relay case ..................................A-1
How to reach Worth Data ..........................................8-9
How to record voice messages ...................................7-4
How to replace the EPROM ......................................D-2
How to scan a bar code............................................. M-1
I
I can’t communicate at all ..........................................8-5
ID assignment for Relay ....................................A-3, B-6
ID’s for bar code type ...............................................1-16
Identifying the type of bar code read........................1-16
If you are not connecting to a PC serial port ..............1-3
Illegal Command
Base to host programming....................................6-10
illegal statements
how RF Terminal handles.....................................1-26
Improving results from Site Test ................................4-3
Incorrect reading....................................................... M-3
Incorrect Routing for Wiring..................................... B-3
Initializing a Terminal ................................................6-1
Installation ..................................................................1-1
installing base - not on PC ......................................1-3
installing base on PC serial port .............................1-3
Installation Summary..................................................1-2
Installing the B11 Rubber Boot .................................N-6
Installing the R/F Terminal Utilities Software ...........1-9
Interleaved 2 of 5
check digit calculation ............................................ I-1
data length....................................................... 1-18, I-1
default settings......................................................1-17
Interleaved 2 of 5 Code Specifications....................... I-1
intervals
wake up intervals for terminal..................................3-3
ISBN bar codes
transmitting in ISBN format .................................1-15
ISBN format output ..................................................1-15
ISBN Specifications.................................................... J-2
J
JP103..........................................................................A-2
JP103 jumper for Programming mode on
Base.......................................................................1-27
JP3 - laser decode light jumper..................................A-4
JP4 - battery recharge jumper....................................A-5
Jumper Changes.........................................................A-2
jumpering the Base station for programming ............A-2
Jumpers
RS-422 termination........................................A-3, B-6
K
key symbol..................................................................1-4
Keypad Only setup parameters...................................1-1
Keypad Setup Menu
parameter groups ....................................................1-4
Korea Eprom versions ................................................1-7
Korean frequencies .....................................................1-7