User's Manual

6
Partitions
changing for voice messages.................................. 7-2
for voice messages.................................................. 7-2
Password..................................................................... 1-3
PDF 417 scanners....................................................... 6-3
Performance Issues..................................................... 4-1
Performing a Site Test................................................ 4-2
PICK requirements...................................................... 8-6
Piggyback Feature ......................................................L-1
Piggyback Laser Installation ......................................L-1
Pin-outs...................................................................... C-1
Zebra Cameo Printer ...............................................C-3
Planning for expansion............................................... 5-2
Planning for hardware failures ................................... 5-2
Planning for system failures .......................................5-1
Playing a voice message on a terminal ......................6-2
Playing back a recorded voice message .....................7-3
Plessey code............................................................... K-1
Poor lighting situations
suggestions for dealing with................................... 7-1
poor read rates when scanning bar codes ...................8-7
Portable Printer Pin-outs
Zebra Cameo ...........................................................C-3
Portable Printers
Zebra Cameo Printer ............................................6-31
Portable printers supported
Zebra Cameo/Encore.............................................. 1-8
portable printing ....................................................... 6-32
Portkey
using with One-Way mode..................................... 3-4
Postamble .................................................................1-20
using in One-Way mode to send terminator .......... 3-5
using to check data length in
NON PORTABLE mode.................................. 1-21
Postambles
selective trimming ................................................ 1-21
potentiometer to increase speaker volume ................ A-5
powering up base station after programming........... 1-33
Power-up
6 beeps from terminal............................................. 8-7
Preamble................................................................... 1-19
selective trimming ................................................ 1-20
using in One-Way mode to send
Terminal ID ............................................................ 3-5
using to check data length ....................................1-20
Prefix for bar code types ..........................................1-16
Preparing the Base Station for Setup........................ 1-27
Press Enter When Ready prompt during
Site Test.................................................................. 4-3
Preventing another Base from listening ....................... 1-9
Preventing unauthorized listening on system........... 1-30
Printer
setting Parity to match serial printer......................... 1-26
Problems reading Bar Codes ......................................8-7
Problems with a new installation ...............................8-2
Programming
Base to Host formats .............................................. 6-6
Programming Commands
clearing individual lines on terminal screen........... 6-2
clearing terminal screen .........................................6-2
displaying date and time on terminal .....................6-2
making terminal beep ............................................. 6-2
outputting data to a serial device on terminal ........ 6-2
playing a voice message on a terminal...................6-2
reinitializing terminals............................................ 6-2
sample statements ...................................................6-4
Programming for the RF Terminal .............................6-1
Programming Mode jumper.......................................A-2
Programming voice messages ....................................7-1
Programming Voice Messages ...................................7-3
Protocol setting for serial printer ..............................1-26
Q
quiet zone....................................................................8-8
R
R/F Serial Pin-outs..................................................... C-1
R/F Terminal Firmware Upgrades.............................D-2
R/F Terminal Menu Functions
ONE-WAY .............................................................1-7
SETUP MODE .......................................................1-7
SIGN ON ................................................................1-7
SITE TESTING ......................................................1-7
radio traffic
reducing by adding Base station.............................4-7
Radio traffic contention ..............................................4-7
Raising the Base station to increase range....................4-2
Range problems ..........................................................8-6
Reader doesn't beep when reading bar codes .............8-7
Reading through a windshield .................................. M-3
reading in sunlight
aiming dot ............................................................. M-3
Re-assigning character codes....................................1-22
Rechargeable Batteries
how to order.............................................................1-5
Recharging time for batteries ....................................A-5
Recording a voice message using the
microphone .............................................................7-4
Recording and Playback of Voice Messages..............7-3
Recording time alloted for voice messages ................7-2
Recovering from hardware failures ............................5-2
Recv Setup/Voice Please Wait ...................................7-6
Reducing radio traffic .................................................3-3
Re-initailizing terminals .............................................6-2
Reinitialization
of Base Station with Terminal Signed-On............6-11
Relay Cannot be Heard...............................................8-4
Relay Existence ..........................................................1-8
Relay Existence setup parameter
how to set for Relays ..............................................4-4
Relay ID and Frequency ............................................B-5
Relay n Cannot Be Heard by the Base .............. B-4, B-7
RELAY n CANNOT BE HEARD BY THE
BASE ......................................................................4-5
Relay setup changes from host .................................1-32
Relay Station failures......................................... B-4, B-7
Relay Station RS422 Pin-outs ...........................B-3, C-2
Relay stations
cable failures.................................................. B-4, B-7
Relay Stations
connecting.............................................................. B-1
how they work ........................................................4-4
multi-dropping additional ......................................B-1
no serial parameters needed................................... B-2
troubleshooting unconnected relay................B-4, B-7
using to extend RF range ....................................... B-1
Relay test cable ..........................................................B-4
relay wiring................................................................ B-2