User's Manual

8
Serial printer setup paramters on terminal ............... 1-26
Serial Reply
Base to host programming...................................... 6-7
Set Date ....................................................................1-23
Set Time.................................................................... 1-23
Setting the Relay ID .................................................. A-3
Settings for jumpers................................................... A-2
Setup
Backlight Duration ...............................................1-11
Base Station.......................................................... 1-27
RF Terminal ...........................................................1-5
Setup Cloning
to other terminals.................................................... 7-5
Setup Menu
"Reset" bar code ................................................... 1-25
Baud Rate .............................................................1-26
Data Bits ...............................................................1-26
Parity..................................................................... 1-26
RF Terminal Frequency .........................................1-5
RF Terminal parameters.........................................1-5
Stop Bits ............................................................... 1-26
Terminal ID ............................................................ 1-5
SETUP MODE
using to program voice messages........................... 7-3
Setup or playback voice messages ............................. 7-3
Sharing a Base Station with multiple
Terminals.............................................................. 1-13
shelf label printing.................................................... 6-32
Short voice messages
preferable to use................................................. 7-1
Shut Down Time ......................................................1-24
Shut Down Time feature ............................................ 1-4
SIGN ON
Base to host programming...................................... 6-7
difference between 4 line and 6 line
display................................................................. 6-8
for 6 line display terminal ...............................6-6, 6-8
SIGN ON for 6 line display ....................................... 1-10
SIGN OUT
Base to host programming...................................... 6-8
missing the message ............................................... 5-3
Signing out in mid-transaction ................................... 5-3
site map....................................................................... 4-2
Site survey .................................................................. 3-5
Site Test Mode
brief description of .................................................3-1
Site Testing
frequency changes ................................................... 4-2
getting into.............................................................. 1-8
how it works ...........................................................3-5
using a Site Map to record results .......................... 4-2
Site Testing in Progress message ............................... 4-3
Six beeps on power-up ...............................................8-7
Skip Opening Screens ..............................................1-11
Skipping the Mode Menu ...........................................1-9
sleep mode for RF Terminal ........................................ 3-3
Speaker / Batteries.................................................... 1-22
speaker volume.......................................................... A-4
Speaker volume
changing .................................................................7-6
Speeding up data collection by using
Voice Prompts ........................................................ 7-1
splitting your terminals between Base stations ..........4-8
Start Setup
scanning to enter Setup mode................................. 1-2
Start/stop characters
transmitting for Codabar........................................1-17
transmitting for Code 39.......................................1-14
STATUS key
reserved for date/time only ...................................6-11
using to determine battery life ...............1-6, 1-12, 8-2
Steps for installation ...................................................1-2
STK bar code ............................................................1-16
Stop Bits
Base Station setup.................................................1-30
Stop Bits for serial printer ........................................1-26
Storage Tek bar code ................................................1-16
Storage Tek Tape Label code ...................................1-16
substitution errors ..................................................... M-2
Substitutions
avoiding with laser scanner ....................................1-3
Substitutions of data ................................................. M-3
sunlight problems,
aiming dot ............................................................. M-3
Support for Zebra printers ..........................................1-8
Surveying a site...........................................................4-1
Symbol 3200ER Scanner...........................................N-3
System architecture.....................................................6-1
T
T46 Holster for LT model RF Terminal with B11
Rubber Boot...........................................................N-6
T47 Piggyback Terminal Carrying Case ...................N-6
T49 Holster for RF Terminal.....................................N-5
Tape library bar code ................................................1-16
TCP/IP Terminal Programming................................6-21
Terminal ID
how to find out what yours is .................................1-7
use in Two-Way mode............................................3-2
Terminal ID in One Way mode ..................................3-5
Terminal keys - transmitting ASCII values..............1-10
Terminal setup
Security Code..........................................................1-9
Terminal Setup Cloning
to other terminals ....................................................7-5
Terminating a programming message ........................6-2
Terminator character.................................................1-20
Testing Base Station communications.............. 1-33, 8-5
Testing communication with a Relay ........................ B-4
Testing the Relay ....................................................... B-4
Testing the terminal-to-relay link ..................... 1-33, 8-5
Thru-put considerations ..............................................4-7
Time Set....................................................................1-23
time stamping in Terminal..........................................6-3
Tips for Using Voice Prompts ....................................7-1
Trailing character trimming......................................1-21
Transmission Failed..................................................1-28
TRANSMISSION FAILED ............................... 3-3, 3-4
Transmitting Bar Code ID's......................................1-16
Transmitting characters before or after bar
code data ...............................................................1-19
Transmitting Codabar start and stop
characters...............................................................1-17
Transmitting EAN-8/UPC-E in original
formats...................................................................1-16
Transmitting through walls.........................................4-1
Trimming by bar code type
using bar code ID and postamble .........................1-21
using bar code ID and preamble/postamble .........1-20