User's Manual

9
Trimming characters from data........................1-19,1-21
Trimming leading characters
using Preamble..................................................... 1-19
Trimming trailing characters
using Postamble ................................................... 1-20
Troubleshooting ......................................................... 8-1
electrical noise problems with Relays ................... 4-5
wiring problems with Relays ................................. 4-5
Troubleshooting new installation............................... 8-2
Turning off the speaker
when using the earphone........................................ 7-7
Turning on the R/F Terminal ..................................... 1-4
Turning the speaker off to conserve batteries.......... 1-22
Two-Way Mode
brief description of ................................................. 3-1
in depth description of how it works ..................... 3-2
Typical coverage ........................................................ 4-6
U
UCC 128 Serial Shipping Container bar code .......... H-2
UCC/EAN Code 128
enabling/disabling ................................................ 1-16
UCC-128/ EAN-128 ................................................. H-1
UK Frequencies.......................................................... 1-7
UNIX requirements and problems ....................1-33, 8-5
UP ARROW key
transmitting ASCII 28 to host.............................. 6-11
UPC 2 and 5-character supplemental codes ...............J-2
UPC/EAN................................................................. 1-15
about........................................................................J-1
Check digit ..............................................................J-1
compressed format .................................................1-16
default settings ..................................................... 1-15
expanding UPC-E ................................................ 1-16
guidelines for use ..................................................... J-2
NSC and check digit ............................................ 1-15
NSC's and check digits......................................... 1-15
numbering conventions ............................................J-2
supplemental codes .............................................. 1-15
UPC-A - adding a country code........................... 1-15
UPC-A in 13 digit EAN format ........................... 1-15
UPC/EAN check digits
enabling transmission of ...................................... 1-15
UPC/EAN checksum character...................................J-3
UPC/EAN Specifications............................................J-1
UPC/EAN Supplements
enabling/disabling ................................................ 1-15
UPC-E Checksum Calculation....................................J-4
UPC-E0 and UPC-E1............................................... 1-16
UPC-E1
enabling reading of............................................... 1-17
Upgrading firmware in Base,Relay or
Terminal ................................................................ D-1
US Date Format ....................................................... 1-23
USA / Canada / Mexico frequencies.......................... 1-6
USA/Canada/Mexico
EPROM version identification............................... 1-6
Using Arrow Keys to transmit characters................ 1-10
Using RFDEMO to troubleshoot radio ...................... 8-6
Using the bar code RF Terminal Setup Menu ........... 1-2
Using the Demo Programs before
programming.......................................................... 5-2
Using the keypad to setup the RF Terminal .............. 1-3
Using the Relay instead of the Base to
communicate ..........................................................4-5
Using the RF Terminal keypad .................................. 1-4
Using Windows RF Terminal EPROM
Loader.................................................................... D-3
Utilities CD ................................................................. 1-9
V
Vehicle ID reading ................................................... M-3
Version
9075 ...............................................................1-11, 6-5
VIN reading.............................................................. M-3
Voice Cloning Cable #T15......................................... 7-5
Voice message "command"........................................ 6-2
Voice message mapping............................................. 7-2
Voice Message Operations......................................... 7-1
Voice message partitions
changing .................................................................7-2
Voice Message Partitions ......................................... 1-24
Voice messages
cloning from RF Terminal to RF Terminal............ 7-5
eaphone only option .............................................1-22
error conditions....................................................... 7-5
playback.................................................................. 7-3
record error messages for all situations.................. 7-2
use a calm voice when recording ........................... 7-1
varying your tone of voice when recording ........... 7-2
Voice Messages
changing the time allotments................................ 1-24
Voice messaging
short messages are preferable................................. 7-1
Voice Operations selection on SETUP Menu............ 7-3
Voice Prompts
helping to limit mistakes ........................................ 7-1
Volume potentiometer................................................ 7-6
W
Waiting for Base to Acknowledge ............................. 8-3
Waiting on Host Prompt............................................. 8-3
WAITING ON HOST PROMPT ............................... 3-2
Waiting on Host Prompt” ...........................................8-3
Wand Scanners ......................................................... M-1
Wand vs. keypad entry ............................................... 6-3
WDTRI password....................................................... 1-3
What to do with data after a failure............................ 5-2
What to do with data after an operator error .............. 5-3
Why Use Voice Messages and Prompts?................... 7-1
Windows 95 com port setup....................................... 8-6
Windows ActiveX programming ............................. 6-12
Windows RF Loader program................................... D-2
Windows TCP/IP terminal programming ................ 6-21
Windows’ Terminal
using with One-Way mode..................................... 3-4
Windshield Reading ................................................. M-3
Wrong data ............................................................... M-3
X
Xmit Setup/Voice Please Wait................................... 7-6
XON/XOFF
changing ASCII characters to avoid
conflict.............................................................. 6-10
Xon/Xoff Sensitive - Base Station setup.................. 1-29